ORDER NO.
PIONEER ELECTRONIC CORPORATION
4-1, Meguro 1-Chome, Meguro-ku, Tokyo 153-8654, Japan
PIONEER ELECTRONICS SERVICE, INC. P.O. Box 1760, Long Beach, CA 90801-1760, U.S.A.
PIONEER ELECTRONIC (EUROPE) N.V . Haven 1087, Keetberglaan 1, 9120 Melsele, Belgium
PIONEER ELECTRONICS ASIACENTRE PTE. LTD. 501 Orchard Road, #10-00 Wheelock Place, Singapore 238880
PIONEER ELECTRONIC CORPORATION 1998
COMPACT DISC PLAYER
RRV2031
TZZR SEPT. 1998 Printed in Japan
CDJ-500II
¶ Refer to the service manual RRV1831 for CDJ-500II/SL.
SY
AC110V/120V/220-230V/240V
With the voltage selector
Type
THIS MANUAL IS APPLICABLE TO THE FOLLOWING MODEL(S) AND TYPE(S).
CDJ-500II
Model
Power Requirement
The voltage can be converted by the
following method.
CDJ-500II
2
IMPORTANT
THIS PIONEER APPARATUS CONTAINS
LASER OF CLASS 1.
SERVICING OPERATION OF THE APPARATUS
SHOULD BE DONE BY A SPECIALLY
INSTRUTED PERSON.
LASER DIODE CHARACTERISTICS
MAXIMUM OUTPUT POWER: 5 mw
WAVELENGTH: 780 785 nm
1. SAFETY INFORMATION
This service manual is intended for qualified service technicians; it is not meant for the casual
do-it-yourselfer. Qualified technicians have the necessary test equipment and tools, and have been
trained to properly and safely repair complex products such as those covered by this manual.
Improperly performed repairs can adversely affect the safety and reliability of the product and may
void the warranty. If you are not qualified to perform the repair of this product properly and safely, you
should not risk trying to do so and refer the repair to a qualified service technician.
LABEL CHECK
1. Laser Interlock Mechanism
ON/OFF switching of the switch for detecting loading state,
ON/OFF switching of the clamp completion, close comple-tion
and shutter switches are detected by the system micropro-
cessor. The design of this interlook mechanism prevents
laser diode oscillation when even one of the clamp completion,
close completion and shutter switches is OFF (High level).
Accordingly, the interlock will no longer function and the
laserdiode will oscillater if all three of these switcher are set
deliber-ately to ON(Low level).
The interlock also does not function in the test mode
.
Laser diode oscillation will continue, if pin 1 of M51593FP
(IC101) on the PRE AMP BOARD ASSY mounted on the
pickupassembly is connected to GND, or pin 19 is connected to
low level (ON), or else the terminals of Q101 are shorted to
each other (fault condition).
2. When the cover is opened, close viewing of the objective lens
with the naked eye will cause exposure to a Class 1 laser
beam.
Refer to page 22 on the service manual RRV1831
Additional Laser Caution
Chassis
right side
No.4 (VRW1297)
No.3 (VRW1094)
FRONT
CDJ-500II
3
PCB ASSEMBLIES
NSP
MOTHER BOARD Assy
DWM1492
DWM2081
P6-70
MAIN BOARD Assy
DWX1794
DWX1899
P6-72
TRANSFORMER
DWR1223
DWR1302
BOARD Assy
P7-121
NSP
VOLTAGE SELECTOR
DWS1256
DWS1295
BOARD Assy
PACKING
P3-4
Operating Instructions(English
DRB1219
Not used
/French/German/Italian/Dutch/
Swedish/Spanish/Chinese)
P3-4
Operating Instructions(English
Not used
DRB1222
/French/German/Italian/
Swedish/Spanish)
P3-10
Packing Case
DHG1792
DHG1871
EXTERIOR
P6-43
Power Knob
DNK2942
DNK3602
P6-89
NSP
Rear Panel
DNC1465
DNC1496
Power Switch
Not used
DSA1024
No.1
Capacitor Cover
Not used
VEC1912
No.2
P7-119
NSP
Caution Label
PRW1018
Not used
Caution Label
Not used
VRW1094
*
NSP
Caution Label HE
Not used
VRW1297
*
2. CONTRAST OF MISCELLANEOUS PARTS
Notes: · The numbers in the remarks column corresponds to the number on the exploded diagram, Refer to "EXPLODED VIEWS".
· Marked " * " are refered to "1. SAFETY INFORMATION".
Part No.
Ref. No.
Mark
Symbol and Description
CDJ-500II
CDJ-500II
Remarks
SL
SY
CDJ-500II/SY and CDJ-500II/SL are constructed the same except for the following:
CONTRAST TABLE
NOTES :
÷ Parts marked by " NSP " are generally unavailable because they are not in our Master Spare Parts List.
÷ The
mark found on some component parts indicates the importance of the safety factor of the part.
Therefore, when replacing, be sure to use parts of identical designation.
÷ Reference Nos. indicate the pages and Nos. in the service manual for the base model.
÷ When ordering resistors, first convert resistance values into code form as shown in the following examples.
Ex. 1
When there are 2 effective digits (any digit apart from 0), such as 560 ohm and 47k ohm (tolerance is shown by
J = 5%, and K = 10%).
560
= 56 × 101= 561 ................................................... RD1/4PU 5 6 1 J
47k
= 47 × 10 3 = 473 .................................................. RD1/4PU 4 7 3 J
0.5
= R50 ...................................................................... RN2H Â 5 0 K
1
= 1R0 ......................................................................... RS1P 1 Â 0 K
Ex. 2
When there are 3 effective digits (such as in high precision metal film resistors).
5.62k
= 562 × 10 1 = 5621 ........................................... RN1/4PC 5 6 2 1 F
EXPLODED VIEWS
PMH30P060FMC
Rear Panel
Power Transformer
TRANSFORMER
BOARD ASSY
No.2
No.1
CDJ-500II
4
Q406, Q407
Not used
2SD2114K
R433
RN1/10SE1001D
RN1/10SE4700D
R434
RN1/10SE1001D
RN1/10SE4700D
R435
RS1/10S0R0J
RN1/10SE5100D
R436
RS1/10S0R0J
RN1/10SE5100D
R441
RS1/10S182J
RS1/10S561J
R449
RS1/10S0R0J
RS1/10S471J
R450
RS1/10S0R0J
RS1/10S471J
R496
RD1/4PU822J
RD1/4PU622J
R499
RD1/4PU822J
RD1/4PU622J
7 CONTRAST OF PCB ASSEMBLIES
Note : · Refer to 3. SCHEMATIC DIAGRAM.
Mark
Symbol and Description
Part No.
DWX1794
DWX1899
Remarks
MAIN BOARD ASSY
DWX1899 and DWX1794 are constructed the same except for the following:
BOARD IN JUMPERWIRE (ORG)
DDF1002
DDF1003
BOARD IN JUMPERWIRE (GRY)
DDF1003
DDF1004
BOARD IN JUMPERWIRE (VLT)
DDF1004
DDF1005
BOARD IN JUMPERWIRE (BUL)
DDF1005
DDF1013
Mark
Symbol and Description
Part No.
DWR1223
DWR1302
Remarks
TRANSFORMER BOARD ASSY
DWR1302 and DWR1223 are constructed the same except for the following:
JUMPERWIRE UNIT (ORG)
Not used
DDF1014
Mark
Symbol and Description
Part No.
DWS1256
DWS1295
Remarks
VOLTAGE SELECTOR BOARD ASSY
DWS1295 and DWS1256 are constructed the same except for the following:
I F
E F
F F
Note : · Refer to 3. SCHEMATIC DIAGRAM.
Note : · Refer to 3. SCHEMATIC DIAGRAM.
CDJ-500II
5
A
B
C
D
1
234
1
2
3
4
TO IC701 P56(MUTE)
TO IC701 P12(CONT2)
TO IC701 P11(CONT1)
TO
BUS
AH
TO BUS AH
TO IC302 BUS AF
TO
IC301
P58(C16M)
TO
IC301
P61(EMPH)
TO
AUDIO
OUT
ASSY
MAIN BOARD ASSY
(DWX1899)
· The differences of adjacencies to IC402
E F
3. SCHEMATIC DIAGRAM
E F
MAIN BOARD ASSY
¶