Operating Instructions
COMPACT DISC PLAYER
CDJ-400
2
The exclamation point within an equilateral
triangle is intended to alert the user to the
presence of important operating and
maintenance (servicing) instructions in the
literature accompanying the appliance.
The lightning flash with arrowhead symbol,
within an equilateral triangle, is intended to
alert the user to the presence of uninsulated
"dangerous voltage" within the product's
enclosure that may be of sufficient
magnitude to constitute a risk of electric
shock to persons.
CAUTION:
TO PREVENT THE RISK OF ELECTRIC
SHOCK, DO NOT REMOVE COVER (OR
BACK). NO USER-SERVICEABLE PARTS
INSIDE. REFER SERVICING TO QUALIFIED
SERVICE PERSONNEL.
CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN
IMPORTANT
D3-4-2-1-1_En-A
NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to
Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in
a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not
installed and used in accordance with the instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular installation. If this equipment does
cause harmful interference to radio or television reception, which can be determined by turning the equipment off
and on, the user is encouraged to try to correct the interference by one or more of the following measures:
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
Consult the dealer or an experienced radio/TV technician for help.
D8-10-1-2_En
WARNING
This equipment is not waterproof. To prevent a fire
or shock hazard, do not place any container filled
with liquid near this equipment (such as a vase or
flower pot) or expose it to dripping, splashing, rain
or moisture.
D3-4-2-1-3_A_En
WARNING: Handling the cord on this product or
cords associated with accessories sold with the
product will expose you to chemicals listed on
proposition 65 known to the State of California and
other governmental entities to cause cancer and
birth defect or other reproductive harm.
D36-P4_A_En
Wash hands after handling
NOTE: THE NO USER-SERVICEABLE PARTS COMPARTMENT WARNING IS LOCATED ON THE APPLIANCE BOTTOM.
This Class B digital apparatus complies with
Canadian ICES-003.
Cet appareil numérique de la Classe B est conforme
à la norme NMB-003 du Canada.
D8-10-1-3_EF
IMPORTANT NOTICE THE SERIAL NUMBER FOR
THIS EQUIPMENT IS LOCATED ON THE BOTTOM.
PLEASE WRITE THIS SERIAL NUMBER ON YOUR
ENCLOSED WARRANTY CARD AND KEEP IN A
SECURE AREA. THIS IS FOR YOUR SECURITY.
D1-4-2-6-1_En
Information to User
Alteration or modifications carried out without
appropriate authorization may invalidate the user's
right to operate the equipment.
D8-10-2_En
POWER-CORD CAUTION
Handle the power cord by the plug. Do not pull out the
plug by tugging the cord and never touch the power
cord when your hands are wet as this could cause a
short circuit or electric shock. Do not place the unit, a
piece of furniture, etc., on the power cord, or pinch the
cord. Never make a knot in the cord or tie it with other
cords. The power cords should be routed such that they
are not likely to be stepped on. A damaged power cord
can cause a fire or give you an electrical shock. Check
the power cord once in a while. When you find it
damaged, ask your nearest PIONEER authorized
service center or your dealer for a replacement.
S002_En
Thank you for buying this Pioneer product.
Please read through these operating instructions so you will know how to operate your model properly. After you have finished
reading the instructions, put them away in a safe place for future reference.
In some countries or regions, the shape of the power plug and power outlet may sometimes differ from that shown in the explanatory
drawings. However the method of connecting and operating the unit is the same.
K015 En
CAUTION: This product satisfies FCC regulations
when shielded cables and connectors are used to
connect the unit to other equipment. To prevent
electromagnetic interference with electric appliances
such as radios and televisions, use shielded cables
and connectors for connections.
D8-10-3a_En
Read these instructions.
Keep these instructions.
Heed all warnings.
Follow all instructions.
Do not use this apparatus near water.
Clean only with dry cloth.
Do not block any ventilation openings. Install in
accordance with the manufacturer's instructions.
Do not install near any heat sources such as
radiators, heat registers, stoves, or other apparatus
(including amplifiers) that produce heat.
Do not defeat the safety purpose of the polarized or
grounding-type plug. A polarized plug has two
blades with one wider than the other. A grounding
type plug has two blades and a third grounding
prong. The wide blade or the third prong are
provided for your safety. If the provided plug does
not fit into your outlet, consult an electrician for
replacement of the obsolete outlet.
Protect the power cord from being walked on or
pinched
particularly
at
plugs,
convenience
receptacles, and the point where they exit from the
apparatus.
1)
2)
3)
4)
5)
6)
7)
8)
9)
10)
Only use attachments/accessories specified by the
manufacturer.
Use only with the cart, stand, tripod, bracket, or
table specified by the manufacturer, or sold with the
apparatus. When a cart is used, use caution when
moving the cart/apparatus combination to avoid
injury from tip-over.
Unplug this apparatus during lightning storms or
when unused for long periods of time.
Refer all servicing to qualified service personnel.
Servicing is required when the apparatus has been
damaged in any way, such as power-supply cord or
plug is damaged, liquid has been spilled or objects
have fallen into the apparatus, the apparatus has
been exposed to rain or moisture, does not operate
normally, or has been dropped.
P1-4-2-2_En
11)
12)
13)
14)
CAUTION
This product is a class 1 laser product, but this
product contains a laser diode higher than Class 1.
To ensure continued safety, do not remove any covers
or attempt to gain access to the inside of the product.
Refer all servicing to qualified personnel.
The following caution label appears on your unit.
Location: Inside of the player
CLASS 1
LASER PRODUCT
APPAREIL Á LASER
DE CLASSE 1
D3-4-2-1-8_B_En
CAUTION
ATTENTION
CLASS 3B INVISIBLE LASER RADIATION
WHEN OPEN, AVOID EXPOSURE TO BEAM.
RADIATIONS LASER INVISIBLES DE CLASSE 3B QUAND
OUVERT. ÉVITEZ TOUT EXPOSITIONAU FAISCEAU.
ADVARSEL
KLASSE 3B USYNLIG LASERSTRÅLING VED ÅBNING.
UNDGÅ UDSÆTTELSE FOR STRÅLING.
VARNING
KLASS 3B OSYNLIG LASERSTRÅLNING NÄR DENNADEL
ÄR ÖPPNAD. UNDVIK ATT UTSÄTTADIG FÖR STRÅLEN.
VARO!
AVATTAESSA OLET ALTTIINA NÄKYMÄTTÖMÄLLE
LUOKAN 3B LASERSÄTEILYLLE. ÄLÄ KATSO SÄTEESEEN.
PRECAUCIAÓN CUANDOSEABREHAYRADIACIÓN LÁSER DE CLASE 3B
INVISIBLE. EVITE LA EXPOSICIÓN A LOS RAYOS LÁSER.
VORSICHT
BEI GEÖFFNETERABDECKUNG IST UNSICHTBARE LASERSTRAHLUNG
DER KLASSE 3B IM GERÄTEINNEREN VORHANDEN. NICHT DEM
LASERSTRAHLAUSSETZEN!
DRW2308-A
CAUTION
The POWER switch on this unit will not completely
shut off all power from the AC outlet. Since the
power cord serves as the main disconnect device for
the unit, you will need to unplug it from the AC outlet
to shut down all power. Therefore, make sure the
unit has been installed so that the power cord can
be easily unplugged from the AC outlet in case of an
accident. To avoid fire hazard, the power cord should
also be unplugged from the AC outlet when left
unused for a long period of time (for example, when
on vacation).
D3-4-2-2-2a_A_En
VENTILATION CAUTION
When installing this unit, make sure to leave space
around the unit for ventilation to improve heat
radiation (at least 5 cm at rear, and 3 cm at each
side).
WARNING
Slots and openings in the cabinet are provided for
ventilation to ensure reliable operation of the
product, and to protect it from overheating. To
prevent fire hazard, the openings should never be
blocked or covered with items (such as newspapers,
table-cloths, curtains) or by operating the
equipment on thick carpet or a bed.
D3-4-2-1-7b_A_En
WARNING
To prevent a fire hazard, do not place any naked
flame sources (such as a lighted candle) on the
equipment.
D3-4-2-1-7a_A_En
3
S001_En
Selecting fine audio equipment such as the unit
you've just purchased is only the start of your
musical enjoyment. Now it's time to consider how
you can maximize the fun and excitement your
equipment offers. This manufacturer and the
Electronic Industries Association's Consumer
Electronics Group want you to get the most out of
your equipment by playing it at a safe level. One that
lets the sound come through loud and clear without
annoying blaring or distortion-and, most importantly,
without affecting your sensitive hearing.
Sound can be deceiving. Over time your hearing
"comfort level" adapts to higher volumes of sound.
So what sounds "normal" can actually be loud and
harmful to your hearing. Guard against this by
setting your equipment at a safe level BEFORE your
hearing adapts.
To establish a safe level:
· Start your volume control at a low setting.
· Slowly increase the sound until you can hear it
comfortably and clearly, and without distortion.
Once you have established a comfortable sound
level:
· Set the dial and leave it there.
Taking a minute to do this now will help to prevent
hearing damage or loss in the future. After all, we
want you listening for a lifetime.
We Want You Listening For A Lifetime
Used wisely, your new sound equipment will
provide a lifetime of fun and enjoyment. Since
hearing damage from loud noise is often
undetectable until it is too late, this manufacturer
and the Electronic Industries Association's
Consumer Electronics Group recommend you avoid
prolonged exposure to excessive noise. This list of
sound levels is included for your protection.
Decibel
Level Example
30
Quiet library, soft whispers
40
Living room, refrigerator, bedroom away from traffic
50
Light traffic, normal conversation, quiet office
60
Air conditioner at 20 feet, sewing machine
70
Vacuum cleaner, hair dryer, noisy restaurant
80
Average city traffic, garbage disposals, alarm clock
at two feet.
THE FOLLOWING NOISES CAN BE DANGEROUS
UNDER CONSTANT EXPOSURE
90
Subway, motorcycle, truck traffic, lawn mower
100
Garbage truck, chain saw, pneumatic drill
120
Rock band concert in front of speakers,
thunderclap
140
Gunshot blast, jet plane
180
Rocket launching pad
Information courtesy of the Deafness Research Foundation.
If the AC plug of this unit does not match the AC
outlet you want to use, the plug must be removed
and appropriate one fitted. Replacement and
mounting of an AC plug on the power supply cord of
this unit should be performed only by qualified
service personnel. If connected to an AC outlet, the
cut-off plug can cause severe electrical shock. Make
sure it is properly disposed of after removal.
The equipment should be disconnected by removing
the mains plug from the wall socket when left
unused for a long period of time (for example, when
on vacation).
D3-4-2-2-1a_A_En
Operating Environment
Operating environment temperature and humidity:
+5 ºC to +35 ºC (+41 ºF to +95 ºF); less than 85 %RH
(cooling vents not blocked)
Do not install this unit in a poorly ventilated area, or in
locations exposed to high humidity or direct sunlight (or
strong artificial light)
D3-4-2-1-7c_A_En
FEDERAL COMMUNICATIONS COMMISSION DECLARATION OF CONFORMITY
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This
device may not cause harmful interference, and (2) this device must accept any interference received, including
interference that may cause undesired operation.
Product Name:
COMPACT DISC PLAYER
Model Number:
CDJ-400
Responsible Party Name: PIONEER ELECTRONICS SERVICE, INC.
Address:
1925 E. DOMINGUEZ ST. LONG BEACH, CA 90801-1760, U.S.A.
Phone:
1-800-421-1404
4
BEFORE OPERATING (FEATURES)
FEATURES
Designed for professional use by DJs, the CDJ-400 compact
disc player provides all the functions and performance re-
quired in disco clubs while offering performance, sound qua-
lity and functionality superior to analog players.
SCRATCH JOG EFFECT
Equipped with Scratch Jog Effect for new scratch sounds.
Equipped with three buttons [BUBBLE], [TRANS] and [WAH]
for new scratch sounds. Effects that are different from the nor-
mal scratch sound can be obtained, broadening the possibili-
ties of your DJ play.
DIGITAL JOG BREAK
Equipped with Digital Jog Break for original sound effects.
Individual remix assist functions [JET], [ROLL] and [WAH]
have been provided individually in three buttons. By choosing
a function and operating the jog dial in time with the music, a
new remix world can be experienced.
JOG DIAL
The large 115 mm diameter jog dial enables better handling
than an analog turntable.
I PITCH BEND
This function changes the music tempo depending on the di-
rection and speed the jog dial is rotated.
I SCRATCH PLAY
In the VINYL mode when the surface of the jog dial is pressed
playback is discontinued and then continues according to the
direction and speed the dial is rotated.
I FRAME SEARCH
Moves the pause position in frame units (1/75 sec) when the
jog dial is rotated in the pause mode.
I SUPER-FAST SEARCH
By turning the jog dial while holding down the manual search
button or the track search button, disc search can be per-
formed faster than normal search or track search functions.
TEMPO CONTROL
100 mm long high-precision slider allowing free speed adjust-
ment.
With a digital display calibrated in 0.02 % units (within a ±6 %
range), tempo adjustments can be made more easily and ac-
curately.
I TEMPO CONTROL RANGE
The maximum variable range can be set to four variable
ranges; ±6 %, ±10 %, ±16 %, WIDE, to provide easier operation
environment.
I MASTER TEMPO
Maintains the same pitch of sound while changing the music
tempo.
REVERSE PLAY
When the reverse button (DIRECTION REV) is pressed so that
the button's indicator lamp lights, play is performed in the re-
verse direction.
CUE
I BACK CUE
After storing cue points in memory, press the CUE button
while playing a track to return and start from the stored cue
point.
I AUTO CUE
Skips the non-recorded part at the top of a track and automati-
cally enters stand-by mode at the track's starting point, allow-
ing playback to begin instantly when the PLAY/PAUSE button
(
6) is pressed.
I CUE POINT SAMPLER
Playback can be started at one touch from a stored cue point,
convenient for confirming start points and as sampler.
CUE/LOOP MEMORY
This player is equipped with an internal memory that permits
the recording of cue point or loop point; the recorded points
can later be recalled as desired.
REAL TIME SEAMLESS LOOP
This function simplifies the setting and canceling of loops.
The loop can be set at the very instant the track is being
played. By setting a loop just before the end of the track, the
track can be made so that it doesn't stop. In addition, an
ADJUST mode has been added to enable one-touch adjust-
ments to the loop-out point, thereby facilitating the loop op-
eration.
RELOOP
Allows returning to the set loop position any number of times.
Press the RELOOP/EXIT button after canceling loop play to
return to the loop start position. By using the loop ON and OFF
combined with the rhythm of the track, new sound effects can
be created.
BEAT LOOP/LOOP DIVIDE
Automatically sets a loop-out point according to the track's
BPM and starts loop-play. Each additional time the button is
pressed, the loop is divided and a new rhythm produced.
PLAYING ADDRESS
The bar graph provides a visual reference of the track play-
back progress that enables the user to visualize the current
playback position, in the same way as is done with an analog
record by checking the position of the needle. The current po-
sition can be confirmed by the length of the graph, and in ad-
dition, the graph flashes to notify the ending of the track.
FADER START
When a Pioneer DJ mixer (sold separately) is connected, the
mixer's fader operation can be used to perform quick start
and back cue.
RELAY PLAY
Two CDJ-400 units can be connected in tandem to perform
automatic relay play.
When track playback stops on one of the players, the standby
mode of the other player is released and playback begins au-
tomatically.
5
BEFORE OPERATING (FEATURES)
CONTENTS
BEFORE OPERATING
FEATURES ................................................................... 4
DISCS USABLE WITH THIS UNIT .............................. 6
CAUTIONS REGARDING HANDLING ........................ 8
CONNECTIONS ............................................................ 9
PANEL FACILITIES .................................................... 11
OPERATIONS
DISC LOADING/UNLOADING ................................... 14
DJ PLAYER OPERATIONS ........................................ 15
Auto cue function ................................................ 15
Starting playback ................................................. 15
Resume function .................................................. 15
To stop playback .................................................. 15
To temporarily interrupt playback ..................... 15
Jog dial functions ................................................ 16
Fast-forward/fast-reverse ................................... 16
Track cueing ......................................................... 16
Rotary seach ........................................................ 16
Change playback speed ...................................... 17
Applying master tempo ...................................... 17
Scratch Jog Effect ............................................... 17
Digital Jog Break ................................................. 17
Cue point settings ............................................... 18
Mixing different tracks ........................................ 18
ADVANCED OPERATIONS ....................................... 19
Loop playback ...................................................... 19
Fader start playback ............................................ 19
Scratch play ......................................................... 19
Spin play ............................................................... 19
Reverse play ......................................................... 19
Cue point/loop point memory ............................ 20
Relay play using two players ............................. 20
Writing and reading data .................................... 20
MIDI SETTING ............................................................ 21
OTHER
TROUBLESHOOTING ................................................ 22
SPECIFICATIONS ....................................................... 23
OIL DAMPER FLOAT
OIL DAMPER FLOAT construction helps resist shakes and im-
pacts.
This unit features an OIL DAMPER FLOAT design, making it
harder for distortions and sound breakup to occur due to im-
pacts from operation and vibrations from the floor.
MULTI READ
Supports playback of CD-R and CD-RW discs. (Some discs
may not replay properly, however, due to certain special
characteristics of some discs and recorders, as well as due to
dirty or damaged discs.)
MP3 DJ PLAY
MP3 files recorded on CD-ROM or USB memory device can be
played with DJ functions.
PC CONNECTION
Virtually all the button and slider functions of the CDJ-400 can
be output to external devices.
These signals can then be used to control Pioneer's own DJ
software "DJS" as well as other computer software applica-
tions. In addition, music tracks played on the computer can be
output as audio from the CDJ-400.