PIONEER AVH-P7500DVDII - Service Manual Immediate Download

English

Français

Deutsch

Français

Italiano

Nederlands

AVH-P7600DVD

INST

ALLA

TION

MANUAL

MANUEL

D'INST

ALLA

TION

This product conforms to CEMA cord colors.

Le code de couleur des câbles utilisé pour ce produit est

conforme à CEMA.

Contents

Connecting the Units ................................ 1

Connecting the system ...................................... 3

Connecting the power cord (1) .......................... 4

Connecting the power cord (2) .......................... 5

When connecting to separately sold power

amp ............................................................ 7

When connecting with a rear view camera ...... 9

When connecting the external video

component and the display ...................... 11

Attaching the noise filters .............................. 12

Installation ................................................ 13

Installing the hide-away unit .......................... 13

DIN Front/Rear-mount .................................... 14

DIN Front-mount ............................................ 14

DIN Rear-mount .............................................. 15

Fixing the front panel ...................................... 16

Installing the remote control unit .................... 16

WARNING:

· To avoid the risk of accident and the

potential violation of applicable laws,

the front DVD or TV (sold separately)

feature should never be used while the

vehicle is being driven. Also, Rear

Displays should not be in a location

where it is a visible distraction to the

driver.

· In some countries or states the viewing

of images on a display inside a vehicle

even by persons other than the driver

may be illegal. Where such regulations

apply, they must be obeyed and this

unit's DVD features should not be used.

CAUTION:

· PIONEER does not recommend that

you install or service your display your-

self. Installing or servicing the product

may expose you to risk of electric shock

or other hazards. Refer all installation

and servicing of your display to autho-

rized Pioneer service personnel.

· Secure all wiring with cable clamps or

electrical tape. Do not allow any bare

wiring to remain exposed.

· Do not drill a hole into the engine com-

partment to connect the yellow lead of

the unit to the vehicle battery. Engine

vibration may eventually cause the insu-

lation to fail at the point where the wire

passes from the passenger compartment

into the engine compartment. Take

extra care in securing the wire at this

point.

· It is extremely dangerous to allow the

display lead to become wound around

the steering column or gearshift. Be sure

to install the display in such a way that

it will not obstruct driving.

· Make sure that wires will not interfere

with moving parts of the vehicle, such as

the gearshift, parking brake or seat slid-

ing mechanism.

· Do not shorten any leads. If you do, the

protection circuit may fail to work

properly.

Connecting the Units

English

Español

Deutsch

Français

Italiano

Nederlands

Note:

· This unit is for vehicles with a 12-volt battery and

negative grounding. Before installing it in a recre-

ational vehicle, truck, or bus, check the battery

voltage.

· To avoid shorts in the electrical system, be sure to

disconnect the battery cable before beginning

installation.

· Refer to the owner's manual for details on

connecting the power amp and other units, then

make connections correctly.

· Secure the wiring with cable clamps or adhesive

tape. To protect the wiring, wrap adhesive tape

around them where they lie against metal parts.

· Route and secure all wiring so it cannot touch any

moving parts, such as the gear shift, handbrake

and seat rails. Do not route wiring in places that

get hot, such as near the heater outlet. If the insu-

lation of the wiring melts or gets torn, there is a

danger of the wiring short-circuiting to the vehicle

body.

· Don't pass the yellow lead through a hole into the

engine compartment to connect to the battery.

This will damage the lead insulation and cause a

very dangerous short.

· Do not shorten any leads. If you do, the protection

circuit may fail to work when it should.

· Never feed power to other equipment by cutting

the insulation of the power supply lead of the unit

and tapping into the lead. The current capacity of

the lead will be exceeded, causing overheating.

· When replacing the fuse, be sure to only use a

fuse of the rating prescribed on the fuse holder.

· Since a unique BPTL circuit is employed, never

wire so the speaker leads are directly grounded or

the left and right speaker leads are common.

· If the RCA pin jack on the unit will not be used,

do not remove the caps attached to the end of the

connector.

· Speakers connected to this unit must be high-

power with minimum rating of 50 W and imped-

ance of 4 to 8 ohms. Connecting speakers with

output and/or impedance values other than those

noted here may result in the speakers catching

fire, emitting smoke, or becoming damaged.

· When an external power amp is being used with

this system, be sure not to connect the blue/white

lead to the amp's power terminal. Likewise, do

not connect the blue lead to the power terminal of

the auto-antenna. Such connection could cause

excessive current drain and malfunction.

· To avoid a short-circuit, cover the disconnected

lead with insulating tape. Insulate the unused

speaker leads without fail. There is a possibility of

a short-circuit if the leads are not insulated.

· To prevent incorrect connection, the input side of

the IP-BUS connector is blue, and the output side

is black. Connect the connectors of the same col-

ors correctly.

· This unit cannot be installed in a vehicle that

does not have an ACC (accessory) position on

the ignition switch. (Fig. 1)

Fig. 1

· The black lead is ground. Please ground this lead

separately from the ground of high-current prod-

ucts such as power amps.

If you ground the products together and the

ground becomes detached, there is a risk of dam-

age to the products or fire.

No ACC position

ACC position

ACC

· Cords for this product and those for other prod-

ucts may be different colors even if they have

the same function. When connecting this product

to another product, refer to the supplied manuals

of both products and connect cords that have the

same function.

Connecting the Units

Connecting the system

Fig. 2

Multi-CD player

(sold separately)

IP-BUS cable

This product

IP-BUS input

(Blue)

Hide-away TV tuner

(e.g. GEX-P6400TV)

(sold separately)

AV-BUS input (Blue)

AV-BUS cable (supplied

with TV tuner)

IP-BUS cable (supplied

with TV tuner)

Black

Blue

Black

Blue

Black

Blue

30 pin cable (supplied)

21 pin cable (supplied)

Violet

Black

Hide-away unit

(supplied)

Antenna jack

Antenna cable (supplied)

Navigation unit

(e.g. AVIC-880DVD)

(sold separately)

26 pin cable

Yellow

Auto-EQ&TA mic jack

See the operation manual.

3 m

(9 ft. 10 in.)

15 cm

(5-7/8 in.)

40 cm

(1 ft. 4 in.)

15 cm

(5-7/8 in.)

10 cm

(3-7/8 in.)

3 m

(9 ft. 10 in.)

3 m

(9 ft. 10 in.)

Connecting the power cord (1)

English

Español

Deutsch

Français

Italiano

Nederlands

Fig. 3

Yellow

To terminal always supplied

with power regardless of

ignition switch position.

Black (ground)

To vehicle (metal) body.

Black

Black/white

Center speaker

Hide-away unit

Fuse holder