PDR-155
SERVICE MANUAL
SERVICE MANUAL
DVD AV CONTROLLER
Silver model
MODEL
PDR-155
230-240V AC, 50Hz
120V AC, 60Hz
220-230V AC, 50/60Hz
SUPP
SUDT, SUDS
SUGT, SUGQ
Ref. No. 3748
102002
RC-506M
DVD AV CONTROLLER
PDR-
155
INPUT
STEREO
PHONES
MASTER VOLUME
MUTING
T- D
T- D
PROGRESSIVE
SCAN
SURROUND
MODE
PRESET
MEMORY
ACOUSTIC
CONTROL
STANDBY
TUNING/PRESET
STANDBY / ON
TV/
TV/SETUP
SETUP
TV/
TV/SETUP
SETUP
DIST
DISTANCE
ANCE
DIST
DISTANCE
ANCE
UP
UP
UP
UP
TV MUTING
TV MUTING
TV MUTING
TV
TV
PO
POWER
WER
TV
TV
PO
POWER
WER
TV
TV
INPUT
INPUT
TV
TV
INPUT
INPUT
DO
DOWN
WN
DO
DOWN
WN
TV V
TV VOL
OL +
TV V
TV VOL
OL +
TV V
TV VOL
OL -
TV V
TV VOL
OL -
789
+10
0
SHIFT
TV CH
TV CH -
TV CH
TV CH -
TV CH
TV CH +
TV CH
TV CH +
VOLUME
TEST T
TEST TONE
ONE
SP SETUP
SP SETUP
CH SEL
CH SEL
T- D SETUP
D SETUP
ON
789
STANDBY
INPUT SELECTOR
RECEIVER
COND.M
LAST M
FUNC.M
ANGLE
AUDIO
SUBTITLE
T-D/ST
LATE NIGHT
TOP MENU
MENU
RETURN
DVD
SETUP
REPEAT
TUNING
TUNER PRESET
MD/ CDR/ TAPE
A-B
STEP/ SLOW
TIMER
CLEAR
PROGRAM
SEARCH
ACOUSTIC
CONTROL
SURROUND
RANDOM
--/---
MODE
SLEEP
MUTING
DIMMER
DISPLAY
CLOCK
MODE
123
456
SAFETY-RELATED COMPONENT
WARNING!!
THE MARK
FOUND ON SOME COMPONENT
PARTS INDICATES THE CRITICAL FOR RISK OF
FIRE AND ELECTRIC SHOCK.
WHEN REPLACING, BE SURE TO USE PARTS OF
IDENTICAL DESIGNATION.
MAKE LEAKAGE-CURRENT OR RESISTANCE
MEASUREMENTS TO DETERMINE THAT EXPOSED
PARTS ARE ACCEPTABLY INSULATED FROM THE
SUPPLY CIRCUIT BEFORE RETURNING THE
APPLIANCE TO THE CUSTOMER.
PDR-155
SPECIFICATIONS-1
PDR-155 (DVD AV Controller)
Input/Impedance
Digital
TV:
OPTICAL -21~ -15 dB
Analog TV/LINE, MD/TAPE, CDR/VIDEO:
RCA L/R (200 mV/50 k )
Nominal output/Impedance
REC OUT (MD/TAPE, CDR/VIDEO): 200 mV/2.2 k
MULTI CH OUTPUT (Front L/R, Surround L/R, Center, Subwoofer): 1 V/470
Frequency response
Front, Surround:
120 Hz to 20 kHz, +1/ -3 dB (STEREO mode)
Subwoofer:
20 Hz to 120 Hz, + 1/-6 dB (STEREO mode)
Signal-to-noise ratio (S/N): more than 100 dB
Harmonic distortion: less than 0.08%
Acoustic controls
1:
+10 dB (82 Hz) subwoofer
2:
+10 dB (82 Hz) subwoofer
+6 dB (10,000 Hz) front
Muting : -60 dB
TUNER SECTION
FM
Tuning range : 87.50 to 108.00 MHz (50 kHz steps)
Usable sensitivity
Mono:
11.2 dBf, 1.0 µV (75 )
Stereo:
17.2 dBf, 2.0 µV (75 )
Capture ratio: 2.0 dB
Image rejection ratio
South America: 40 dB
Others: 85 dB
IF rejection ratio: 90 dB
Signal-to-noise ratio
Mono:
73 dB
Stereo:
67 dB
Alternate channel att.: 55 dB
AM suppression ratio: 50 dB
Harmonic distortion (1 kHz) Mono:
0.2%
Stereo:
0.3%
Frequency response: 30 to 15,000 Hz, ±1.0 dB
Stereo separation: 45 dB (1 kHz) 30 dB (100 to 10,000 Hz)
Muting level: 17.2 dBf
Antenna impedance: 75
AM
Tuning range:
South America: 530 to 1710 kHz (10 kHz steps)
Others: 522 to 1611 kHz (9 kHz steps)
Usable sensitivity: 30 µV
Image rejection ratio: 40 dB
IF rejection ratio: 40 dB
Signal-to-noise ratio: 40 dB
Harmonic distortion (400 Hz): 0.7%
Clock precision: monthly error, ±30 seconds (25 C)
PDR-155
SPECIFICATIONS-2
DVD SECTION
Signal readout system: PAL/AUTO color television system
Laser: Semiconductor laser, wavelength 650 nm (DVD)/780 nm (CD)
Digital audio frequency response
DVD linear audio:
48 kHz sampling 4 Hz - 22 kHz
96 kHz sampling 4 Hz - 44 kHz
CD audio:
4 Hz - 20 kHz
Signal-to-noise ratio (digital audio): More than 100 dB
Audio dynamic range (digital audio): More than 96 dB
Harmonic distortion (digital audio): Less than 0.01%
Wow and flutter Measuring limit [±0.001% (W. PEAK) ] or less
Operating conditions
Temperature: 5 C to 35 C
Operation status: Horizontal
Connectors
Video output: 1.0V (p-p), 75 , negative synch, pin jack x 1
S VIDEO:
(Y) 1.0V (p-p), 75 , negative synch, mini DIN4 pin jack x1
(C) 0.286V (p-p), 75
COMPONENT:
(Y) 1.0V (p-p), 75
(PR), (PB) 0.7V (p-p), 75 , COMPONENT jacks x 3
AUDIO OUTPUT (optical): -22.5 dBm x 2
AUDIO OUTPUT (analog): 2.0V (rms), 470 , pin jacks (L, R) x 2
GENERAL
Power Supply
South America, Taiwan: AC120 V, 60 Hz
Hong Kong, Other Asian area: AC220~230 V, 50/60 Hz
Power Consumption: 33 W
Power Consumption (standby mode): 2.5 W
Dimensions (W x H x D): 155 mm x 172.5 mm x 289.5 mm
Weight: 3.5 kg (7.7 lbs.)
SWA-155/
D-M7/D-M5
SPECIFICATIONS-3
SWA-155X (subwoofer)
INPUT: RCA L/R/C/SL/SR/ subwoofer (500 mV/47k )
AMPLIFIER SECTION
Power Output (FTC)
Front, Sound: 15 W x 5 (1kHz, 6
/EIAJ)
Subwoofer: 25 W (100 Hz, 3
/EIAJ)
Total harmonic distortion: 0.1% (Output: 5 W)
Signal-to-noise ratio: 100dB (STEREO: IHF A0.5V input)
SPEAKER SECTION
Type: J'DRIVE system, 16 cm OMF cone
GENERAL
Power Supply
South America, Taiwan: AC120V, 60 Hz
Hong Kong, Other Asian area: AC220~230 V, 50/60 Hz
Power Consumption: 65 W
Dimensions (W x H x D):185 mm x 299 mm x 312 mm
Weight: 8 kg
Others: Magnetic shielding (EIAJ)
D-M7 (speaker)
Type: 8 cm OMF cone (One for each)
Dimensions (W x H x D): 102 mm x 210 mm x 142 mm
Weight: Each 1.1 kg
Others: Magnetic shielding (EIAJ)
D-M3 (speaker)
Type: 8 cm OMF cone (One for each)
Dimensions (W x H x D): 85 mm x 120 mm x 112 mm
Weight: Each 0.6 kg
Others: Magnetic shielding (EIAJ)
RC-506M (remote controller)
Transmitter: Infrared
Signal range: Approx. 16 ft., 5 meters
Power supply: Two "AA" batteries (1.5V x 2)
Specifications and features are subject to change without notice.
Europe area: AC230-240V, 50Hz
PDR-155
SERVICE PROCEDURES-1
PROTECTION OF EYES FROM LASER BEAM DURING SERVICING
This set employs a laser. Therefore, be sure to follow
carefully the instructions below when servicing.
WARNING!!
SERVICE WARNING : DO NOT APPROACH THE
LASER EXIT WITH THE EYE TOO CLOSELY.
IN CASE IT IS NECESSARY TO CONFIRM LASER
BEAM EMISSION, BE SURE TO OBSERVE FROM
A DISTANCE OF MORE THAN 30cm FROM THE
SURFACE OF THE OBJECTIVE LENS ON THE
OPTICAL PICKUP BLOCK.
Laser Diode Properties
0.14 mW
LASER WARNING
Wavelength:
Laser output:
Wavelength:
Laser output:
CD
DVD
WARNING:
TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK,
DO NOT EXPOSE THIS APPLIANCE TO RAIN OR
MOISTURE.
CAUTION:
TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT
REMOVE COVER (OR BACK). NO USER-SERVICEABLE
PARTS INSIDE. REFER SERVICING TO QUALIFIED
SERVICE PERSONNEL.
The lightning flash with arrowhead symbol, within an equilateral
triangle, is intended to alert the user to the presence of uninsulated
"dangerous voltage" within the product's enclosure that may be of
sufficient magnitude to constitute a risk of electric shock to persons.
The exclamation point within an equilateral triangle is intended to alert
the user to the presence of important operating and maintenance
(servicing) instructions in the literature accompanying the appliance.
WARNING
RISK OF ELECTRIC SHOCK
DO NOT OPEN
RISQUE DE CHOC ELECTRIQUE
NE PAS
OUVRIR
AVIS
WARNING
This unit contains a semiconductor laser system and is classified
as a "CLASS 1 LASER PRODUCT". So, to use this model
properly, read this Instruction Manual carefully. In case of any
trouble, please contact the store where you purchased the unit.
To prevent being exposed to the laser beam, do not try to open
the enclosure.
VISIBLE LASER RADIATION WHEN OPEN AND INTERLOCK
FAILED OR DEFEATED. DO NOT STARE INTO BEAM.
THIS PRODUCT UTILIZES A LASER. USE OF CONTROLS OR
ADJUSTMENTS OR PERFORMANCE OF PROCEDURES
OTHER THAN THOSE SPECIFIED HEREIN MAY RESULT IN
HAZARDOUS RADIATION EXPOSURE.
The label on the right
is applied on the rear
panel except for USA
and Canadian
models.
1. This unit is a CLASS 1 LASER PRODUCT and employs a
laser inside the cabinet.
2. To prevent the laser from being exposed, do not remove
the cover. Refer servicing to qualified personnel.
"CLASS 1 LASER
PRODUCT "
DANGER:
CAUTION:
SERVICE PROCEDURE
1. Replacing the fuses
REF. NO.
PART NO.
DESCRIPTION
This symbol located near the fuse indicates that the
fuse used is show operating type, For continued protection against
fire hazard, replace with same type fuse , For fuse rating, refer to
the marking adjest to the symbol.
Ce symbole indique que le fusible utilise est e lent.
Pour une protection permanente, n'utiliser que des fusibles de meme
type. Ce demier est indique la qu le present symbol est apposre.
F9001
252158 or
252252
2520069 or
252270
252077 or
252277
1.6A-UL/T-237
1.6A-T/UL-ST2 <UDT,UDS>
0.8A-SE-EAK FSBFUSE
800MA-SE-TL250V
<UGQ,UGT,UPP>
4A-SE-EAK
4A-SE-TL250V
2. Safety-check out
(Only U.S.A. model)
After correcting the original service problem perform the
following safety check before releasing the set to the customer
Connect the insulating-resistance tester between the plug of
power supply cord and terminal GND on the back panel.
Specifications: More than 10M ohm at 500V
LASER BEAM CAUTION LABEL
F9501
650 nm
780 nm
0.43 mW