DV-SP800
SERVICE MANUAL
SERVICE MANUAL
SACD & DVD AUDIO/VIDEO PLAYER
Black, Silver and Golden models
MODEL
DV-SP800
Ref. No. 3742
102001
120V AC, 60Hz
230-240V AC, 50Hz
120/220-230V AC,
230-240V AC, 50/60Hz
BMDD
BMPP/SMPP
BMWT/GMWT
BMWR/GMWR
BMPS/GMPS
BMWS/GMWS
50/60Hz
RC-498DV
ON
STANDBY/ON
POWER
LAST MEMORY
CLEAR
REPEAT
VIDEO CIRCUIT
OFF
DIMMER
RANDOM
DISPLAY
STOP
PLAY
PAUSE
DV-SP800
SACD & DVD AUDIO/VIDEO PLAYER
PHONES LEVEL
MIN
MAX
PHONES
SACD
DVD
CD
ENTER
AUDIO SEL
VIDEO OFF
DISPLAY
DIMMER
MODE
TV / VCR
REMOTE CONTROLLER
RC-498DV
SEND / LEARN
STEP/ SLOW
PAUSE
STEP/ SLOW
MUTING
PRE
PROG
RAMMED & LEARNING CAPABILIT
Y
INPUT SELECTOR
AU
DI
O
TV
SUBTTL
LAS
T
M
ANG
LE
VOL
CH
DV
D
RCVR
VCR
ON
STANDBY
TV.VC
R
ENTER
A-B
PICTURE
COND M
FUNCTION M
SPEED
SURROUND
RANDOM PROGRAM CLEAR
REPEAT
-- / ---
SEARCH
1
2
3
45
6
7
8
9
+10
0
INPUT SELECTOR
TO
P M
ENU
MENU
RET
URN
SET
UP
Schematic diagram & Printed circuit board view only
SAFETY-RELATED COMPONENT
WARNING!!
THE MARK
FOUND ON SOME COMPONENT
PARTS INDICATES THE CRITICAL FOR RISK OF
FIRE AND ELECTRIC SHOCK.
WHEN REPLACING, BE SURE TO USE PARTS OF
IDENTICAL DESIGNATION.
MAKE LEAKAGE-CURRENT OR RESISTANCE
MEASUREMENTS TO DETERMINE THAT EXPOSED
PARTS ARE ACCEPTABLY INSULATED FROM THE
SUPPLY CIRCUIT BEFORE RETURNING THE
APPLIANCE TO THE CUSTOMER.
DV-SP800
SPECIFICATIONS
General
Power supply
USA & Canadian models
AC 120 V, 60 Hz
European models
AC 230 - 240 V, 50 Hz
South American models
AC 230
240 V, 50 Hz
World wide models
AC 120/220 - 230 V switchable, 50/60 Hz
Power consumption
USA & Canadian models
40 W
European models
38 W
Other models
36 W
Power consumption in standby mode
USA & Canadian models
8.6 W
European models
10.8 W
Other models
8.3 W
Weight
5.0 kg, 11.0 lbs.
External dimensions
435
91
314 mm (W/H/D), 17-1/8"
3-9/16"
12-3/8"
DVD Player
Signal system
USA & Canadian models
Standard NTSC
Other models
PAL/AUTO
Regional restriction code
USA & Canadian areas
1
European areas
2
South American areas
4
World wide areas
4, 3
Laser
Semiconductor laser, wavelength 650/780 nm
Frequency range (digital audio)
DVD linear sound:
48 kHz sampling 4 Hz to 22 kHz
96 kHz sampling 4 Hz to 44 kHz
DVD-Audio:
192 kHz sampling 4 Hz to 96 kHz
Audio CD:
4 Hz to 20 kHz
SACD:
4 Hz to 96 kHz
Signal-to-noise ratio (digital audio)
More than 118 dB
Audio dynamic range (digital audio)
More than 100 dB
Harmonic distortion (digital audio)
Less than 0.001 %
Wow and flutter
Below measurable level (less than +/-0.001 % (W.PEAK))
Operating conditions
Temperature: 5 C to 35 C, Operation status: Horizontal
Outputs
RGB signal output (European models)
0.7 V (p-p), 75 ohm, SCART socket
1
Video output
1.0 V (p-p), 75 ohm, negative sync., pin jack
2
S-video output
(Y) 1.0 V (p-p), 75 ohm, negative sync., Mini DIN 4-pin
2
(C) 0.286 V (p-p), 75 ohm
Component Signal output
(Y) 1.0 V (p-p), 75 ohm, negative sync., pin jack
1
(Cb, Pb)/ (Cr, Pr) 0.7 V (p-p), 75 ohm
Audio output (European models)
2.0 V (rms), 440 ohm, SCART socket
1
Audio output (digital output Optical)
- 22.5 dBm 2
Audio output (digital output Coaxial)
0.5 V (p-p), 75 ohm, pin jack
1
Audio output (analog audio)
2.0 V (rms), 440 ohm, pin jack (L, R)
2
Audio output (5.1 channel analog audio) 2.0 V (rms), 440 ohm, pin jack (Lo/Lt, Ro/Rt, SL1, SR1, C, SW)
1
1.4 V (rms), 440 ohm, pin jack (SL2, SR2)
1
Specifications and features are subject to change without notice.
-
xx
x
x
x
x
x
x
x
x
x
x
x
x
DV-SP800
SERVICE PROCEDURES-1
PROTECTION OF EYES FROM LASER BEAM DURING SERVICING
This set employs a laser. Therefore, be sure to follow
carefully the instructions below when servicing.
WARNING!!
SERVICE WARNING : DO NOT APPROACH THE
LASER EXIT WITH THE EYE TOO CLOSELY.
IN CASE IT IS NECESSARY TO CONFIRM LASER
BEAM EMISSION, BE SURE TO OBSERVE FROM
A DISTANCE OF MORE THAN 30cm FROM THE
SURFACE OF THE OBJECTIVE LENS ON THE
OPTICAL PICKUP BLOCK.
Laser Diode Properties
780 nm
0.14 mW
LASER WARNING
Wavelength:
Laser output:
650 nm
0.43 mW
Wavelength:
Laser output:
CD
DVD
WARNING:
TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK,
DO NOT EXPOSE THIS APPLIANCE TO RAIN OR
MOISTURE.
CAUTION:
TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT
REMOVE COVER (OR BACK). NO USER-SERVICEABLE
PARTS INSIDE. REFER SERVICING TO QUALIFIED
SERVICE PERSONNEL.
The lightning flash with arrowhead symbol, within an equilateral
triangle, is intended to alert the user to the presence of uninsulated
"dangerous voltage" within the product's enclosure that may be of
sufficient magnitude to constitute a risk of electric shock to persons.
The exclamation point within an equilateral triangle is intended to alert
the user to the presence of important operating and maintenance
(servicing) instructions in the literature accompanying the appliance.
WARNING
RISK OF ELECTRIC SHOCK
DO NOT OPEN
RISQUE DE CHOC ELECTRIQUE
NE PAS
OUVRIR
AVIS
WARNING
This unit contains a semiconductor laser system and is classified
as a "CLASS 1 LASER PRODUCT". So, to use this model
properly, read this Instruction Manual carefully. In case of any
trouble, please contact the store where you purchased the unit.
To prevent being exposed to the laser beam, do not try to open
the enclosure.
VISIBLE LASER RADIATION WHEN OPEN AND INTERLOCK
FAILED OR DEFEATED. DO NOT STARE INTO BEAM.
THIS PRODUCT UTILIZES A LASER. USE OF CONTROLS OR
ADJUSTMENTS OR PERFORMANCE OF PROCEDURES
OTHER THAN THOSE SPECIFIED HEREIN MAY RESULT IN
HAZARDOUS RADIATION EXPOSURE.
The label on the right
is applied on the rear
panel except for USA
and Canadian
models.
1. This unit is a CLASS 1 LASER PRODUCT and employs a
laser inside the cabinet.
2. To prevent the laser from being exposed, do not remove
the cover. Refer servicing to qualified personnel.
"CLASS 1 LASER
PRODUCT "
CAUTION:
CAUTION:
SERVICE PROCEDURE
1. Replacing the fuses
REF. NO.
PART NO.
DESCRIPTION
This symbol located near the fuse indicates that the
fuse used is show operating type, For continued protection against
fire hazard, replace with same type fuse , For fuse rating, refer to
the marking adjest to the symbol.
Ce symbole indique que le fusible utilise est e lent.
Pour une protection permanente, n'utiliser que des fusibles de meme
type. Ce demier est indique la qu le present symbol est apposre.
F911, F912
252300
2.5A-ULSE-TL250
<MPP, MWT, MPS, MWR>
2. Safety-check out
(Only U.S.A. model)
After correcting the original service problem perform the
following safety check before releasing the set to the customer
Connect the insulating-resistance tester between the plug of
power supply cord and terminal GND on the back panel.
Specifications: More than 10M ohm at 500V
LASER BEAM CAUTION LABEL
DV-SP800
SERVICE PROCEDURES-2
Factory-shipped condition
Push button "ON" (Mechanical SW)
Press the [STOP] and [STANDBY] same time.
(Wait until FL display "No Disc") .
Push button "STANDBY".
INITIALIZING
Others
Phones level volume -------- MIN.
SURR. switch ---------------- 1
Mechanical power switch -- ON
Remove the solder of Laser Diode shorting
1-1
Connect Pickup and DVD main circuit PC board by FFC(3 pcs).
1-2
Fix it with the DVD Mechanism
1-3
Remove the solder of Laser Diode shorting on Pickup.
1-4
Connect total unit of DVD Mechanism (DVD Main PCB + Mechanism) to output terminal.
Rear View
Short
DVDM Assy
Side
Short SW
Open
DV-SP800
PANEL VIEW-1
ON
STANDBY/ON
POWER
LAST MEMORY
CLEAR
REPEAT
VIDEO CIRCUIT
OFF
DIMMER
RANDOM
DISPLAY
STOP
PLAY
PAUSE
DV-SP800
SACD & DVD AUDIO/VIDEO PLAYER
PHONES LEVEL
MIN
MAX
PHONES
SACD
DVD
CD
POWER switch and STANDBY indicator
Turns on the main power supply for the DV-SP800.
The DV-SP800 enters standby state and the STANDBY indicator
lights up. Pressing the switch again to the off position (
OFF)
shuts down the main power supply into the DV-SP800.
Before turning on the power, make sure all cables are properly
connected.
STANDBY/ON button
When STANDBY/ON button is pressed to ON while the POWER
switch is set to ON, the DV-SP800 turns on and the STANDBY
indicator turns off. The indicator around
button lights up.
Pressing the button again returns the DV-SP800 to the standby
state. This state turns off the display, disables control functions.
VIDEO CIRCUIT OFF button and indicator
Press to switch the video signal off.
LAST MEMORY button
You can resume DVD or Video CD playback from the point you
last watched even if the disc is removed from the player. Press
LAST MEMORY during playback to set a Last Memory point.
When you want to resume playback of that disc, press LAST
MEMORY in the stop mode and playback starts from the
memorized point. Last Memory locations can be stored for up to 5
DVDs and 1 Video CD.
CLEAR button
Works in conjunction with a number of player functions. Use to
cancel repeat and random playback, and to edit programs.
DISC indicator
When playing a disc, the appropriate disc type indicator lights up.
Disc tray
When loading a disc, place discs in the disc tray with the label
side facing up.
TOP MENU button
Press to call up the top menu programmed on the DVD.
Depending on the DVD, the top menu may be identical to the
DVD menu.
Cursor ( // / ) button/ENTER button
Use
/ / /
to move through the options on menu screens and
to change settings. Use ENTER to implement settings selected
with the cursor buttons or to set items highlighted in a menu.
MENU button
Use to display or close the DVD menu or MP3 Navigator screen.
button
Press to open and close the disc tray.
PAUSE button
Press during playback to pause. Press again to resume playback.
STOP button
Press to stop playback. Whenever a disc is loaded in the player,
indicator above
STOP lights up.
PLAY button
Press to start or resume playback. Whenever a disc is loaded in
the player, indicator above
PLAY lights up.
DIMMER button
Toggle to control the lightness of the display (4 steps).
REPEAT button
Use to set the repeat mode.
RANDOM button
Press to play chapters/tracks in random order.
Remote control sensor
Point the remote control toward the remote sensor to operate the
player.
RETURN button
Use to go one menu back (current settings are maintained). Use
RETURN when you do not want to change the option setting in a
menu.
SETUP button
Press when the player is in either play or stop mode to open and
close the Setup screen.
DISPLAY button
Press during playback to display statistical disc information.
Press repeatedly to display different information.
/
button
Press to go back or advance to previous chapters/tracks. Press
and hold to perform fast-reverse/fast-forward playback scanning.
PHONES jack
This is a standard stereo jack for connecting stereo headphones.
The audio for the ANALOG OUTPUT CH 1 and CH 2 are sent to
the headphone speakers.
PHONES LEVEL dial
Use to control the phones level. Turn the dial clockwise to
increase the phones level and counterclockwise to decrease it.
FRONT PANEL
1
2
3
4
5
6
7
8
9 10 11
12
13
14
15
16
17
18
19
20
21
22
23
24
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24