NAD C272 - Owner's Manual Immediate Download

C 272

Stereo Power Amplifier

Owner's Manual

Manuel d'Installation

Bedienungsanleitung

Manual del Usuario

Manuale delle Istruzioni

Manual do Proprietário

Bruksanvisning

Warning: To reduce the risk of fire or electric shock, do not

expose this unit to rain or moisture.

The lightning flash with an arrowhead symbol within an equilateral

triangle, is intended to alert the user to the presence of uninsulated

"dangerous voltage" within the product's enclosure that may be of

sufficient magnitude to constitute a risk of electric shock to persons.

The exclamation point within an equilateral triangle is intended to

alert the user to the presence of important operating and

maintenance (servicing) instructions in the literature accompanying

the product.

Do not place this unit on an unstable cart, stand or tripod, bracket

or table. The unit may fall, causing serious injury to a child or adult

and serious damage to the unit. Use only with a cart, stand, tripod,

bracket or table recommended by the manufacturer or sold with

the unit. Any mounting of the device on a wall or ceiling should

follow the manufacturer's instructions and should use a mounting

accessory recommended by the manufacturer.

An appliance and cart combination should be moved with care.

Quick stops, excessive force and uneven surfaces may cause the

appliance and cart combination to overturn.

Read and follow all the safety and operating instructions before

connecting or using this unit. Retain this notice and the owner's

manual for future reference.

All warnings on the unit and in its operating instructions should be

adhered to.

Do not use this unit near water; for example, near a bath tub,

washbowl, kitchen sink, laundry tub, in a wet basement or near a

swimming pool.

The unit should be installed so that its location or position does not

interfere with its proper ventilation. For example, it should not be

situated on a bed, sofa, rug or similar surface that may block the

ventilation openings; or placed in a built-in installation, such as a

bookcase or cabinet, that may impede the flow of air through its

ventilation openings.

The unit should be situated from heat sources such as radiators,

heat registers, stoves or other devices (including amplifiers) that

produce heat.

The unit should be connected to a power supply outlet only of the

voltage and frequency marked on its rear panel.

The power supply cord should be routed so that it is not likely to be

walked on or pinched, especially near the plug, convenience

receptacles, or where the cord exits from the unit.

Unplug the unit from the wall outlet before cleaning. Never use

benzine, thinner or other solvents for cleaning. Use only a soft

damp cloth.

The power supply cord of the unit should be unplugged from the

wall outlet when it is to be unused for a long period of time.

Care should be taken so that objects do not fall, and liquids are not

spilled into the enclosure through any openings.

This unit should be serviced by qualified service personnel when:

A. The power cord or the plug has been damaged; or

B. Objects have fallen, or liquid has been spilled into the unit; or

C. The unit has been exposed to rain or liquids of any kind; or

D. The unit does not appear to operate normally or exhibits a

marked change in performance; or

E. The device has been dropped or the enclosure damaged.

DO NOT ATTEMPT SERVICING OF THIS UNIT

YOURSELF. REFER SERVICING TO QUALIFIED

SERVICE PERSONNEL

Upon completion of any servicing or repairs, request the service

shop's assurance that only Factory Authorized Replacement Parts

with the same characteristics as the original parts have been used,

and that the routine safety checks have been performed to

guarantee that the equipment is in safe operating condition.

REPLACEMENT WITH UNAUTHORIZED PARTS MAY RESULT IN FIRE,

ELECTRIC SHOCK OR OTHER HAZARDS.

ATTENTION

POUR ÉVITER LES CHOC ELECTRIQUES, INTRODUIRE LA

LAME LA PLUS LARGE DE LA FICHE DANS LA BORNE

CORRESPONDANTE DE LA PRISE ET POUSSER JUSQU'AU

FOND.

CAUTION

TO PREVENT ELECTRIC SHOCK, MATCH WIDE BLADE OF

PLUG TO WIDE SLOT FULLY INSERT.

If an indoor antenna is used (either built into the set or installed

separately), never allow any part of the antenna to touch the metal

parts of other electrical appliances such as a lamp, TV set etc.

CAUTION

POWER LINES

Any outdoor antenna must be located away from all power lines.

OUTDOOR ANTENNA GROUNDING

If an outside antenna is connected to your tuner or tuner-

preamplifier, be sure the antenna system is grounded so as to

provide some protection against voltage surges and built-up static

charges. Article 810 of the National Electrical Code, ANSI/NFPA No.

70-1984, provides information with respect to proper grounding of

the mast and supporting structure, grounding of the lead-in wire to

an antenna discharge unit, size of grounding conductors, location of

antenna discharge unit, connection to grounding electrodes and

requirements for the grounding electrode.

a. Use No. 10 AWG (5.3mm2) copper, No. 8 AWG (8.4mm2)

aluminium, No. 17 AWG (1.0mm2) copper-clad steel or bronze

wire, or larger, as a ground wire.

b. Secure antenna lead-in and ground wires to house with stand-off

insulators spaced from 4-6 feet (1.22 - 1.83 m) apart.

c. Mount antenna discharge unit as close as possible to where lead-

in enters house.

d. Use jumper wire not smaller than No.6 AWG (13.3mm2) copper,

or the equivalent, when a separate antenna-grounding electrode

is used. see NEC Section 810-21 (j).

EXAMPLE OF ANTENNA GROUNDING AS PER NATIONAL ELECTRICAL

CODE INSTRUCTIONS CONTAINED IN ARTICLE 810 - RADIO AND

TELEVISION EQUIPMENT.

NOTE TO CATV SYSTEM INSTALLER: This reminder is

provided to call the CATV system installer's attention to

Article 820-40 of the National Electrical Code that provides

guidelines for proper grounding and, in particular, specifies

that the ground cable ground shall be connected to the

grounding system of the building, as close to the point of

cable entry as practical.

CAUTION

RISK OF ELECTRIC

SHOCK DO NOT OPEN

ATTENTION:

RISQUE DE CHOC ELECTRIQUE

NE PAS OUVRIR

CAUTION: TO REDUCE THE RISK OF ELECTRIC

SHOCK, DO NOT REMOVE COVER (OR BACK). NO

USER SERVICEABLE PARTS INSIDE. REFER SERVICING

TO QUALIFIED SERVICE PERSONNEL.

IMPORTANT SAFETY INSTRUCTIONS

NAD

2003

C272

Serial No./No. De Series

FIXED IN

VARIABLE IN

+12V TRIGGER

AUTO

OFF

INPUT

SELECT

VAR

FIX

BRIDGE

MODE

OFF

SOFT

CLIPPING

SPEAKERS A

SPEAKERS B

MONO

INPUT

LEVEL

(dB)

MIN

MAX

(MONO)

(LEFT CH.)

OFF

(STEREO)

100mA

VACATION

OFF

SENSE/

DEFEAT

SLEEP/

WAKE

AC IN ~

230V~50HZ

EUROPEAN

VERSION ONLY

AC IN ~

120V~60HZ

REAR PANEL CONNECTIONS (FIGURE 1)

FRONT PANEL CONTROLS (FIGURE 2)

QUICK START

1. Connect the speakers to the Speaker A terminals and pre-

amplifier to the "FIXED IN" inputs.

2. Plug in the AC power cord.

3. Press the POWER button to turn the NAD C 272 on.

4. Press the required input selector.

NOTES ON INSTALLATION

Your NAD C 272 should be placed on a firm, level surface. Avoid

placing the unit in direct sunlight or near sources of heat and

damp. Allow adequate ventilation. Do not place the unit on a soft

surface like a carpet. Do not place it in an enclosed position, such

a bookcase or cabinet, that may impede the airflow through the

ventilation slots. Make sure the unit is switched off before making

any connections.

The RCA sockets on your NAD C 272 are colour coded for

convenience. Red and white are Right and Left audio respectively.

Use high quality leads and sockets for optimum performance and

reliability. Ensure that leads and sockets are not damaged in any

way and all sockets are firmly pushed home.

For best performance, use quality speaker leads of 16 gauge

(1.5mm) thickness or more. If the unit is not going to be used for

some time, disconnect the plug from the AC socket.

Should water get into your NAD C 272, shut off the power to the

unit and remove the plug from the AC socket. Have the unit

inspected by a qualified service technician before attempting to

use it again. DO NOT REMOVE THE COVER, THERE ARE NO

USER-SERVICEABLE PARTS INSIDE.

Use a dry soft cloth to clean the unit. If necessary, lightly dampen

the cloth with soapy water. Do not use solutions containing benzol

or other volatile agents.

REAR PANEL CONNECTIONS (FIGURE 1)

1. FIXED IN

The Fixed Inputs take the input signal straight to the power

amplifier's circuitry. This set of inputs is normally used in a system

with only one power amplifier or multiple but identical power

amplifiers. Refer also to section "Variable In" in this chapter for

more information.

Connect the output from a pre-amplifier or processor, such as a

surround-sound decoder, to this set of inputs. Use a twin RCA-to-

RCA lead to connect to the left and right `Audio Output' of the

pre-amp or processor to the Fixed-In sockets.

NOTES: Always turn the C 272 and other components in the

system off before connecting or It is disconnecting anything to the

"Fixed In" or Variable In" sockets.

When using the Fixed In sockets, make sure the "Input Select"

switch (No.2) is to the "Fix" position.

2. INPUT SELECT

The Input Select switch determines which input on the C 272 is

active. Set to "FIX" for use with "Fixed In" and to "VAR" for use

with "Variable In". Refer also to section "Variable In" in this

chapter for more information.

3. VARIABLE IN

Using the Variable inputs, it is possible to adjust the volume level

for both channels simultaneously, using the Input Level Control

(No. 4). This can be useful for:

· Level matching

In a surround sound or system with more than one set of

speakers, differences in levels can occur due to variances in

efficiency between these speakers. In case your preamplifier or

processor also has individual trims for each channel, set these

to neutral or mid position (usually marked as 0dB). Adjust the

Level Control so that the speakers driven by the C 272 have the

correct volume level compared to the other speakers, judging

from your listening position.

· Extended volume control range

Many systems have so much voltage gain that the speakers (or

your ears) are overdriven at any volume control setting higher

than 11 or 12 o'clock. As a result you are confined to using only

the lower half of the volume control's range, where adjustments

are imprecise and where channel balance errors tend to be

greater. If the input level is reduced, you can turn up your

processor's or preamplifier's volume control, making more

effective use of its range. (Suggestion: adjust the input level

controls so that your preferred maximum sound levels usually

occur at about 2 or 3 o'clock on the volume control.) As an

added benefit, this procedure suppresses any noise produced by

the preamp's high level circuitry (e.g. any residual hum or hiss

that does not go away when the Volume is turned down).

· Bi-Amping

Some loudspeakers have separate connection terminals for the

LF (Low Frequency) and HF (High Frequency) sections of the

speaker. This facility allows to "Bi-Amp" such speakers, where a

separate power amplifier is used for the LF and HF section, which

may improve overall sound quality. When Bi-Amping with

different models of power amplifiers, it is likely to occur that one

power amplifier has more "gain" than the other, resulting in a

mis-match in level for the woofer and tweeter of the speaker.

Adjust the level control so that woofer and tweeter are in perfect

balance with each other (identical gain of power amplifiers).

Connect the output from a pre-amplifier or processor, such as a

surround-sound decoder, to this set of inputs. Use a twin RCA-to-

RCA lead to connect to the left and right `Audio Output' of the

pre-amp or processor to the Fixed-In sockets.

NOTES: Always turn the C 272 and other components in the

system off before connecting or disconnecting anything to the

"Fixed In" or Variable In" sockets.

When using the "Variable In" sockets, make sure the "input

Select" switch (No.2) is to the "VAR" position.

4. INPUT LEVEL CONTROL

The Input Level control works in combination with "Variable In"

(No. 3) only. With the control the volume to the power amplifier

can be adjusted from zero (counter clock-wise) to maximum

(turned up all the way clock-wise). Refer also to section "Variable

In" in this chapter for more information.

NOTE: Always turn the C 272 and other components in the

system off before connecting or disconnecting anything to the

"Fixed In" or Variable In" sockets.

NAD C 272 Stereo Power Amplifier

5. SPEAKERS A & SPEAKERS B

The NAD C 272 is equipped with two sets of speaker connectors

wired in parallel to facilitate connection of multiple pairs of

speakers or "Bi-Wiring". Use the Speakers A connectors for the

`main' speakers and use the Speakers B connectors for a second

pair, for example, extension speakers located in another room.

Under normal operation, connect the right speaker to the

terminals market `R +' and `R-' ensuring that the `R+' is connected

to the `+' terminal on your loudspeaker and the `R-' is connected

to the loudspeaker's `-' terminal. Connect the terminals marked

`L+' and `L-' to the left speaker in the same way.

In Bridge Mode, connect the single speaker to the terminals

marked `R +' and `L+' ensuring that the `L+' is connected to the

`+' terminal on your loudspeaker and the R+ is connected to the

loudspeaker's `-' terminal. Refer also to section "Bridge Mode" in

this chapter (No. 6).

Always use heavy duty (16 gauge; 1.5mm, or thicker) stranded wire to

connect loudspeakers to your NAD C 272. The high-current binding

post terminals can be used as a screw terminal for cables terminating

in spade or pin sockets or for cables with bare wire ends.

BARE WIRES AND PIN CONNECTORS

Bare wires and pin sockets should be inserted into the hole in the

shaft of the terminal. Unscrew the speaker terminal's plastic

bushing until the hole in the screw shaft is revealed. Insert the pin

or bare cable end into the hole and secure the cable by tightening

down the terminal's bushing. Ensure bare wire from the speaker

cables does not touch the back panel or another socket . Ensure

that there is only 1/2" (1cm) of bare cable or pin and no loose

strands of speakers wire.

NOTE: Make sure the speaker impedance is 4 ohms or more when

connecting only one pair of speakers; make sure the speaker

impedance for all speakers is over 8 ohms when connecting two

sets of speakers. In Bridge Mode, the impedance of the

loudspeaker should also be 8 ohms or higher.

Always turn the C 272 and other components in the system off

before connecting or disconnecting speakers.

6. BRIDGE MODE

The stereo NAD C 272 power amplifier can be configured to be

mono (Bridge Mode), more than doubling its output power: 2 x

50 vs. 1 x 400 Watt. This way, the NAD C 272 can be used as part

of a high power stereo or home-theatre system, by connecting

adding additional power amplifiers.

Set the BRIDGE MODE switch to the "Bridge" position and

connect the speaker to the terminals marked `L +' and `R+'

ensuring that the `L+' is connected to the `+' terminal on your

loudspeaker and the `R+' is connected to the loudspeaker's `-'

terminal. Connect the source to the Left FIXED, or VARIABLE input.

In Bridged Mode the NAD C 272 will produce approximately

400W

into an 8 ohm loudspeaker. In this mode, the amplifier sections will

react as though the speaker impedance has been halved. Low

impedance speakers (under 8 ohms) are not recommended when

using Bridge Mode, as these may cause the amplifier's thermal cut-

out to operate if played at high levels.

The Bridge Mode indicator on the front panel (Fig. 2; No. 6) will

illuminate when the amplifier is in Bridge mode.

NOTES: Do not connect anything to the Right "Fixed In" or Right

"Variable In" sockets when Bridge Mode is selected.

Always turn the C 272 and other components in the system off

before connecting or disconnecting anything to the "Fixed In" or

Variable In" sockets.

7. SOFT CLIPPINGTM

When an amplifier is driven beyond its specified power output, a

hard, distorted sound can be heard on very loud sounds. This is

caused by the amplifier cutting off or `hard clipping' the peaks of

sound that it was not designed to reproduce. The NAD Soft

ClippingTM circuit gently limits the output of the system to

minimise audible distortion if the amplifier is overdriven.

If your listening involves moderate power levels you may leave the

Soft ClippingTM switch to Off. If you are likely to play at high levels,

that could stretch the amplifier's power capability, then switch Soft

ClippingTM On.

The Soft ClippingTM indicator on the front panel will illuminate

when the amplifier is in Soft Clip mode.

8. 12V TRIGGER AUTO ON-OFF

The C 272's 12V trigger input allows it to be switched to On and

Stand-by remotely by an external component.

Set the 12V Trigger switch set to the "ON" position to activate the

12V Trigger input. When the switch is set to the Off position, the

12V trigger input is not active. Refer to section "12V Trigger In"

below for more information.

9. 12V TRIGGER IN

This input allows the C 272 to be switched remotely to stand-by

and on or by ancillary equipment such as a preamp, AV processor,

etc. which are also equipped with a 12V trigger output.

For switching Stand-by/Power On of the C 272 by an external

component, connect the12V-trigger input of the C 272 to the

remote component's DC output jack. The plug required is a

standard 3.5mm Mini-Jack plug ("mono"): The tip is the live or +

connection, the shaft of the input jack is the 12V-trigger - or

ground connection.

NOTES: The C 272's 12V Trigger will work within a range of 6 to

15 V DC level and typically draws less than 10mA of current.

Check the specifications of the Trigger output terminal on the

remote component to ensure it is compatible with the C 272's

12V-trigger input. NAD components equipped with 12V output

triggers are fully compatible with the C 272's 12V input trigger.

Before making any connections to any 12V trigger input or output,

make sure all components are disconnected from the AC mains.

Failure to observe the above may result in damage to the C 272 or

any ancillary components attached to it. If in doubt over the

connections, installation and operation of the 12V trigger output

consult your NAD dealer.

10. AC LINE CORD

Plug the AC power cord into a live AC wall socket. Make sure all

connections have been made before connecting to mains.

11. VACATION ON/OFF

The VACATION switch is the master on/off control for the amplifier.

When the switch is in the ON state the amplifier is in standby as shown