MITSUBISHI LT3280 - Service Manual Immediate Download

MITSUBISHI DIGITAL ELECTRONICS AMERICA, INC.

9351 Jeronimo Road, Irvine, CA 92618-1904

CAUTION:

Before servicing this chassis, it is important that the service person read the "SAFETY PRECAUTIONS" and

"PRODUCT SAFETY NOTICE" contained in this manual.

MITSUBISHIELECTRIC Ser

Ser

Service

vice

Manual

2005

SPECIFICATIONS

LIQUID CRYSTAL DISPLAY TELEVISION

LT-3280 (LT-3280D)

LT-3780 (LT-3780D)

· Weight and dimensions shown are approximate.

· Design specifications are subject to change without notice.

· HDMITM is a trademark of HDMI Licensing, LLC

· Power

: AC 120V, 60Hz

[LT-3280D] 200W

[LT-3780D] 300W

Standby <5W

· LCD Panel

: Size/Resolution -

[LT-3280D] 32" diagonal, 16:9 / 1366x768

[LT-3780D] 37" diagonal, 16:9 / 1920x1080

: Pixel Pitch -

[LT-3280D] 0.519mm x 0.173mm x RGB

[LT-3780D] 0.4275mm x 0.1425mm x RGB

· Input Jacks

: MonitorLinkTM Audio/Video - HDMITM

: MonitorLinkTM Control - RS-232C

: PC Video - VGA /Mini D-sub 15 pin

: PC Audio - 3.5mm Mini-Jack

· Speakers

: 2 Way Bass Reflex Left & Right (2 X 5W)

The LT-3280 includes the LT-3280D, monitor and HD-4001, receiver/controller.

The LT-3780 includes the LT-3780D, monitor and HD-4001, receiver/controller.

This manual covers the LT-3280D and LT-3780D, monitors.

For the receiver/controller, see the HD-4001 Service Manual.

LT-3280D

W ith S tand: Height

W idth

Depth

W eight

25.4"

32.4"

12.8"

68.0 lbs

W /O S tand: Height

W idth

Depth

W eight

22.9"

32.4"

5.0"

44.3 lbs

LT-3780D

W ith S tand: Height

W idth

Depth

W eight

28.5"

37.3"

12.8"

80.0 lbs

W /O S tand: Height

W idth

Depth

W eight

26.0"

37.3"

5.3"

57.3 lbs

· Ca bine t Dim e nsions / W e ight

MODELS: LT-3280D/LT-3780D

Page 3

CONTENTS

PRODUCT SAFETY NOTICE & SAFETY PRECAUTIONS .................................................................. 5

DISASSEMBLY

Disassembly & Panel Replacement ................................................................................................ 7

LT-3280 Wire Dressing .................................................................................................................. 23

LT-3780 Wire Dressing .................................................................................................................. 24

ELECTRICAL ADJUSTMENTS

Initial Setup ................................................................................................................................... 25

CIRCUIT EXPLANATIONS & BLOCK DIAGRAMS

Circuit Explanations ...................................................................................................................... 27

Block Diagrams ............................................................................................................................ 32

TROUBLESHOOTING

Power Troubleshooting .................................................................................................................. 35

Video Troubleshooting ................................................................................................................... 38

Audio Troubleshooting ................................................................................................................... 40

Remote Control Troubleshooting ................................................................................................... 42

Front Switch Troubleshooting ........................................................................................................ 43

REPLACEMENT PARTS

LT-3280 Replacement Parts List .................................................................................................... 44

LT-3780 Replacement Parts List .................................................................................................... 45

SCHEMATICS

MODELS: LT-3280D/LT-3780D

Page 4

MODELS: LT-3280D/LT-3780D

Page 5

PRODUCT SAFETY NOTICE

Many electrical and mechanical parts in television receivers have special safety related characteristics. These character-

istics are often not evident from visual inspection nor can the protection afforded by them necessarily be obtained by

using replacement components rated for higher voltage, wattage, etc.

Replacement parts which have special safety characteristics are identified in this service manual.

The replacement for any safety part should be identical in value and characteristics.

SAFETY PRECAUTIONS

NOTICE:

Observe all cautions and safety related notes located inside the receiver cabinet and on the

receiver chassis.

WARNING:

Operation of this receiver outside the cabinet or with the cover removed presents a shock hazard

from the receiver's power supplies. Work on the receiver should not be attempted by anyone who is

not thoroughly familiar with the precautions necessary when working on high voltage equipment.

Do not install, remove or handle the LCD panel in any manner unless shatterproof goggles are

worn. People not so equipped should be kept away while the panel is being handled. Keep

the panel away from the body while handling.

When service is required, observe the original lead dress. Where a short-circuit has occurred, replace

those components that indicate evidence of overheating.

Leakage current check

Before returning the receiver to the customer, leakage current should be measured using following methods.

1. Cold Check

With the alternating current (AC) plug removed from the AC source, place a jumper across the two AC plug prongs.

Connect one lead of an ohm meter to the AC plug and touch the other lead to each exposed metal part (i.e. anten-

nas, handle bracket, metal cabinet, screw heads, metal overlay, control shafts, etc.), particularly any exposed metal

part that has a return path to the chassis. The resistance of the exposed metal parts having a return path to the

chassis should be a minimum of 1Meg Ohm. Any resistance below this value indicates an abnormal condition

and requires corrective action.

2. Hot Check ...Use the circuit shown below to perform the hot check test.

1. Keep switch S1 open and connect the receiver to the measuring circuit. Immediately after

connection, and with the switching devices of the receiver in their operating positions, measure

the leakage current for both positions of switch S2.

2. Close switch S1, energizing the receiver. Immediately after closing switch S1, and with the

switching devices of the receiver in their operating positions, measure the leakage current for both

positions of switch S2. Repeat the current measurements of items 1 and 2 after the receiver has

reached thermal stabilization. The leakage current must not exceed 0.5 milliampere (mA).