Operations
Preparation
Additional
Information
Remote
Control
AUDIO VIDEO SURROUND RECEIVER
VR-507
KRF-V7050D
INSTRUCTION MANUAL
B60-5027-00 01 MA (K, P, Y, M, X, I)
0009
This instruction manual is used to describe multiple models listed above.
Model availability and features (functions) may differ depending on the country and
sales area.
About the supplied remote control
Compared to standard remote controls, the remote control supplied with this receiver has several operation
modes. These modes enable the remote control to control other audio/video components. In order to
effectively use the remote control it is important to read the operating instructions and obtain a proper
understanding of the remote control and how to switch its operation modes (etc.).
Using the remote control without completely understanding its design and how to switch the operation modes
may result in incorrect operations.
KENWOOD CORPORATION
*5027/01-09/EN
3/15/01, 2:53 PM
1
2
Preparations
Units are designed for operation as follows.
U.S.A. and Canada ........................................... AC 120 V only
Australia ........................................................... AC 240 V only
Europe and U.K. ............................................... AC 230 V only
China and Russia ............................................ AC 220 V only
Other countries ............ AC 110-120 / 220-240 V switchable*
Unpack the unit carefully and make sure that all accessories are put aside
so they will not be lost.
Examine the unit for any possibility of shipping damage. If your unit is
damaged or fails to operate, notify your dealer immediately. If your unit
was shipped to you directly, notify the shipping company without delay.
Only the consignee (the person or company receiving the unit) can file a
claim against the carrier for shipping damage.
We recommend that you retain the original carton and packing materials
for use should you transport or ship the unit in the future.
Keep this manual handy for future reference.
Before applying the power
Caution : Read this page carefully to ensure safe
operation.
Unpacking
Note:
Our warranty does not cover damage caused by excessive line voltage
due to improper setting of the AC voltage selector switch.
* AC voltage selection
Move switch lever to
match your line voltage
with a small screw-
driver or other pointed
tool.
AC voltage selector switch
The AC voltage selector switch on the rear panel is set to the voltage that
prevails in the area to which the unit is shipped. Before connecting the
power cord to your AC outlet, make sure that the setting position of this
switch matches your line voltage. If not, it must be set to your voltage
in accordance with the following direction.
L
VIDEO 3
VIDEO 2
VIDEO 1
R
A
LC
L
R
L
R
B
PLAY IN
PLAY IN
PLAY IN
REC OUT
PLAY IN
MONITOR
OUT
VIDEO 1
DVD
R
75µs
AM 10kHz
FM 100kHz
50µs
AM 9kHz
FM 50kHz
DE-
EMPHASIS
CHANNEL
SPACE
AC 110V -
120V
AC 220V -
240V
WARNING :
TO PREVENT FIRE OR ELECTRIC SHOCK, DO
NOT EXPOSE THIS APPLIANCE TO RAIN OR
MOISTURE.
CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT
REMOVE COVER (OR BACK). NO USER-SERVICEABLE PARTS IN-
SIDE, REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.
THE LIGHTNING FLASH WITH ARROWHEAD SYMBOL,
WITHIN AN EQUILATERAL TRIANGLE, IS INTENDED TO ALERT
THE USER TO THE PRESENCE OF UNINSULATED "DAN-
GEROUS VOLTAGE" WITHIN THE PRODUCT'S ENCLOSURE
THAT MAY BE OF SUFFICIENT MAGNITUDE TO CONSTI-
TUTE A RISK OF ELECTRIC SHOCK TO PERSONS.
CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN
Safety precautions
THE EXCLAMATION POINT WITHIN AN EQUILATERAL TRI-
ANGLE IS INTENDED TO ALERT THE USER TO THE PRES-
ENCE OF IMPORTANT OPERATING AND MAINTENANCE
(SERVICING) INSTRUCTIONS IN THE LITERATURE ACCOM-
PANYING THE APPLIANCE.
*AC plug adaptor (1)
*Use to adapt the plug on the power
cord to the shape of the wall outlet.
(Accessory only for regions where use
is necessary.)
For KRF-V7050D
Batteries (R6/AA) (2)
Remote control unit (1)
RC-R0613
For VR-507
Batteries (R6/AA) (2)
Remote control unit (1)
RC-R0720
Accessories
FM indoor antenna (1)
AM loop antenna (1)
Microcomputer malfunction
If operation is not possible or an erroneous display appears, even though
all connections have been made properly, reset the microcomputer
referring to "In case of difficulty".
t
Maintenance of the unit
When the front panel or case becomes dirty, wipe with a soft, dry
cloth. Do not use thinner, benzine, alcohol, etc. for these agents may
cause discoloration.
In regard to contact cleaner
Do not use contact cleaners because it could cause a malfunction.
Be specially careful not to use contact cleaners containing oil, for
they may deform the plastic component.
*5027/01-09/EN
3/15/01, 2:53 PM
2
3
Operations
Preparations
Remote
Control
Additional
Information
Contents
Before applying the power
Before applying the power ................... 2
Safety precautions .............................................. 2
Unpacking .......................................................... 2
How to use this manual ...................................... 4
Special features .................................................. 5
Names and functions of parts ................ 6
Remote control unit (RC-R0720) (VR-507) .......... 7
Remote control unit (RC-R0613) (KRF-V7050D) .. 8
Setting up the system ......................... 9
Connecting audio components ......................... 10
Connecting video components ......................... 11
Connecting a DVD player (6-channel input) ...... 12
Digital connections ........................................... 13
Connecting to the AV AUX jacks ...................... 14
Connecting the antennas .................................. 14
Connecting the system control ......................... 15
Connecting the speakers .................................. 16
Connecting the terminals .................................. 17
Preparing the remote control ............................ 18
Preparing for surround sound ............... 19
Speaker settings ............................................... 19
Normal playback .............................. 20
Preparing for playback ...................................... 20
Listening to a source component ..................... 21
Adjusting the sound .......................................... 21
Recording ...................................... 22
Recording audio (analog sources) .................... 22
Recording video ................................................ 23
Recording audio (digital sources) ...................... 23
Listening to radio broadcasts ............... 23
Tuning radio stations ........................................ 23
Presetting radio stations manually .................... 24
Receiving preset stations .................................. 24
Receiving preset stations in order (P.CALL) ...... 24
Ambience effects .............................. 25
Surround modes ............................................... 25
Surround play ................................................... 27
DVD 6-channel playback .................................. 28
Convenient functions ........................................ 28
Basic remote control operations for other
components .................................... 31
Registering setup codes for other
components (RC-R0720) .................................. 31
Programming TV/VCR combo control .............. 31
Searching for your code ................................... 32
Checking the codes .......................................... 32
Re-assigning device keys ................................. 32
Changing volume lock ...................................... 33
Operating other components ............................ 33
Registering setup codes for other
components (RC-R0613) .................................. 34
Operating other components (RC-R0613) ........ 34
Setup code chart (for VR-507 (RC-R0720)) ...... 35
Setup code chart (for KRF-V7050D
(RC-R0613)) ...................................................... 39
CASSETTE deck, CD player & MD recorder
operations ......................................................... 40
Other components' operations ......................... 42
Caution : Read the pages marked
carefully to ensure safe operation.
Preparations
Operations
Remote Control
For the U.S.A.
FCC WARNING
This equipment may generate or use radio frequency energy. Changes
or modifications to this equipment may cause harmful interference
unless the modifications are expressly approved in the instruction
manual. The user could lose the authority to operate this equipment if an
unauthorized change or modification is made.
NOTE:
This equipment has been tested and found to comply with the limits for
a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits
are designed to provide reasonable protection against harmful interfer-
ence in a residential installation. This equipment may cause harmful
interference to radio communications, if it is not installed and used in
accordance with the instructions. However, there is no guarantee that
interference will not occur in a particular installation. If this equipment does
cause harmful interference to radio or television reception, which can be
determined by turning the equipment off and on, the user is encouraged
to try to correct the interference by one or more of the following measures:
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that
to which the receiver is connected.
Consult the dealer or an experienced radio / TV technician for help.
Note to CATV system installer:
This reminder is provided to call the CATV system installer's attention to
Article 820-40 of the NEC that provides guidelines for proper grounding
and, in particular, specifies that the cable ground shall be connected to
the grounding system of the building, as close to the point of cable entry
as practical.
For the U.S.A.
As an
ENERGY STAR® Partner, Kenwood Corpora-
tion has determined that this product meets the
ENERGY STAR® guidelines for energy efficiency.
This product can save energy. Saving energy reduces air pollution and
lowers utility bills.
Additional
Information
In case of difficulty ........................... 45
Specifications ................................. 47
*5027/01-09/EN
3/15/01, 2:53 PM
3
4
Preparations
Model name
Remote
Terminal
Control
Speaker out
Video 3
Front input
jacks
VR-507
RC-R0720
2 systems
Equipped
Equipped
(A, B)
KRF-V7050D
RC-R0613
2 systems
Equipped
Equipped
(A, B)
How to use this manual
This manual is divided into four sections, Preparations, Operations,
Remote Control, and Additional Information.
Preparations
Shows you how to connect your audio and video components to the
receiver and prepare the surround processor.
We will guide you to make setting up your system as easy as possible.
However, since this receiver works with all of your audio and video
components, connecting the system can be fairly complex.
Operations
Shows you how to operate the various functions available on the receiver.
Remote Control
Shows you how to operate other components using the remote control,
as well as a detailed explanation of all remote control operations. Once
you have registered your components with the proper setup codes, you'll
be able to operate both this receiver and your other AV components (TV,
VCR, DVD player, CD player, etc.) using the remote control supplied with
this receiver.
Additional Information
Shows you additional information such as "In case of difficulty"
(troubleshooting) and "Specifications".
Before applying the power
This manual covers the VR-507 and KRF-V7050D. Items such as functions,
number of jacks, and remote control details somewhat differ between
these models. To confirm the functions available on the model you have
purchased, refer to the table below.
Memory back up function
Please note that the following items will be deleted from the unit's
memory if the power cord is disconnected from the AC outlet for
approximately 2 days.
· Power mode.
· Input selector settings.
· Device preset.
· Picture output.
· Speaker ON/OFF
· Volume level.
· BASS, TREBLE, INPUT level.
· Subwoofer ON/OFF.
· Dimmer level.
· Monitor ON/OFF.
· MD/TAPE settings.
· 6ch/2ch input setting.
· Listen mode setting.
· Speaker settings.
· Input mode setting.
· Midnight mode setting.
· Broadcast band.
· Frequency setting.
· Preset stations.
· Tuning mode.
· CINEMA EQ.
· Source Direct.
*5027/01-09/EN
3/15/01, 2:53 PM
4
5
Preparation
Special features
True home theater sound
This receiver incorporates a wide variety of surround modes to bring you
maximum enjoyment from your video software. Select a surround mode
according to your equipment or the software you are going to play and
enjoy!
Dolby Digital
The DOLBY DIGITAL mode lets you enjoy full digital surround from
software processed in the Dolby Digital format. Dolby Digital provides
up to 5.1 channels of independent digital audio for better sound quality
and more powerful presence than conventional Dolby Surround.
Dolby PRO LOGIC II
Pro Logic II, whilst totally compatible with its predecessor PRO LOGIC,
provides greater advantages in surround sound. It allows user to enjoy
the conventional stereo or Dolby Surround with a convincing "5.1 like"
presentation. PRO LOGIC II offers special features for controlling the
overall spatial, dimensionality and frontal sound field imaging. Dolby
PRO LOGIC II produces an impressive surround sound from video
software marked
and three-dimensional space from
music CD. When listening to music, you will be able to enjoy the
experience of sheer STEREO surround sound.
Dolby 3 Stereo
This surround system reproduces theater-like surround sound from
video software marked
.
The 3 STEREO mode will redirect the Surround signal to the front left
and right speakers when only the front and center speakers are used.
DTS
DTS (Digital Theater System) is a 5.1 channel digital audio format that
provides five full-spectrum channels and one low-frequency (subwoofer)
channel for unprecedented clarity, optimum channel separation and a
(wide) dynamic range.
In the DTS mode, the 5.1 channel digital input from a DTS CD, LD or
DVD disc (carrying the "DTS" marking) can be played in Digital Surround.
Important:
When a DTS disc is played on a CD, LD or DVD player, noise may be
output from the analog output. It is recommended that you connect the
digital output of the player to the digital input of this unit.
Multi channel music (SRS Circle Surround
)
SRS Circle surround enables you to listen to multi channel sound from the
stereo source. We assume you have already enjoyed listening to Dolby
digital sound/DTS multi channel sound with your multi speakers. Now,
this time try listening to the stereo source (ex. Audio CD) using your multi
speakers. You may discover a new type of "stereo" sound through SRS
Circle Surround.
DSP surround modes
The DSP (Digital Signal Processor) used for this receiver incorporates a
variety of high quality adjustable sound fields, like "ARENA", "JAZZ
CLUB", THEATER", STADIUM" and "DISCO". It is compatible with
almost any kind of program source.
DVD 6-channel input
If you own a DVD player equipped with 6-channel output, this receiver
allows you to obtain the full surround sound impact of DVD source
material featuring multi-channel encoding. Since the source signals are
digital and each channel is input independently, the resulting ambience
is far superior to what can be achieved with conventional surround sound
systems.
CINEMA EQ.
Cinema EQ. mode will produce a more dynamic sound quality in any
conditions. You can enjoy a more impressive sound effect when you
switch CINEMA EQ. ON during Dolby Digital and DTS playback.
Universal IR (InfraRed) remote control
In addition to the basic receiver, the remote control supplied with this
receiver can also operate almost all of your remote controllable audio and
video components. Just follow the simple setup procedure to register the
components you have connected.
Before applying the power
*5027/01-09/EN
3/15/01, 2:53 PM
5