KENWOOD KDC-W707 - Owner's Manual Immediate Download

CD-RECEIVER

KDC-W808

KDC-W707

INSTRUCTION MANUAL

2 | English

Contents

Safety precautions

Notes

About CDs

About AAC, MP3 and WMA

General features

Power

Hiding the Control Panel

Selecting the Source

Volume

Attenuator

System Q

Speaker Setting

Audio Control

Audio Setup

Subwoofer Output

Display Setting

Text Selection for Display

Text Display Switching

Graphic part/ Spectrum Analyzer Display

Switching

Faceplate Angle Adjustment

Theft Deterrent Faceplate

TEL Mute

Tuner features

Tuning

Station Preset Memory

Auto Memory Entry

Preset Tuning

RDS features

Traffic Information

Radio Text Scroll

PTY (Program Type)

Program Type preset

Changing Language for PTY Function

CD/Audio file/External disc control

features

Playing CD & Audio file

Playing External Disc

Fast Forwarding and Reversing

Track/File Search

Disc Search/Folder Search

Track/File/Disc/Folder Repeat

Scan Play

Random Play

Magazine Random Play

Disc Random Play

Folder Select

Switching the Play mode

Letter Seek

Disc Naming (DNPS)

Text/Title Scroll

Menu system

Menu System

Security Code

Touch Sensor Tone

Manual Clock Adjustment

Date Adjustment

Date Mode

Synchronize Clock

Dimmer

OFF Wait Time Setting

Switching preout

Built-in Amp Setting

Dual Zone System Setting

B.M.S. (Bass Management System)

B.M.S. Frequency Offset

AMP Control

News Bulletin with Timeout Setting

Local Seek

Tuning Mode

AF (Alternative Frequency)

Restricting RDS Region (Region Restrict

Function)

Auto TP Seek

Monaural Reception

External Display Control

Auxiliary Input Display Setting & Disc Naming

Text Scroll

Built-in Auxiliary input Setting

Power OFF Timer

CD Read Setting

Voice Index

ACDrive firmware version display

Unique ID display

Audio Preset Memory

English |

The "AAC" logo is trademark of Dolby

Laboratories.

Audio Preset Call

Selecting Russian Characters

Demonstration mode Setting

Accessories/ Installation Procedure 40

Connecting Wires to Terminals

Installation

Removing the Unit

Troubleshooting Guide

Specifications

4 | English

Safety precautions

About CD players/disc changers

connected to this unit

Kenwood disc changers/ CD players released in

1998 or later can be connected to this unit.

Refer to the catalog or consult your Kenwood

dealer for connectable models of disc changers/

CD players.

Note that any Kenwood disc changers/ CD players

released in 1997 or earlier and disc changers made

by other makers cannot be connected to this unit.

Connecting unsupported disc changers/CD players

to this unit may result in damage.

Set the "O-N" Switch to the "N" position for the

applicable Kenwood disc changers/ CD players.

The functions you can use and the information

that can be displayed may differ depending on the

models being connected.

· You can damage both your unit and the CD changer if

you connect them incorrectly.

Lens Fogging

When you turn on the car heater in cold weather,

dew or condensation may form on the lens in the

CD player of the unit. Called lens fogging, this

condesnation on the lens may not allow CDs to

play. In such a situation, remove the disc and wait

for the condensation to evaporate. If the unit still

does not operate normally after a while, consult

your Kenwood dealer.

Faceplate

· Use the enclosed or dedicated faceplate. Using a

faceplate other than the specified one may cause

your unit to malfunction.

2WARNING

To prevent injury or fire, take the

following precautions:

· To prevent a short circuit, never put or leave any

metallic objects (such as coins or metal tools)

inside the unit.

2CAUTION

To prevent damage to the machine, take

the following precautions:

· Make sure to ground the unit to a negative 12V

DC power supply.

· Do not install the unit in a spot exposed to direct

sunlight or excessive heat or humidity. Also avoid

places with too much dust or the possibility of

water splashing.

· Do not place the faceplate or the faceplate case in

areas exposed to direct sunlight, excessive heat or

humidity. Also avoid places with too much dust or

the possibility of water splashing.

· To prevent deterioration, do not touch the

terminals of the unit or faceplate with your

fingers.

· Do not subject the faceplate to excessive shock,

as it is a piece of precision equipment.

· When replacing a fuse, only use a new fuse with

the prescribed rating. Using a fuse with the wrong

rating may cause your unit to malfunction.

· Do not apply excessive force to the open

faceplate or place objects on it. Doing so will

cause damage or breakdown.

· Do not use your own screws. Use only the screws

provided. If you use the wrong screws, you could

damage the unit.

Attach the panel while you are on the

vehicle

The panel lock arm appears when the panel is

removed. Therefore, the panel must be attached

while the electrical system of the car is operating.

Do Not Load 8cm(3-in.) CDs in the CD slot

If you try to load a 8cm (3 in.) CD with its adapter

into the unit, the adapter might separate from the

CD and damage the unit.

English |

Notes

· If you experience problems during installation,

consult your Kenwood dealer.

· If the unit fails to operate properly, press the Reset

button. The unit returns to factory settings when

the Reset button is pressed.

· Press the reset button if the disc auto changer fails

to operate correctly. Normal operation should be

restored.

Reset button

· The characters conforming to ISO 8859-1

character set can be displayed

· The characters conforming to ISO 8859-5 or ISO

8859-1 character set can be displayed. Refer

to <Selecting Russian Characters> (page 38).

(Russian sales area of KDC-W707)

· There are places in this manual where lit

indicators are described; however, the only time

an indicator will light is in the following settings.

When Indicator is selected as mentioned in <Text

Display Switching> (page 15)

· The illustrations of the display and the panel

appearing in this manual are examples used to

explain more clearly how the controls are used.

Therefore, what appears on the display in the

illustrations may differ from what appears on

the display on the actual equipment, and some

of the illustrations on the display may represent

something impossible in actual operation.

Cleaning the Unit

If the faceplate of this unit is stained, wipe it with a

dry soft cloth such as a silicon cloth.

If the faceplate is stained badly, wipe the stain off

with a cloth moistened with neutral cleaner, then

wipe it again with a clean soft dry cloth.

· Applying spray cleaner directly to the unit may affect its

mechanical parts. Wiping the faceplate with a hard cloth

or using a volatile liquid such as thinner or alcohol may

scratch the surface or erases characters.

Cleaning the Faceplate Terminals

If the terminals on the unit or faceplate get dirty,

wipe them with a dry, soft cloth.

Before using this unit for the first time

This unit is initially set on the Demonstration mode.

When using this unit for the first time, cancel the

<Demonstration mode Setting> (page 39).

About DAB Tuner control

Refer to

A group on the Instruction manual of DAB

Tuner KTC-9090DAB (optional accessory) for the

control method of DAB Tuner function.

However, the following control methods of the

function for this unit may be different from the

Instruction manual; therefore, refer to the following

supplemental instruction.

1. Select the preset band for Auto Ensemble

Memory Entry.

2. Press the [AME] button for at least 2 seconds.

Open Auto Ensemble Memory Entry.

After storing in the memory finishes, the

number of the pre-set buttons and the

ensemble label are displayed.

and <Languages to be displayed> in

At the operation to press [DISP] button, press [TI]

button.