KENWOOD KAC-X1D - Owner's Manual Immediate Download

XR-1S

In the interests of user-safety (Required by safety regulations in some countries) the set should be re-

stored to its original condition and only parts identical to those specified should be used.

MODEL

MODELL

XR-1S

PROJECTOR

PROJEKTOR

Im lnteresse der Benutzersicherheit (erforderliche Sicherheitsregeln in einigen Ländern) muß das Gerät in seinen

Originalzustand gebracht werden. Außerdem dürfen für die spezifizierten Bauteile nur identische Teile verwendet

werden.

SERVICE MANUAL

SERVICE-ANLEITUNG

SHARP CORPORATION

This document has been published to be used for

after sales service only.

The contents are subject to change without notice.

S74X5XR-1S///

XR-1S

CONTENTS

Page

INHALT

Seite

· SPECIFICATIONS ............................................. 3

· IMPORTANT SERVICE SAFETY

NOTES (for USA) .............................................. 4

· NOTE TO SERVICE PERSONNEL ................... 5

· OPERATION MANUAL ................................... 10

· DIMENSIONS ................................................. 16

· REMOVING OF MAJOR PARTS .................... 17

· RESETTING THE TOTAL LAMP TIMER ........ 21

· THE OPTICAL UNIT OUTLINE ....................... 23

· ELECTRICAL ADJUSTMENT ......................... 25

· TROUBLE SHOOTING TABLE ....................... 34

· CHASSIS LAYOUT ......................................... 82

· BLOCK DIAGRAM .......................................... 84

· OVERALL WIRING DIAGRAM ....................... 86

· DESCRIPTION OF SCHEMATIC DIAGRAM .. 88

· WAVEFORMS ................................................. 89

· SCHEMATIC DIAGRAM ................................. 90

· PRINTED WIRING BOARD ASSEMBLIES .. 117

· PARTS LIST

Ë ELECTRICAL PARTS ............................... 125

Ë CABINET AND MECHANICAL PARTS .... 134

Ë ACCESSORIES PARTS ............................ 138

Ë PACKING PARTS...................................... 138

· PACKING OF THE SET ................................ 139

· TECHNISCHE DATEN .................................... 44

· HINWEISE FÜR DAS

WARTUNGSPERSONAL ................................ 45

· BEDIENUNGSANLEITUNG ............................ 47

· ABMESSUNGEN ............................................ 53

· ENTFERNEN DER HAUPTTEILE .................. 54

· RÜCKSTELLEN DES

LAMPENBETRIEBSZEIT-TIMERS ................. 58

· BESCHREIBUNG DER OPTIK-EINHEIT ....... 60

· ELEKTRISCHE EINSTELLUNG ..................... 62

· FEHLERSUCHTABELLE ................................ 71

· CHASSIS-ANORDNUNG ............................... 82

· BLOCKSCHALTBILD ...................................... 84

· GESAMTSCHALTPLAN .................................. 86

· BESCHREIBUNG DES SCHEMATISCHEN

SCHALTPLANS .............................................. 88

· WELLENFORMEN .......................................... 89

· SCHEMATISCHER SCHALTPLAN ................. 90

· LEITERPLATTENEINHEITEN ...................... 117

· ERSATZTEILLISTE

Ë ELEKTRISCHE BAUTEILE ....................... 125

Ë GEHÄUSE UND MECHANISCHE

BAUTEILE ................................................. 134

Ë ZUBEHÖRTEILE ....................................... 138

Ë VERPACKUNGSTEILE ............................. 138

· VERPACKEN DES GERÄTS ........................ 139

XR-1S

Specifications

Product type Projector

Model XR-1S

Video system NTSC3.58/NTSC4.43/PAL/PAL-M/PAL-N/PAL-60/SECAM/DTV480I/DTV480P/DTV540P/DTV576I/

DTV576P/DTV720P/DTV1035I/DTV1080I/DTV1080I-50

Display method Single Chip Digital Micromirror DeviceTM (DMDTM) by Texas Instruments

DMD panel Panel size: 0.55" (13.7 mm) (8.2 [H]

× 10.9 [W] mm), 1 chip SVGA DMD

No. of dots: 480,000 dots (800 [H]

× 600 [V])

Lens 11.16

× zoom lens, F2.602.84, f = 19.322.6 mm

Projection lamp 150 W DC lamp

Component input signal (INPUT1) 15-pin mini D-sub connector

Y: 1.0 Vp-p, sync negative, 75

terminated

PB: 0.7 Vp-p, 75

terminated

PR: 0.7 Vp-p, 75

terminated

Horizontal resolution 520 TV lines (DTV720P)

Computer RGB input signal (INPUT 1) 15-pin mini D-sub connector

RGB separate/sync on green type analog input: 00.7 Vp-p, positive, 75

terminated

HORIZONTAL SYNC. SIGNAL: TTL level (positive/negative)

VERTICAL SYNC. SIGNAL: Same as above

S-video input signal (INPUT 2) 4-pin mini DIN connector

Y (luminance signal): 1.0 Vp-p, sync negative, 75

terminated

C (chrominance signal): Burst 0.286 Vp-p, 75

terminated

Video input signal (INPUT 3) RCA connector: VIDEO, composite video, 1.0 Vp-p, sync negative, 75

terminated

Pixel clock 12108 MHz

Vertical frequency 4585 Hz

Horizontal frequency 1570 kHz

Audio input signal ø3.5 mm minijack: AUDIO, 0.5 Vrms, more than 22 k

(stereo)

Speaker system 2.8 cm round

× 1

Rated voltage AC 100240 V

Input current 2.0 A

Rated frequency 50/60 Hz

Power consumption 195 W (Standard mode)/177 W (Eco/Quiet mode "On") with AC 100 V

190 W (Standard mode)/167 W (Eco/Quiet mode "On") with AC 240 V

Power consumption (standby) 4 W (AC 100 V) 5 W (AC 240 V)

Heat dissipation 730 BTU/hour (Standard mode)/660 BTU/hour (Eco/Quiet mode "On") with AC100 V

710 BTU/hour (Standard mode)/630 BTU/hour (Eco/Quiet mode "On") with AC240 V

Operating temperature 41°F to 95°F (+5°C to +35°C)

Storage temperature 4°F to 140°F (20°C to +60°C)

Cabinet Plastic

I/R carrier frequency 38 kHz

Dimensions (approx.) 9 47/

64" × 2

17/

32" × 4

13/

16" (247 (W) × 64 (H) × 122 (D) mm) (main body only)

9 47/

64" × 2

23/

32" × 4

13/

16" (247 (W) × 69 (H) × 122 (D) mm) (including adjustment foot and projecting parts)

Weight (approx.) 3.20 lbs. (1.45 kg)

Supplied accessories Remote control, Lithium battery, Power cord for U.S., Canada etc. (6 ', 1.8 m), Power cord for Europe,

except U.K. (6 ', 1.8 m), Power cord for U.K., Hong Kong and Singapore (6 ', 1.8 m), Power cord for

Australia, New Zealand and Oceania (6 ', 1.8 m), RGB/USB cable (6 ', 1.8 m), Cable tie

× 2, Soft case,

Projector manual CD-ROM, Operation manual

Replacement parts Lamp unit (Lamp/cage module) (AN-XR1LP), Remote control (RRMCGA256WJSA), Lithium battery,

Power cord for U.S., Canada etc. (QACCDA029WJPZ), Power cord for Europe, except U.K.

(QACCVA006WJPZ), Power cord for U.K., Hong Kong and Singapore (QACCBA015WJPZ), Power cord

for Australia, New Zealand and Oceania (QACCLA024WJPZ), RGB/USB cable (QCNWGA047WJPZ),

Cable tie (UBNDTA015WJZZ), Soft case (GCASNA011WJZZ), Projector manual CD-ROM

(UDSKAA045WJZZ), Opera-tion manual Except for XR-1SA (TiNS-B148WJZZ), Operation manual Only

for XR-1SA (TiNS-B251WJZZ)

As a part of policy of continuous improvement, SHARP reserves the right to make design and specification changes

for product improvement without prior notice.

The performance specification figures indicated are nominal values of production units. There may be some devia-

tions from these values in individual units.

XR-1S

IMPORTANT SERVICE SAFETY NOTES (for USA)

Ë Service work should be performed only by qualified service technicians who are

thoroughly familiar with all safety checks and servicing guidelines as follows:

WARNING

1. For continued safety, no modification of any circuit

should be attempted.

2. Disconnect AC power before servicing.

BEFORE RETURNING THE PROJECTOR:

(Fire & Shock Hazard)

Before returning the projector to the user, perform

the following safety checks:

1. Inspect lead wires are not pinched between the chassis

and other metal parts of the projector.

2. Inspect all protective devices such as non-metallic

control knobs, insulating materials, cabinet backs,

adjustment and compartment covers or shields,

isolation resistor-capacity networks, mechanical

insulators, etc.

3. To be sure that no shock hazard exists, check for

current leakage in the following manner:

» Plug the AC cord directly into a 120-volt AC outlet, (Do

not use an isolation transformer for this test).

» Using two clip leads, connect a 50k ohm, 10 watt

resistor paralleled by a 0.15µF capacitor in parallel

between all exposed metal cabinet parts and earth

ground.

» Use an AC voltmeter with sensitivity of 5000 ohm per

volt., or higher, sensitivity to measure the AC voltage

drop across the resistor (See Diagram).

» All checks must be repeated with the AC plug

connection reversed. (If necessary, a non-polarized

adapter plug must be used only for the purpose of

completing these checks.)

Any reading of 0.3 volts RMS (this corresponds to 0.2

milliamp. AC.) or more is excessive and indicates a

potential shock hazard which must be corrected before

returning the unit to the owner.

12345678901234567890123456789012123456789012345678901234567890121234567890123456789012345678901212

SAFETY NOTICE

Many electrical and mechanical parts in DMDTM

Projector have special safety-related characteristics.

These characteristics are often not evident from visual

inspection, nor can protection afforded by them be

necessarily increased by using replacement components

rated for higher voltage, wattage, etc.

Replacement parts which have these special safety

characteristics are identified in this manual; electrical

components having such features are identified by "å"

and shaded areas in the Replacement Parts Lists and

Schematic Diagrams. For continued protection,

replacement parts must be identical to those used in

the original circuit. The use of a substitute replacement

parts which do not have the same safety characteristics

as the factory recommended replacement parts shown

in this service manual, may create shock, fire or other

hazards.

AVIS POUR LA SECURITE

De nombreuses pièces, électriques et mécaniques, dans

les projecteur à DMDTM présentent des caractéristiques

spéciales relatives à la sécurité, qui ne sont souvent pas

évidentes à vue.

Le degré de protection ne peut pas être nécessairement

augmentée en utilisant des pièces de remplacement

étalonnées pour haute tension, puissance, etc.

Les pièces de remplacement qui présentent ces

caractéristiques sont identifiées dans ce manuel;

les pièces électriques qui présentent ces particularités

sont identifiées par la marque "å" et hachurées dans la

liste des pièces de remplacement et les diagrammes

schématiques. Pour assurer la protection, ces pièces

doivent être identiques à celles utilisées dans le circuit

d'origine. L'utilisation de pièces qui n'ont pas les mêmes

caractéristiques que les pièces recommandées par l'usine,

indiquées dans ce manuel, peut provoquer des

électrocutions, incendies ou autres accidents.

WARNING: The bimetallic component has the primary

conductive side exposed. Be very careful in

handling this component when the power is on.

AVERTISSEMENT: La composante bimétallique dispose du

conducteur primaire dénudé. Faire attention

lors de la manipulation de cette

composante sous tension.

DVM

AC SCALE

1.5k ohm

10W

TO EXPOSED

METAL PARTS

CONNECT TO

KNOWN EARTH

GROUND

0.15 µF

TEST PROBE

XR-1S

NOTE POUR LE PERSONNEL

D'ENTRETIEN

PRECAUTION POUR LES RADIATIONS UV

La source de lumière, la lampe UHP, dans le projecteur

LCD émet de petites quantités de radiation UV.

EVITEZ TOUTE EXPOSITION DIRECTE DES

YEUX ET DE LA PEAU.

Pour votre sécurité, nous vous prions de respecter

les points suivants:

1. Toujours porter des lunettes de soleil lors d'un entretien

du projecteur

avec la lampe allumée

et le haut du coffret retiré.

2. Ne pas faire fonctionner la lampe à l'extérieur du boîtier

de lampe.

3. Ne pas faire fonctionner plus de 2 heures avec le coffret

retiré.

Précautions pour les radiations UV

et la lampe moyenne pression

1. Toujours débrancher la fiche AC lors du remplacement

de la lampe.

2. Laisser l'unité refroidir pendant une heure avant de

procéder à l'entretien.

3. Ne remplacer qu'avec une lampe du même type. Type

AN-XR1LP, caractéristique 150W.

4. La lampe émet de petites quantités de radiation UV-

éviter tout contact direct avec les yeux.

5. La lampe moyenne pression implique un risque

d'explosion. Toujours suivre les instr uctions

d'installation décrites ci-dessous et manipuler la lampe

avec soin.

NOTE TO SERVICE

PERSONNEL

UV-RADIATION PRECAUTION

The light source, UHP lamp, in the LCD projector

emits small amounts of UV-Radiation.

AVOID DIRECT EYE AND SKIN EXPOSURE.

To ensure safety please adhere to the following:

1. Be sure to wear sun-glasses when servicing the

projector with the lamp

turned "on" and the top

enclosure removed.

2. Do not operate the lamp outside of the lamp housing.

3. Do not operate for more than 2 hours with the enclosure

removed.

UV-Radiation and Medium Pressure

Lamp Precautions

1. Be sure to disconnect the AC plug when replacing the

lamp.

2. Allow one hour for the unit to cool down before

servicing.

3. Replace only with same type lamp. Type AN-XR1LP

rated 150W.

4. The lamp emits small amounts of UV-Radiation, avoid

direct-eye contact.

5. The medium pressure lamp involves a risk of explosion.

Be sure to follow installation instructions described

below and handle the lamp with care.

123456789012345678901234567890121234567890123456