KENWOOD KAC-M845 - Owner's Manual Immediate Download

4/3/2 CHANNEL POWER AMPLIFIER

KAC-M845

KAC-M645

INSTRUCTION MANUAL

2 English

Safety precautions

2WARNING

To prevent injury or fire, take the following

precautions:

· When extending the ignition, battery, or ground

wires, make sure to use automotive-grade wires

or other wires with a 5 mm² (AWG 10) or more to

prevent wire deterioration and damage to the wire

coating.

· To prevent a short circuit, never put or leave any

metallic objects (such as coins or metal tools) inside

the unit.

· If the unit starts to emit smoke or strange smells,

turn off the power immediately and consult your

Kenwood dealer.

· Do not touch the unit during use because the

surface of the unit becomes hot and may cause

burns if touched.

· Mounting and wiring this product requires skills and

experience. For safety's sake, leave the mounting and

wiring work to professionals.

2CAUTION

To prevent damage to the machine, take

the following precautions:

· Be sure the unit is connected to a 12V DC power

supply with a negative ground connection.

· Do not open the bottom covers of the unit.

· Do not install the unit in a spot exposed to direct

sunlight or excessive heat or humidity. Also avoid

places with too much dust or the possibility of water

splashing.

· When replacing a fuse, only use a new one with the

prescribed rating. Using a fuse with the wrong rating

may cause your unit to malfunction.

· To prevent a short circuit when replacing a fuse, first

disconnect the wiring harness.

NOTE

· If you experience problems during installation,

consult your Kenwood dealer.

· If the unit does not seem to be working right,

consult your Kenwood dealer.

To prevent battery from running out

When the unit is used in the ACC ON position without

turning the engine ON, it depletes the battery. Use it

after starting the engine.

Cleaning the unit

If the front panel gets dirty, turn off the power and

wipe the panel with a dry silicon cloth or soft cloth.

2 CAUTION

Do not wipe the panel with a hard cloth or a cloth

dampened by volatile solvents such as paint thinner

and alcohol. They can scratch the surface of the panel

and/or cause the indicator letters to peel off.

Protection function

The protection function is activated in the following

situations:

This unit is equipped with a protection function for

protecting this unit and your speakers from various

accidents or problems that can occur.

When the protection function is triggered, the Power

indicator goes off and the amplifier stops operating.

· When a speaker wire may be short-circuited.

· When a speaker output contacts ground.

· When the unit malfunctions and a DC signal is sent

to the speaker output.

· When the internal temperature is high and unit

won't operate.

· When a ground wire of the center unit (cassette

receiver, CD receiver, etc.) or this unit is not

connected to a metal part serving as an electrical

ground passing electricity to the battery's negative

- terminal.

English

Installation

2 CAUTION

· Do not install in the below locations;

(Unstable location, In a location that interferes

with driving, In a location that gets wet, In a dusty

location, In a place that gets hot, In a place that gets

direct sunlight, In a location that gets hit by hot air)

· Do not install the unit under the carpet. Otherwise

heat build-up occurs and the unit may be damaged.

· Install this unit in a location which allows heat to

easily dissipate.

Once installed, do not place any object on top of the

unit.

· The surface temperature of the amplifier will become

hot during use. Install the amplifier in a place

where people, resins, and other substances that are

sensitive to heat will not come into contact with it.

· This unit has cooling fan to decrease the internal

temperature. Do not mount the unit in a place where

the cooling fan and ducts of the unit are blocked.

Blocking these openings will inhibit the cooling of

the internal temperature and result in malfunction.

· When making a hole under a seat, inside the trunk,

or somewhere else in the vehicle, check that there

is nothing hazardous on the opposite side such as a

gasoline tank, brake pipe, or wiring harness, and be

careful not to cause scratches or other damage.

· Do not install near the dashboard, rear tray, or air bag

safety parts.

· The installation to the vehicle should securely fasten

the unit to a place in which it will not obstruct

driving. If the unit comes off due to a shock and hits

a person or safety part, it may cause injury or an

accident.

· After installing the unit, check to make sure that

electrical equipment such as the brake lamps,

turn signal lamps and windshield wipers operate

normally.

Installation board, etc.

(thickness : 15 mm or more)

Self-tapping screw

(ø4 × 16 mm)

330 mm

236 mm

Ø4.6

218.4

230

Accessories

Part name

External

View

Number of

Items

Self-tapping screws

(ø4 × 16 mm)

Terminal cover

(Power terminal)

Speaker level input

cable

Cooling fan

(KAC-M845)

Cooling fan

(KAC-M845)

4 English

Controls

40W

15W

1 A ch FILTER switch

This switch allow filtering of the speaker output

signals.

· OFF position:

The original sound without filtering is output.

· HPF (High Pass Filter) position:

Only frequencies of 80 Hz or higher are output.

(Frequencies below 80 Hz are cut.)

2 B ch FILTER switch

This switch allow filtering of the speaker output

signals.

· OFF position:

The original sound without filtering is output.

· LPF (Low-Pass Filter) position:

The filter outputs the band of lower frequencies

than the frequency set with the "LPF

FREQUENCY" control.

The speaker output is automatically turned

monaural (L+R) and the gain is enhanced.

3 INPUT SENSITIVITY control (A.ch/ B.ch)

Set this control according to the pre-output level of

the center unit connected with this unit, or to the

maximum power output of the genuine-accessory

car stereo.

Use the diagram on the right as a guide.

The sensitivities of amplifiers A and B can be

adjusted independently.

4 B ch LPF FREQUENCY control

Sets the cutoff frequency when the "B ch FILTER"

switch is set to "LPF".

5 Power indicator

When the power is turned on, the Power indicator

lights.

If the Power indicator does not light when the

power is turned on, the protection function may be

activated. Check whether there is any indication of

trouble. Refer to <Protection function> (page 2).

English

Connection

Installation procedure

Since there are large variety of settings and

connections possible according to applications, read

the instruction manual well to select the proper

setting and connection.

1. Remove the ignition key and disconnect the

negative

- terminal of the battery to prevent short

circuits.

2. Set the unit according to the intended usage.

3. Connect the input and output wires of the units.

4. Connect the speaker wires.

5. Connect the power wire, power control wire and

grounding wire following this order.

6. Install the installation fittings in the unit.

7. Attach the unit.

8. Connect the negative

- terminal of the battery.

2 WARNING

To prevent fire caused by a short in the wiring,

connect a fusible link or breaker nearby the battery's

positive terminal.

2 CAUTION

· If sound is not output normally, immediately turn

power off and check connections.

· Be sure to turn the power off before changing the

setting of any switch.

· If the fuse blows, check wires for shorts, then replace

the fuse with one of the same rating.

· Check that no unconnected wires or connectors are

touching the car body. Do not remove caps from

unconnected wires or connectors to prevent short

circuits.

· Connect the speaker wires to appropriate speaker

connectors separately. Sharing the negative wire of

the speaker or grounding speaker wires to the metal

body of the car can cause this unit to fail.

· After installation, check that the brake lamps,

winkers, and wipers work properly.

Wiring

· Take the battery wire for this unit directly from the

battery. If it's connected to the vehicle's wiring

harness, it can cause blown fuses etc.

· If a buzzing noise is heard from the speakers when

the engine is running, connect a line noise filter

(optional) to each of the battery wire.

· Do not allow the wire to directly contact the edge of

the iron plate by using Grommets.

· Connect the ground wire to a metal part of the car

chassis that acts as an electrical ground passing

electricity to the battery`s negative

- terminal.

Do not turn the power on if the ground wire is not

connected.

· Be sure to install a protective fuse in the power

cord near the battery. The protective fuse should

be the same capacity as the unit's fuse capacity or

somewhat larger.

· For the power cord and ground, use a vehicle type

(fireproof ) power wring cord with a current capacity

greater than the unit's fuse capacity. (Use a power

wiring cord with a diameter of 5 mm² (AWG 10) or

greater.)

· When more than one power amplifier are going

to be used, use a power supply wiring wire and

protective fuse of greater current-handling capacity

than the total maximum current drawn by each

amplifier.

Speaker selection

· The input power of the speakers that are going to

be connected should be greater than the output

power (in Watts) of the amplifier. Use of speakers

having input power ratings that are less than the

output power of the amplifier will cause smoke to

be emitted as well as damage.

· The impedance of the speakers that are going

to be connected should be 2 or greater (for

stereo connections), or 4 or greater (for bridged

connections). When more than one set of speakers

are going to be used, calculate the combined

impedance of the speakers and then connect

suitable speakers to the amplifier.

Combined impedance