KENWOOD CCD-2000 - Owner's Manual Immediate Download

CCD-2000

UNIVERSAL REAR VIEW CAMERA

INSTRUCTION MANUAL

CAMERA DE VUE ARRIERE UNIVERSELLE

MODE D'EMPLOI

UNIVERSAL RÜCKFAHRKAMERA

BEDIENUNGSANLEITUNG

UNIVERSELE ACHTERUITRIJCAMERA

GEBRUIKSAANWIJZING

TELECAMERA PER RETROMARCIA UNIVERSALE

ISTRUZIONI PER L'USO

CÁMARA DE VISTA TRASERA UNIVERSAL

MANUAL DE INSTRUCCIONES

CÂMARA TRASEIRA UNIVERSAL

MANUAL DE INSTRUÇÕES

Take the time to read through this instruction manual.

Familiarity with installation and operation procedures will help you obtain the best

performance from your new Rear View Camera.

For your records

Record the serial number, found on the back of the unit, in the spaces designated on the

warranty card, and in the space provided below. Refer to the model and serial numbers

whenever you call upon your Kenwood dealer for information or service on the product.

Model CCD-2000 Serial number

US Residence Only

w w w.Kenwoodusa.com

2 | English

· Do not mount this unit near the heater outlet, where

it would be affected by heat, or near the doors, where

rainwater might splash onto it. (Never install in locations

such as the above because of the danger of malfunction

due to high temperatures.)

· Before drilling any mounting holes always check behind

where you want to drill the holes. Do not drill into the gas

line, brake line, electrical wiring or other important parts.

· If this unit is installed in the passenger compartment,

anchor it securely so it does not break free while the car is

moving, and cause injury or an accident.

· If this unit is installed under a front seat, make sure it does

not obstruct seat movement. Route all leads and cords

carefully around the sliding mechanism so they do not

get caught or pinched in the mechanism and cause a

short circuit.

Accessories

1 Power cord

..........1

2 Wiring harness

..........1

3 Camera bracket

..........1

4 Screw

..........2

2WARNING

To prevent injury or fire, take the

following precautions:

· To prevent a short circuit, never put or leave any metallic

objects (such as coins or metal tools) inside the unit.

· Installation and wiring of this product require specialist

skill and experience. To assure your safety, please request

a specialist technician to install the unit.

2CAUTION

To prevent damage to the product, take

the following precautions:

· Make sure to ground the unit to a negative 12V DC power

supply.

· When replacing a fuse, only use a new fuse with the

prescribed rating. Using a fuse with the wrong rating may

cause your unit to malfunction.

· Do not use your own screws. Use only the screws

provided. If you use the wrong screws, you could damage

the unit.

NOTE

· This product is a rear view camera for checking the view

at the rear of a car.

· A rear view camera is a camera that provides symmetrical

images in the same way as rear and side view mirrors.

· Connection to a TV with an RCA video input is possible,

but confirm whether the TV you use has a reverse gear

connection function.

· Direct sunlight or strong light (sunlight reflected from a

bumper etc.) on the camera may result in smear above

and below the location where the light strikes, but this is

not a malfunction.

· This product is designed to supplement the driver's rear

view, but the camera images do not show all dangers and

obstacles. Be sure to look behind you when reversing to

confirm the view.

· This product features a wide-angle lens, so the near view

is wide and the far view is narrow, which may create a

false sense of distance. Be sure to look behind you when

reversing to confirm the view.

· Do not wash your car with an automatic car wash or

high-pressure water as it may result in water entering the

camera or the camera falling off.

· Check camera bracket installation before driving.

Are the screws loose?

- Is the camera bracket firmly secured?

- If the rear view camera comes loose while you are

driving it may cause an accident.

· Before finally installing the unit, connect the wiring

temporarily, making sure it is all connected up properly,

and the unit and the system work.

· When mounting this unit, make sure none of the leads

are trapped between this unit and the surrounding

metalwork or fittings.

Before Use/ Accessories

English

Installation Procedure

1.To prevent a short circuit, remove the key from

the ignition and disconnect the

- battery.

2.Make the proper input and output wire

connections for each unit.

3.Connect the wiring harness wires in the following

order: ground, ignition, reverse and camera unit.

4.Connect the wiring harness connector to the

video box unit.

5.Install the unit in your car.

6.Reconnect the

- battery.

2WARNING

· If you connect the ignition wire (Red) to the car chassis

(Ground), you may cause a short circuit, that in turn may

start a fire. Always connect those wires to the power

source running through the fuse box.

· Do not cut out the fuse from the ignition wire (Red). The

power supply must be connected to the wires via the

fuse.

2CAUTION

· If your car's ignition does not have an ACC position,

connect the ignition wires to a power source that can be

turned on and off with the ignition key. If you connect the

ignition wire to a power source with a constant voltage

supply, as with battery wires, the battery may die.

· If the fuse blows, first make sure the wires aren't touching

to cause a short circuit, then replace the old fuse with one

with the same rating.

· Insulate unconnected wires with vinyl tape or other

similar material. To prevent a short circuit, do not remove

the caps on the ends of the unconnected wires or the

terminals.

· After the unit is installed, check whether the brake lamps,

blinkers, wipers, etc. on the car are working properly.

· Install so that it does not obstruct the rear field of view.

· Install so that it does not protrude from the side of the

car.

· Do not perform installation in rain or fog.

· When humidity is high, dry the surface to which the unit

is to be attached before installing.

· Moisture on the attachment surface reduces adhesive

strength, which may lead to the unit coming off.

· Do not attach the camera bracket to areas on the car

body treated with fluorocarbon resin, or glass.

· May result in the rear view camera falling off.

- Do not apply water to the unit.

- Do not expose the unit to rain.

- Do not subject the camera to unnecessary force.

- Thoroughly clean where tape is used for sticking on

the unit.

· Refer to the Instruction's manual for details on connecting

the other units, then make connections correctly.

· Secure the wiring with cable clamps or adhesive tape.

To protect the wiring, wrap adhesive tape around them

where they lie against metal parts.

· Route and secure all wiring so it cannot touch any

moving parts, such as the gear shift, handbrake and seat

rails.

· Do not route wiring in places that get hot, such as near

the heater outlet. If the insulation of the wiring melts or

gets torn, there is a danger of the wiring short-circuiting

to the vehicle body.

· When replacing the fuse, be sure to use only fuse of the

rating prescribed on the fuse holder.

· To minimize noise locate the TV antenna cable, radio

antenna cable and RCA cable as far away from each other

as possible.

· Do not install the video box unit in places where it may

become subject to high temperatures or humidity, such

as:

- Places close to a heater, vent or air conditioner.

- Places exposed to direct sunlight, such as on top of the

dashboard or the rear shelf.

- Places that may be splashed by rain, for example close

to the door.

4 | English

CAMERA

SRC

REVERSE

CAMERA

ACC

Ground wire (Black)

- (To car chassis) (1m)

Ignition wire (Red) (1m)

Ignition key switch

Car fuse box

(Main fuse)

ACC

Car fuse box

Battery

Video cable (1.5m)

If you connect the ignition wire (Red) to the car

chassis (Ground), you may cause a short circuit, that

in turn may start a fire. Always connect those wires

to the power source running through the fuse box.

Video Box Unit

Camera Unit

Connection

Monitor Unit (Optional)

Reverse sensor wire (Purple/White) (5m)

To vehicle's reverse lamp harness

To video input terminal

Camera cable (8m)

Power cord

(Accessory

Wiring harness

(Accessory

FUSE ( 2A )

English

Installation example

Install on the center part

Installation for Camera Unit

1 Clean the surface to which the rear view camera

is to be installed. Use a cloth or other item to wipe

oil, wax, dust and any other dirt from installation

surface.

2CAUTION

· Locate the rear view camera in the position you want it

installed. Adjust the angle of the rear view camera, and

install so that the camera doesn't touch the car.

· When sticking to a glass surface, stick it on in a position

that assures the camera doesn't touch the rear window.

2 Peel off the sheet on back of the camera bracket

(Accessory

3) and stick it on.

2CAUTION

· Press the camera bracket with your fingers to stick it to

installation surface. Touching the adhesive surface or

sticking the unit on a second time reduces adhesive

strength, which may result in the unit falling.

· If the temperature of the attachment surface is low,

warm with a hair dryer or other means before installing

to improve adhesive strength.

3 Attach the rear view camera to the camera

bracket (Accessory

3) with the installation screws

(Accessory

4).

2CAUTION

· The rear view camera is attached so that the logo of

Kenwood is on the upper surface.

4 Adjust the angle so that bumper or rear edge of

the car is displayed at the bottom of the monitor

screen.

Glass surface

Screw (Accessory

Camera bracket (Accessory

Monitor screen

Bumper or rear edge of car