JVC XMPX70PN - Owner's Manual Immediate Download

PORTABLE MINIDISC PLAYER

ENGLISH

*Use numbers indicated in parentheses when asking for replacement parts.

AC adaptor (AA-R9025) ............. 1 pc.

Headphones .................................. 1 pc.

Wired remote control .................. 1 pc.

Charger/adaptor (AC-R124) ...... 1 pc.

Dry-cell battery case .................... 1 pc.

Supplied Accessories

Check the packing carton for these accessories.

Thank you for purchasing this JVC product. Please read these instructions carefully before starting operation to be sure to obtain opti-

mum performance and a longer service life from your minidisc player.

INSTRUCTIONS

CAUTION!

THIS PRODUCT UTILIZES A LASER.

USE OF CONTROLS OR ADJUSTMENTS OR PERFOR-

MANCE OF PROCEDURES OTHER THAN THOSE

SPECIFIED HEREIN MAY RESULT IN HAZARDOUS

RADIATION EXPOSURE.

DO NOT OPEN COVERS AND DO NOT REPAIR YOUR-

SELF. REFER SERVICING TO QUALIFIED PERSONNEL.

WARNING:

TO REDUCE THE RISK OF FIRE OR ELECTRIC

SHOCK, DO NOT EXPOSE THIS APPLIANCE TO RAIN

OR MOISTURE.

Rechargeable nickel metal hydride battery (BN-R1210) ..... 1 pc.

Carrying pouch ......................................................................... 1 pc.

Using the rechargeable Ni-MH battery (included)

1 Remove the rechargeable battery from its case.

2 Insert the rechargeable battery into the charger/adaptor.

3 Set the switch on the charger/adaptor to "CHARGER".

4 Connect the AC adaptor to the charger/adaptor.

5 The charge indicator will initially light in red. It will go out when re-

charging is completed. When recharging is complete, unplug the

AC adaptor from the AC outlet and the charger/adaptor.

6 Remove the recharged battery from the charger/adaptor and insert

it into the minidisc player.

Notes:

· You cannot use the minidisc player while charging the rechargeable battery.

· It takes approximately 2 hours to recharge the rechargeable battery.

· The rechargeable battery has a service life of approximately 300 charge-discharge cycles. If

the operating time on one full charge becomes noticeably shorter than it used to be, the bat-

tery has reached the end of its service life and should be replaced.

· The AC adaptor and rechargeable battery may become warm while recharging. This is not a

malfunction.

· When recharging the rechargeable battery which was left unused for a long time, the charge

indicator may not light immediately. It will light in a few minutes.

Refer to the specifications for information on operating time durations when using a recharge-

able battery, dry-cell battery, a or both together.

Using the AC adaptor

CAUTION: Be sure there is no rechargeable battery in the minidisc

player.

1 Attach the battery case to the minidisc player.

Turn the knob on the battery case toward

"LOCK" until it stops. (To detach the bat-

tery case, turn the knob toward "RE-

LEASE" until the battery case comes

loose.)

2 Set the switch on the charger/adaptor to "ADAPTOR".

3 Connect the AC adaptor to the charger/adaptor, and the charger/

adaptor to the battery case.

Notes:

· The minidisc player is in standby mode when the AC adaptor and charger/adaptor are connected.

· The primary circuit is "live" as long as the AC adaptor is connected to an electrical outlet.

Cautions

Batteries

· Before replacing batteries, always turn the minidisc player off. Otherwise, the settings you

have made will be changed.

Rechargeable Ni - MH battery :

· Use only the rechargeable battery BN-R1210 (supplied) or BN-R127 (not supplied) with this

minidisc player.

· If the power delivered by the battery lasts for a very short time after recharging, it means

that the battery's service life is over. Do not use it any more.

· Recharging an already charged battery will shorten its service life.

· When recharging a battery for the first time, or when it has not been used for a long period

of time, the play time may be shorter than usual. In a case like this, repeatedly recharge and

discharge the battery. This will restore it to its regular state.

· Do not allow any metal objects to touch the terminals of the rechargeable battery because

this may cause dangerous short-circuiting.

· Recharge the battery at a temperature of 10°C to 35°C.

· Do not charge for more than 15 hours. Overcharging will shorten battery life.

· Charge at least once every 6 months when not using for long periods of time, to avoid a drop

in battery recharging performance

Dry cell battery and rechargeable battery:

To prevent damage to the batteries, and to avoid electrolyte leakage, heed the following instructions.

· Align the

ª and · polarities properly when inserting the batteries.

· Remove the batteries if you do not plan to use the minidisc player for a long period of time.

· Do not expose the batteries to open flame, and do not short-circuit, disassemble, or subject

them to excessive heat.

· Do not attempt to recharge dry cell batteries.

Carrying batteries:

· When putting dry cell or rechargeable batteries in a pocket or bag, ensure that no other metal

objects, such as necklaces or coins, are placed together with them. Contact with metal may

cause short-circuiting which, in turn, may cause a fire.

· Be absolutely sure to carry the rechargeable battery in the battery carrying case.

Recycling Notice

The rechargeable battery is designated recyclable.

Please follow your local recycling regulations.

AC adaptor and charger/adaptor

· Handle the AC adaptor and charger/adaptor carefully. Improper handling is dangerous.

· Do not touch them with wet hands.

· Do not place heavy objects on top of them.

· Do not forcibly bend them.

· Be sure to use only the AC adaptor and charger/adaptor provided with this minidisc player.

· Disconnect the AC adaptor from the power outlet if the unit is not going to be used for a

long time.

Power Supply Preparations

A OPEN knob

B Headphones jack ( )

C HOLD / SEARCH/

VOL (Volume) Mode switch

D Volume and Skip / SEARCH button

(+, ,

4, ¢ )

E Play / Pause / Stop button (

38/7)

F HOLD switch

G Display

Location of Controls

H Play / Pause button (

3/8)

I VOLUME button (+, )

J Skip / SEARCH button (

4 ¢ )

K DISP. (Display) button

L P.MODE(Play mode) button

M A.C.BASS (Active Clear Bass)

button

N Stop button (

[Indicators on the remote control display]

CLASS

LASER

PRODUCT

1. CLASS 1 LASER PRODUCT

2. CAUTION: Invisible laser radiation when

open and interlock failed or defeated.

Avoid direct exposure to beam.

3. CAUTION: Do not open the top cover.

There are no user serviceable parts

inside the Unit; leave all servicing to

qualified service personnel.

LVT0592-001B [UB]

Using a dry-cell battery (not included)

1 Open the lid of the battery case and insert a LR6 (UM-3) alkaline battery into the bat-

tery compartment.

2 Attach the battery case to the minidisc player. (See "Using the AC adaptor".)

Note:

· To lengthen battery life, you can use both the rechargeable battery and a dry-cell battery at

the same time.

HOLD SEARCH VOL

[Minidisc Player Unit]

Disc indicator

TRAIN

Random MANUAL Mode

Battery

1.5V

RELEASE

LOCK

1.5V

Battery case

If the rubber holder on the remote control clip comes off

Insert the clip into the rubber holder, then rotate the clip.

Rechargeable battery

Charger/Adaptor

(rotate)

[Remote Control]

DISP. P.MODE

VOLUME

A.C.BASS

[Remote control]

Rotate

Headphones cord

Rubber holder

Clip

Minidisc Player Unit

· Do not alter or remodel the unit as this can cause malfunctioning.

· Do not alter or impact the unit as this may damage it.

· Avoid using the unit in the following locations since they can cause malfunctioning.

1. Bathrooms and other moisture-prone places.

2. Warehouses and other dusty places.

3. Very hot places near heating appliances, etc.

· Do not leave the unit exposed to direct sunlight for long periods of time as this may deform

or discolor the cabinet and may also cause malfunctioning.

Precautions for listening with the headphones

· Do not play your headset at a high volume. Hearing experts advise against continuous ex-

tended play.

· If you experience a ringing in your ears, reduce volume or discontinue use.

· Do not use while operating a motorized vehicle. It may create traffic hazard and is illegal in

many areas.

· You should use extreme caution or temporarily discontinue use in potentially hazardous

situations.

· Even if your headphones are an open-air type designed to let you hear outside sounds, don't

turn up the volume so high that you can't hear what's around you.

When driving a car

· In the interest of traffic safety, do not use the minidisc player while driving a vehicle.

Battery Indicator

The battery indicator appears on the remote control display. When the indicator appears as be-

low, power will be shut off a short while after.

Rechargeable battery: Recharge it.

Dry-cell batter

y: Replace it with new one.

Note:

· While "No Disc" in displayed, the battery indicator does not changed. Actval indication will

be mode when an MD is inserted.

WARNING LABEL, PLACED

INSIDE THE UNIT

CAUTION:

AC adaptor (AA-R9025), Charger/Adaptor (AC-R124) and re-

chargeable Ni-MH battery (BN-R1210 and BN-R127) are audio

equipments for XM-PX70 only.

HOLD SEARCH VOL

[Unit (Bottom view)]

Repeat

* This unit has been manufactured with great precision.

Applying a strong shock to the unit or dropping it may

cause a failure: For example, if you sit down with the

unit into a back pocket of your trousers, it may exert the

pressure upon the unit and may cause a failure.

For remote

control

For minidisc

player unit

AC adaptor

Charge indicator

Charger/Adaptor

Knob

RELEASE

LOCK

1.5V

Battery case

Maintenance

Unit:

Wipe the unit and remote control with a soft cloth. Remove stubborn dirt using a cloth which

has been dipped in water (or soapy water) and wrung out. Then wipe them dry.

· If you intend to use a chemically treated cleaning cloth, read its directions first.

· Do not use alcohol or paint thinners.

MDs:

If the MD cartridge is dirty wipe it with a damp cloth and then wipe dry.

When storing MDs, avoid locations which are

· Exposed to direct sunlight.

· Susceptible to high levels of humidity or dust.

· Directly exposed to heat from a heating appliance.

· On top of a car dashboard or near the rear window.

Handling the MDs

· Do not open the shutter. The shutter is usually locked to prevent opening. Do not force in to

open, or the disc may be destroyed.

To AC power outlet

Battery case

OPEN

1.5V

AC adaptor

Charger/Adaptor

Slide the cover and

open it.

Insert the battery with its

positive terminal facing

out.

Firmly close the cover.

A.C. BASS

XM-PX70WT

XM-PX70BU

XM-PX70PN

* MDLP features a new sound compression method (ATRAC3) and a 2 times (or 4 times) long-

hour stereo recording and playing function.

The MDLP logo is marked on the MD recorders and players compatible with MDLP. It is also

marked on MDs prerecorded in ATRAC3 (excluding recordable MDs).

* Do not block the ventilation opening or holes. (If the ventilation openings of holes are blocked by

a newspaper or cloth, etc., the heat may not be able to get out.)

Do not place any naked flame sources, such as lighted candles, on the apparatus.

When discarding batteries, environmental problems must be considered and local rules or laws

governing the disposal of these batteries must be followed strictly.

Do not use this apparatus in a bathroom or places with water. Also do not place any containers

filled with water or liquids ( such as cosmetics or medicines, flower vases, potted plants, cups,

etc. ) on top of this apparatus.

Accidental Operation Prevention Function

(Hold Mode)

This function prevents the minidisc player from operating accidentally.

Both minidisc player and remote control have HOLD switches to set in HOLD mode, each of

which works independently.

· Slide the HOLD switch in the direction shown by the arrow to activate it.

· Rotate the remote control switch in the direction shown by the arrow to set the remote con-

trol in HOLD mode.

In HOLD mode, no button operation is possible.

To operate the minidisc player or remote control normally

, switch off the HOLD mode.

XM-PX70[U](Eng.)

12/18/00, 9:13 AM

Using the minidisc player with an audio system

You can listen to MDs through your audio system.

· After turning off the amplifier, plug a stereo connection cable (not supplied) into the head-

phones jack as shown below.

· Adjust the volume of the minidisc player to an appropriate level.

· Adjust the volume level on the amplifier.

· Use the unit's buttons for operation. (The remote control will issue a Pip tone.)

· Direct connection without passing through the remote control may generate noise.

Using the minidisc player with a car audio system

You can listen to an MD through your car audio system. The following accessories are avail-

able for your car audio system.

· Car adaptor (CA-R153)

· Car audio cassette adaptor

CAUTION:

Before connecting the car adaptor, remove the rechargeable battery from the unit and

the alkaline battery from the battery case.

· Connect the car adaptor to the battery case as shown below.

· Connect the car audio cassette adaptor to the remote control headphone jack.

The other end connects to the cassette slot of your car.

· Adjust the volume level of the unit to an appropriate level.

Notes:

· Since the insertion direction of the car audio cassette adaptor is limited, be sure that it can be

inserted into the cassette slot of your car audio system.

· Depending on the vehicle used, noise may occur. In this case, it is recommended to connect a noise

filter (available on the market) between the remote control and the car audio cassette adaptor.

· If your car audio system is equipped with a LINE IN or AUX IN jack, you can connect the

output of the remote control to the jack using a stereo mini plug signal cord (not supplied).

In this case, you do not need the optional car audio cassette adaptor.

Operation

Fast forward/

Reverse

Button

Skip function

Press during play back or while in Stop mode.

Search function

Keep depressed during play.

Button

Operation

To pause play

To stop play

To turn off the unit

(Off mode)

· During Random Play, the skip but-

tons cannot be used to skip back to

tracks that were played previously

in the random sequence.

Press during play.

Press again to restart play.

If paased for 2 minutes, the power will

automatically shut off.

Display/Reference

Blinks

Press the

3/8 (or 38/7) button again to restart

play (Resume Play). The current track will be

played from the beginning (see "Resume Play").

If stopped for 45 seconds, the power will

automatically shut off.

When all the music is played, the MD

player automatically stops.

Display/Reference

Repeat Play and Random Play

You can select either Repeat Play or Random Play. In Repeat Play, you can repeat all the

tracks, or an individual track, as many times as you like. In Random Play, you can play all the

tracks in random order.

Selecting Repeat Play and Random Play in Stop mode

In Stop mode, press the P.MODE button. Each time you press the button, the play mode

changes as follows:

P1 = P = RND = P1 RND = P RND = Original display = (back to the beginning)

: Repeats 1 track.

: Repeats all the tracks.

RND

: Random play

P1 RND : Repeats one track randomly selected.

P RND : Repeats all the tracks in random order.

After selecting one of the above modes, press the

3/8 (or 38/7) button.

To exit Repeat Play or Random Play,

stop the MD and then press the P.MODE button until

the display returns to its original setting.

Repeat Play during Playback

During Normal Play:

Each time you press the P.MODE button, the play mode changes as follows:

P1 = P = Original display = (back to the beginning)

Select "

P1" to repeatedly play the current track. Select "P" to repeat all the tracks.

During Random Play:

Each time you press the P.MODE button, the play mode changes as follows:

P1 RND = P RND = Original display = (back to the beginning)

Select "

P1 RND" to repeatedly play a randomly selected track. Select "P RND" to repeat all

the tracks in random order.

To exit Repeat Play or Random Play,

stop the MD and then press the P.MODE button until

the display returns to its original setting.

Selecting the Operational Options of Remote Control

Troubleshooting Guide

Before requesting service for this minidisc player, check the chart below for a possible cause of

the problem you are experiencing. Some simple checks, or a minor adjustment on your part,

may eliminate the problem and restore proper operation.

If you are in doubt about some of the check points, or if the remedies indicated in the chart do

not solve the problem, refer to the directory of Authorized Service Centers (enclosed with this

minidisc player), or consult your dealer for instructions.

Problem

Does not operate.

Cannot play the MD.

Tracks on MD do not play in or-

der, starting with the first track.

Cannot hear music--too noisy.

TV picture is distorted.

Radio reception is noisy.

Power is not turned on.

Charging indicator does not light

during charging.

Check this

Is the MD loaded? If unloaded, "No Disc" will appear on

the display.

· Is the HOLD switch released?

· Is the battery low?

· Is there moisture condensation on the lens?

(Wait for about an hour and then try again.)

· Is the Repeat Play or Random Play selected?

· You stopped or turned off the power while playing. It

changed to Resume Play.

· Is the headphone plug inserted all the way?

· Is the plug dirty? (Wipe away dirt on the plug.)

· Is music recorded on the MD? If not, "BLANK" will

appear on the display.

· Is the unit too near a TV or tuner? (If the TV or tuner is

connected to a simple indoor antenna, connect it to an

outdoor antenna.)

· With both HOLD switches activated, the battery was

changed during playback. (Release both HOLD switches

and try to operate again.)

· Is the charger too hot?

(If so, disconnect the AC adaptor and leave the charger

for a while.)

Specifications

Portable MINIDISC player

Type

: Minidisc digital audio system

Sampling frequency

: 44.1 kHz

Audio compression

system

: ATRAC/ATRAC 3 (

)

Number of channels

: 2 channels (stereo)

Frequency response

: 20 Hz to 20 000 Hz

Wow & flutter

: Unmeasurable

Output

: Headphone (3.5 mm dia. stereo

× 1)

5 mW/ch at 10% THD/16 ohms to 47 kohms

Muting the pip tone

When you press a button on the remote control ex-

cept for the A.C.BASS and VOLUME (+, ) buttons,

a pip tone is emitted.

To mute the pip tone,

while pressing the A.C.BASS

button in Stop mode or during playback, press the

P.MODE button. "BEEP OFF" appears on the remote control display.

To resume the pip tone,

do the same operation again. "BEEP ON" will appear on the display.

Changing the display character contrast

The character display contrast can be adjusted when

the characters become less clear due to ambient

temperature or during scrolling.

While pressing the A.C.BASS button in Stop mode or

during playback, press the SEARCH button.

Adjustment can be made between LCD00 and

LCD15. While the SEARCH button is pressed, the

contrast will be changed continuously. The initial

setting is "LCD07."

Using the Minidisc Player with Optional Accessories

(Stop mode)

Normal Play

Follow the numbers in the figure to the right.

1 Connect the headphones plug firmly.

2 Connect the remote control plug firmly.

The unit might turn on. However, when you leave the unit as it, it will automatically turn off.

3 Make sure the switches on the unit and remote control are not on

HOLD setting.

4 Load an MD.

· Slide the OPEN knob to open the lid.

· Open the lid by hand.

· Insert the MD into the MD slot beneath the lid, with its label side facing up. Insert the

MD until it stops. Be sure the

% or ] mark on the MD aligns as shown in the figure.

· Close the lid.

"HELLO" appears on the remote control display. Then the track number and playback

time appear after "T. READ" has gone out.

5 Adjust the volume level between 0 and 25.

Press the Volume (+, ) button on the unit or the remote control.

6 After "HELLO" disappears, press the 3/8 button on the remote control or

the

38/7 button on the unit.

Playback starts from the first track and ends after playing all the tracks on the MD.

Notes:

· Insert the MD in the way that it will not touch the catch. If the catch is bent for some reason,

the lid may not be closed properly.

· When opening the lid, please hold it by the edge when an MD is already loaded.

· If no MD is loaded, "No Disc" appears on the display, and the power will automatically shut

off after approx. 10 seconds.

· If the track has a title, the title will appear first.

ENGLISH

Resume Play

This function allows you to listen from the beginning of the track on which play was stopped

when the minidisc player was set to Stop mode.

Press the

3/8 (or 38/7) button.

Showing the Disc Information

Each time you press the DISP. button while in Stop

mode or during playback, the MD's information is

displayed as follows.

In Stop mode:

Disc title*

= Total number of tracks and total playback time of the MD = Track title* = Play-

back time

= (back to the beginning)

During Playback:

Playing time

= Track title* = (back to the beginning)

*The disc title or track title will scroll if it consists of 7 characters or more. If no title is given,

" ~" appears on the display. (Up to 80 characters can be displayed.)

In the case of 2 times long-hour playback

[Remote control]

[Unit]

[Remote control]

DISP. button

DISP.

P.MODE

VOLUME

DISP.

P.MODE

VOLUME

HOLD SEARCH VOL

Stereo connection

cable (not supplied)

Amplifier

Car adaptor (CA-R153)

Car audio cassette

adaptor (3.5 mm dia.

stereo plug)

Battery case

[Remote control]

[Unit]

Stereo long-hour playback

The unit supports

. So the unit can play any MD recorded in SP, LP2 or LP4 mode.

When a MD recorded in LP2 or LP4 mode is played, "LP2" or "LP4" indicator lights up on the

display. ("SP" is not displayed.)

SP : Standard stereo playback (Max. 80 minutes in MD 80)

LP2 : 2 times long-hour playback (Max. 160 minutes in MD 80)

LP4 : 4 times long-hour playback (Max. 320 minutes in MD 80)

· MDs recorded by the MD recorder that do not

support

are played in standard (SP)

mode.

Put the labeled side up.

rotate

MD Messages:

Messages

Meaning

Action

DISC ERROR

There is a problem (damage) with the disc.

Replace the disc.

READ ERROR

Cannot read data.

Remove the MD and

reinsert it.

The power is shut off after "BYE" ap-

pears on the display.

To turn on the unit, press the

3/8

(or

38/7) button.

(Blank)

[Unit]

[Remote control]

HOLD SEARCH VOL

1000MNMCREJES

Stops

Catch

Contrast

is up

Contrast

is down

Changing the Sound (A.C.BASS)

Each time you press the A.C.BASS button, the sound mode name and the indicator shown on

the display change as follows:

A.C.BASS

ON: The A.C.BASS (Active Clear Bass) function

is enabled and the bass level is automatically

controlled in conjunction with the sound

volume.

ON: The amount of sound leaking from the head-

phones will be reduced.

ON: You can use the adjusted tone. To adjust the

tone, see "Adjusting Tone in MANUAL

Sound Mode".

(Original display)

To cancel every function,

press the A.C.BASS button until the display returns to the original one.

Adjusting Tone in MANUAL Sound Mode

You can adjust the tone by changing the bass and treble.

1 Press the A.C.BASS button until "MANUAL" ( ) appears on the

display. (If the indicator is already lit, you can skip this step.)

2 Press the A.C.BASS button for 2 seconds or more within 8 sec-

onds. The following tone level meter appears.

3 To change the bass level, press the button. The bass level bar

blinks. Then, press the VOLUME + or button within 16 seconds to

move the bass level bar up or down (in 3 steps each).

To change the treble level, do the same except for pressing the button. The tone level set

here is stored in memory.

To exit tone adjusting mode,

wait until the display automatically returns to the original

one, or press the A.C.BASS button until the display returns to the original one.

A.C.BASS

VOLUME

Press for 1 second or

more.

Just Press.

In play mode, press for 1 second or more.

DISP.

P.MODE

VOLUME

· To eject the MD, slide the OPEN knob and open the lid by hand. The MD will then come out.

· When the remote control is connected, the power may automatically turn on. However, if

left as it is, it will eventually turn off automatically.

· This MD Player has a 40 second (SP mode) sound-skip-guard memory function to

accomodate any shocks. Consequently, it can be used while walking.

(For 2 seconds)

Bass level bar

Treble level bar

Fixed bar

(flat level)

Power requirements

: DC 1.2 V (rechargeable battery), DC 1.5 V (R6 size battery)

DC IN 1.5 V

Dimensions (L

× W × H) : 78 mm × 14.6 mm × 71 mm

(Excluding buttons and controls)

Mass

: Approx. 57 g (without battery)

AC adaptor (AA-R9025)

Charger/adaptor (AC-R124)

Input power source : AC 230 V, 50 Hz

Input power source

: DC 9 V, 0.5 A

Output voltage

: DC 9 V, 0.5 A

Output voltage

: DC 1.5 V, 0.7 A

Design and specifications are subject to change without notice.

US and foreign patents licensed from Dolby Laboratories Licensing Corporation.

Duration of battery:

Continous playback time*

Volume level: VOL 12

SP mode

LP2 mode

LP4 mode

Rechargeable battery (BN-R1210)

25 hours

31 hours

36 hours

Rechargeable battery (BN-R127)

22 hours

28 hours

32 hours

Alkaline battery (LR6)

42 hours

52 hours

60 hours

BN-R1210 + LR6

70 hours

86 hours

100 hours

* Approx. playback time is listed. The time may differ depending on the ambient tempera-

ture, usage condition, battery manufacture, kind of battery, etc.

The disc indicator rotates

Number of tracks being played

Playing time

(Within one second)

(Within one

second)

XM-PX70[U](Eng.)

12/18/00, 9:13 AM