background image
5
1
6
XL-PG300A/XL-PG300B/XL-PG300Y / LVT1178-001A / J,C,UJ
XL-PG300A/XL-PG300B/XL-PG300Y / LVT1178-001A / J,C,UJ
XL-PG300A/XL-PG300B/XL-PG300Y / LVT1178-001A / J,C,UJ
p6
p1
p5
Stereo headphones .......................................................................................................................... 1 pc.
Supplied Accessories
Concerning Compact Discs
PORTABLE CD PLAYER XL-PG300A/XL-PG300B/
XL-PG300Y
INSTRUCTIONS
Thank you for purchasing this JVC product. Please read these instructions carefully before starting
operation to be sure to obtain optimum performance and a longer service life from the unit.
Only compact discs bearing this mark can be used with this unit.
However, continued use of irregular shape CDs (heart-shape, octagonal, etc.) can damage
the unit.
If moisture has formed on a disc
When moisture has formed because the
disc was brought suddenly into a warm
room from a cold environment, wipe off
the moisture using a soft dry cloth.
When storing discs
Avoid locations which are
· Exposed to direct sunlight.
· Susceptible to high levels of humidity or
dust.
· Directly exposed to heat from a heating
appliance.
· On top of a car dashboard or near the
rear window.
Handling precautions
· On the label side (the side with writing)
Do not write anything using a pencil,
ball-point pen, etc. Do not use adhesive
paper or labels.
· On the disc (shiny) side
Handle this side carefully to keep it free
from fingerprints or scratches. Do not
use record cleaners, solvents, etc.
· Do not attach labels or stickers to CDs.
Do not use CDs with exposed adhesive
from tape or left over peeled off stickers.
· Do not use scratch-proof protectors or
covers other than those specified for use
with this unit.
If the disk surface is dirty
Wipe it with a damp cloth and then wipe dry.
Wipe from the center toward the outer edge.
How to hold a disc
How to store the disc in
its case
How to remove a disc from its case
Label side up
LVT1178-001A [J,C,UJ]
CD-R and CD-RW discs recorded with the audio
CD format can be played back, though some may
not be played back because of the disc character-
istics or recording condition.
Play surface (shiny surface)
For Customer Use:
Enter below the Model No. and Serial
No. which are located either on the rear,
bottom or side of the player. Retain this
information for future reference.
Model No.
Serial No.
EN
0204SKMCREORI
©2004 VICTOR COMPANY OF JAPAN, LIMITED
Put the grip band on your hand
Adjust the grip band to your hand size.
Unit
Wipe the unit with a soft cloth. Remove stubborn dirt using a cloth which has been dipped in wa-
ter or soapy water and wrung out, and then wipe dry.
· If you intend to use a chemically treated cleaning cloth, read its directions first.
· Do not use alcohol or paint thinners.
Lens
Maintenance
Air blower for
camera lens
Lens
Precautions
Safety
1. Care of AC adaptor
- The cord of the AC adaptor should be
routed so that they are not likely to be walked on or pinched by
items placed upon or against them. Never take hold of the AC
adaptor if your hand is wet, and always grasp the plug when
connecting or disconnecting it.
2. Disconnect when not in use
- When not in use, be sure to dis-
connect the AC adaptor from the AC power outlet.
3. Batteries
- If the unit is not used for a long period of time or is
used only from an AC power source, remove all the batteries to
prevent potential damage due to battery leakage. Do not mix
(old and new ) batteries or different types of batteries.
Installation
I Environment
1. Condensation
- Moisture may form on the lens in the follow-
ing conditions...
· immediately after a heater has been turned on.
· in a steamy or very humid room.
· when the unit is suddenly moved from a cold environment to
a warm one. If moisture forms inside this unit, it may not op-
erate properly. To correct this problem wait about one hour
for the moisture to evaporate.
I Placement
1. Foreign Material
- Care should be taken so that objects do not
fall into and liquids are not spilled into the unit. Do not subject
this unit to excessive smoke, dust, mechanical vibration, or
shock.
2. Magnetism
- The unit should be situated away from equipment
or devices that generate strong magnetic fields.
3. Stacking
- Do not place any objects on top of the unit.
Maintenance
(See page 5 for details.)
Clean the cabinet, panel and controls with a soft cloth lightly
moistened with mild detergent solution.
Do not use any type of abrasive pad, scouring powder or solvent
such as alcohol or benzine.
Service
1. Damage Requiring Service
- The unit should be serviced by
qualified service personnel when:
(a) The AC adaptor is damaged; or
(b) Objects have fallen or liquid has been spilled into the unit; or
(c) The unit has been exposed to rain; or
(d) The unit does not appear to operate normally or exhibits a
marked change in performance; or
(e) The unit has been dropped, or the enclosure damaged.
THE FOLLOWING NOTICES ARE APPLIED ONLY FOR THE U.S.A.:
CAUTION!
THIS PRODUCT UTILIZES A LASER.
USE OF CONTROLS OR ADJUSTMENTS OR PERFORMANCE
OF PROCEDURES OTHER THAN THOSE SPECIFIED HEREIN
MAY RESULT IN HAZARDOUS RADIATION EXPOSURE.
DO NOT OPEN COVERS AND DO NOT REPAIR YOURSELF.
REFER SERVICING TO QUALIFIED PERSONNEL.
CAUTION!
This equipment has been tested and found to comply with
the limits for a Class B digital device, pursuant to Part 15 of
the FCC Rules.
These limits are designed to provide reasonable protection
against harmful interference in a residential installation. This
equipment generates, uses and can radiate radio frequency
energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio com-
munications. However, there is no guarantee that interfer-
ence will not occur in a particular installation. If this
equipment does cause harmful interference to radio or televi-
sion reception, which can be determined by turning the
equipment off and on, the user is encouraged to try to correct
the interference by one of the following measures:
· Reorient or relocate the receiving antenna.
· Increase the separation between the equipment and re-
ceiver.
· Connect the equipment into an outlet on a circuit different
from that to which the receiver is connected.
· Consult the dealer or an experienced radio/TV technician
for help.
Any unauthorized changes or modifications to this equip-
ment would void the user's authority to operate this device.
WARNING:
TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO
NOT EXPOSE THIS APPLIANCE TO RAIN OR MOISTURE.
CAUTION:
· Do not block the ventilation opening or holes. (If the venti-
lation openings of holes are blocked by a newspaper or
cloth, etc., the heat may not be able to get out.)
· Do not place any naked flame sources, such as lighted
candles, on the apparatus.
· When discarding batteries, environmental problems must
be considered and local rules or laws governing the dis-
posal of these batteries must be followed strictly.
· Do not expose this apparatus to rain, moisture, dripping or
splashing and that no objects filled with liquids, such as vases,
shall be placed on the apparatus.
This Class B digital apparatus complies with Canadian
ICES-003.
Cet appareil numérique de la classe B est conforme à la
norme NMB-003 du Canada.
Check this
· Is the AC adaptor securely connected?
· Is the HOLD switch set to OFF position?
Is the disc properly secured in place?
· Is the disc properly secured in place?
· Is there moisture condensation on the lens?
(Wait for about an hour and then try again.)
· Is the headphone plug inserted all the way?
· Is the plug dirty? (Wipe away dirt on the plug.)
Are you using the unit too near a TV or tuner? (If the TV or
tuner is connected to a simple indoor antenna, connect it to
an outdoor antenna.)
· Is the disc damaged?
· Is the disc playable on this player?
· Has the disc been inserted upside down?
Problem
Does not turn on.
Cannot close the lid.
Cannot play discs.
Cannot hear music--too
noisy.
TV picture is distorted.
Radio reception is noisy.
"dISC" or "Er" is displayed
when a disc is in the
player.
Troubleshooting
If the remedies indicated in the chart do not solve the problem, refer to the directory of Autho-
rized Service Centers (enclosed with this unit) to locate a convenient service center, or consult
your dealer for instructions.
Portable CD player
Type
: Compact disc player
Signal detection system : Non-contact optical pickup (semiconductor laser)
Pickup system
: 3 beam laser
Number of channels:
: 2 channels (stereo)
Frequency response
: 20 Hz to 20 kHz
Wow & flutter
: Unmeasurable
Output
: Headphones (3.5 mm dia. stereo
× 1)
9 mW/ch at 10 % THD/16
matching impedance (16 to 1 k)
Duration of battery
: Approx. 30 hours when using two alkaline batteries (LR6)
(with Anti-Shock
Protection EX OFF)
Power requirements
: DC 3 V ("AA" or "R6" size battery
× 2)
DC 2.4V (rechargeable battery
× 2)
DC IN 4.5 V
Dimensions (W
×H×D) : 133.2 mm ×30.8 mm × 146.8 mm (5- 1/4" × 1- 1/4" × 5- 13/16")
(Excluding buttons and controls)
Mass
: 250 g (0.56 lbs)
(with grip band, without batteries)
AC adaptor (not supplied)
Input power source
: AC 120 V, 60 Hz (for the U.S.A. and Canada)
AC 110V - 127V/220 V - 240V, 50/60 Hz (for multi voltage area)
Output voltage
: DC 4.5 V, 600 mA
*
Design and specifications are subject to change without notice.
Specifications
Cautions
Listening precautions
Do not play your headphones or earphones at a high volume.
Hearing experts advise against continuous extended play.
If you experience a ringing in your ears, reduce volume or discon-
tinue use.
Do not use while operating a motorized vehicle. It may create a
traffic hazard and is illegal in many areas.
You should use extreme caution or temporarily discontinue use
in potentially hazardous situations.
Even if your headphones or earphones are an open-air type de-
signed to let you hear outside sounds, don't turn up the volume
so high that you can't hear what's around you.
Sound can be deceiving. Over time your hearing "comfort level"
adapts to higher volumes of sound. So what sounds "normal" can
actually be loud and harmful to your hearing.
Guard against this by setting your equipment at a safe level BE-
FORE your hearing adapts.
To establish a safe level:
· Start your volume control at a low setting.
· Slowly increase the sound until you can hear it comfortably and
clearly, and without distortion.
Once you have established a comfortable sound level:
· Set the dial and leave it there.
Rechargeable batteries
· Rechargeable batteries (not supplied) can be used.
· To use the rechargeable batteries, follow the instruction manual
attached to the rechargeable batteries and charger (not sup-
plied).
Dry cell batteries
To prevent damage to the batteries and electrolyte leakage, heed
the following points.
· Align the , and . polarities properly when inserting the bat-
teries.
· Do not mix different types or makers of batteries or old and
new batteries.
· Remove the batteries if you do not plan to use the unit for a
long period of time.
· Do not throw batteries into a fire, and do not short-circuit, dis-
assemble or subject them to excessive heat.
· Do not attempt to recharge dry cell batteries.
Carrying dry cell batteries around
When putting dry cell batteries in a pocket or bag, ensure that no
other metal objects such as a necklace are placed together with
them. Contact with metal may cause short-circuiting which, in
turn, may cause a fire.
AC adaptor
· Handle the AC adaptor carefully. Improper handling is dan-
gerous.
· Do not touch it with wet hands.
· Do not place heavy objects on top of it.
· Do not forcibly bend it.
· Be sure to connect only the specified AC adaptor with the unit.
· Disconnect the AC adaptor from the power outlet if the unit is
not going to be used for a long time.
Unit
No altering or remodeling
This can cause malfunctioning.
No dropping or strong impacts
This may damage the unit.
Locations to be avoided
Avoid using the unit in the following locations since they can
cause malfunctioning.
1. Bathrooms and other moisture-prone places.
2. Warehouses and other dusty places
3. Very hot places near heating appliances, etc.
Do not leave the unit exposed to direct sunlight for
long periods of time
This may deform or discolor the cabinet and may also cause mal-
functioning.
When purchasing AC adaptor /
AC plug adaptor
Be absolutely sure to purchase the AC adaptor / AC plug adaptor
designed especially for this unit.
AC adaptor: AA-R4513 (for the U.S.A. and Canada)
AA-R4516 (for multi voltage area)
AC plug adaptor: QAM0060-001 (for multi voltage
area)
For details, check with your dealer.
E
L
E
C
T
R
O
N I
C
I N D
U
S
T
R
IE
S
·
A
S
S O
C I A T
I O
N
·
EST. 1924
INFORMATION (For Canada)
This digital apparatus does not exceed the Class B limits for radio
noise emissions from digital apparatus as set out in the
interference-causing
equipment
standard
entitled
"Digital
Apparatus", ICES-003 of the Department of Communications.
VARNING: Synlig Och
osynlig laserstrålning när
den öppnas och spärren är
urkopplad. Betrakta ej
strålen.
(s)
CAUTION: Visible and invisible
laser radiation when open and
interlock failed or defeated.
AVOID DIRECT EXPOSURE TO
BEAM.
(e)
ADVARSEL: Synlig og usynlig
laserstråling når maskinen er
åben eller interlocken fejle.
Undgå direkte eksponering
til stråling.
(d)
VARO: Avattaessa ja
Suojalukitus ohitettunatai
viallisena olet alttiina näkyvälle
ja näkymättömälle lasersäteilylle.
Vältä säteen kohdistumista
suoraan itseesi.
(f)
IMPORTANT FOR LASER PRODUCTS
1. CLASS 1 LASER PRODUCT
2. CAUTION: Do not open the top cover. There are
no user serviceable parts inside the unit; leave all
servicing to qualified service personnel.
3. CAUTION: Visible and invisible laser radiation
when open and interlock failed or defeated. Avoid
direct exposure to beam.
4. REPRODUCTION OF LABEL: CAUTION LABEL,
PLACED OUTSIDE THE UNIT.


background image
4
3
2
XL-PG300A/XL-PG300B/XL-PG300Y / LVT1178-001A / J,C,UJ
XL-PG300A/XL-PG300B/XL-PG300Y / LVT1178-001A / J,C,UJ
XL-PG300A/XL-PG300B/XL-PG300Y / LVT1178-001A / J,C,UJ
p3
p4
p2
4
VOLUME
6
VOLUME
1
5
3
RL
OFF
ON
HOLD
0102 3
5
2
Button
Operation
To pause
To stop
To turn off the
unit
Fast forward/
reverse
Display/reference
0700 8
1
1044 8
4
Skip function
During play,
Search function
Keep depressed during play.
· Play stops automatically
when all the tracks have
been played.
For your reference:
"dISC"
This indication appears if
3/8 is pressed when no disc is loaded
or if the disc is not properly seated.
"­ ­"
Preparation period before playing the track
Flashes for several seconds after pressing
3/8 to play.
"OPEn"
This indication appears when the lid is open.
Removing discs
Turn off the unit and, after the disc has stopped rotating, remove
the disc as shown below:
Auto power off
If the unit is left in stop mode for 30 seconds, the unit turns
itself off automatically to prevent the batteries from running
down.
Disc rotation noise
The portable CD player uses a power-saving operation method
so that disc rotation noise will intermittently be emitted. But, it
is not a failure.
· To skip back to the previous track, quickly press
4
twice.
· During Program play, the button is used to fast for-
ward or back through the programmed sequence of
tracks.
· During Random play, the skip button cannot be used
to skip back to tracks that were played previously in
the random sequence.
During play,
During play,
Reverse
Basic Play
Total number of tracks
Total playing time.
Label side
Elapsed playing time of
each track
No indication
Intro play
You can successively play the first 10 seconds of every track.
1 While stopped,
INTRO
MODE
2
To cancel
Press MODE repeatedly until "INTRO" goes out.
Notes:
· You can also select Intro play during playback.
In this case, Intro play will start from the next track after the
current track has finished.
· You can also select Intro play during Program play mode.
Random play
During playback,
MODE
RANDOM
After playing all tracks, the unit stops.
To cancel
Press MODE until "RANDOM" goes out, or press
7 to stop the
disc.
Notes:
· You can also select Random play in stop mode.
· During Program play, you can not select Random play.
Program play
You can program up to 32 tracks in any desired order including
the same tracks.
1 While stopped,
PROG
0001
PROGRAM
2 Select the desired track.
PROG
0301
3
PROG
0002
PROGRAM
The track is registered.
4 Repeat steps 2 and 3.
When you program exceeding 32 tracks, the program se-
quence number returns to "01" and will overwrite the previ-
ous setting.
5
· To confirm the program
While stopped, press PROGRAM repeatedly. At this time, you
can change the program, if required.
· To delete the entire program
Turn off the unit.
Program sequence
number
Track number to be programmed
00: Not programmed yet.
e.g. Track number 3
Repeat play
You can repeat one track or all tracks.
During playback,
I
MODE
ALL
To cancel
Press MODE repeatedly until the repeat indicator goes out.
Notes:
· You can also select Repeat play during Program play.
· You can also select Repeat play while stopped.
Hyper-Bass Sound effect
You can enjoy powerful bass sound.
OFF
2
1
HBS
HBS
Anti-Shock Protection EX
This function achieves excellent performance against sound inter-
ruption caused by vibrations. You will be able to enjoy listening
to music during (not vigorous) jogging.
By utilizing the high-performance servo circuit, audio data will be
stored in the memory ahead of time (up to 45 seconds worth).
Normally, this function is in effect.
ANTI
SHOCK
As the audio data is gradually stored, the indicator changes as follows:
To cancel
A.S.P
The "ANTI SHOCK" indicator goes out.
To activate again
Press the ASP button.
Notes:
· During this operation, the disc rotates at a higher rate than usual
in order to collect extra audio data. This may cause the batteries
to run out faster and could result in a slight increase in disc rota-
tion noise.
· This function can be switched ON and OFF during playback.
However, this may cause a slight interruption in the sound be-
cause the disc's rotational speed changes.
[Fully stored]
ANTI SHOCK
indicator
(Repeatedly)
Next program sequence number
(Repeatedly)
Other Play Methods
(Repeatedly)
Power Supply Preparations
The illustration of the grip band is omitted.
Using dry-cell batteries
(not supplied)
Caution:
Do not forcibly open the battery lid too wide.
Battery indicator
This indicator appears when the batteries are almost out of power.
Power will be cut off a short while later.
Note:
Turning off the Anti-Shock Protection EX will save the battery power
more or less. For details, see "Anti-shock Protection EX" on page 4.
Battery indicator
AC adaptor
Using the AC adaptor (not supplied)
Notes:
· Even if the unit is turned off, small power is consumed as long
as the AC adaptor is connected to the AC power outlet.
· When you want to purchase the AC adaptor, see page 5.
AC power outlet
· When the unit is in Hold mode, "HoLd" and "
" lights as
follows.
Power on : "
" stays lit.
Power off : "HoLd" and "
" lights up for a few seconds
when
6 is pressed.
Note:
If the HOLD switch is set to the ON position, you cannot turn on
the unit.
This function causes the unit to ignore, accidental button presses.
Hold mode prevents the following:
· Powering on the unit accidentally (which can cause the batter-
ies to go dead).
· Play being cut off unexpectedly.
To use the Hold mode
OFF
ON
HOLD
· To prevent the unit from powering on accidentally, set the
HOLD switch to the ON position while the unit is turned off.
· To prevent the unit from unexpected operation during play,
set the HOLD switch to the ON position after you starts play-
ing the disc.
Preventing Accidental Operation (Hold mode)
The illustration of the grip band is omitted.
Follow the steps in the numerical order.
Two "AA" (LR6) alkaline batteries.
AC adaptor (for multi voltage area only)
(not supplied)
Before use
Make sure the present voltage of your AC adaptor fits to your lo-
cal voltage before plugging it into the AC power outlet. If it
doesn't, shift the AC line-voltage selector with a screwdriver so
that it corresponds to your local voltage.
VOLTAGE
ADJUSTOR
AC 110V
~127V
AC 220V
~240V
If the power plug will not fit your socket, use the AC plug adaptor.
How to use the AC plug adaptor (not
supplied)
Note:
When you want to purchase the AC adaptor and the AC plug
adaptor, see page 5.
Track number in play
Firmly connect
Forward
While stopped,
Press again to restart play.