Precautions for installation
To prevent deformation or discoloration of the cabinet, do not install the unit
where it is exposed to direct sunlight or high humidity, and avoid installation
near air conditioning outlets.
Speaker vibrations may cause howling. Place the unit as far away from the player as
possible.
Take the occurrence of earthquakes or other physical shocks into consideration
when selecting the installation place, and secure the unit thoroughly.
Tuner reception may become noisy or hissing if this unit is installed nearby the
tuner. In this case, leave a more distance between the tuner and this unit or
use an outdoor antenna for better tuner reception without interference from this
unit.
The unit is magnetically shielded to avoid color distortions on TVs. However,
if not installed properly, it may cause color distortions. So, pay attention to the
following when installing the unit.
When placing this unit near a TV set, turn off the TV's main power switch or
unplug it before installing this unit.
Then wait at least 30 minutes before turning on the TV's main power switch
again.
Some TVs may still be affected even though you have followed the above. If this
happens, move this unit away from the TV.
When the TV screen shakes, move this unit away from the TV to find a position
where the screen doesn't shake and then set the unit there.
o
·
·
·
·
·
·
PHASE
REVERSE
(LOW LEVEL)
RIGHT
MONO
LEFT
RIGHT
LEFT
RIGHT
LEFT
NORMAL
AUTO ON/
STANDBY
CANCEL
ON
ON
OFF
VOLUME
OUTPUT
POWER
200Hz
50Hz
CUT OFF
FREQUENCY
MAX
MIN
INPUT 2
(HIGH LEVEL)
INPUT 1
(LOW LEVEL)
RIGHT
LEFT
FRONT SPEAKERS
2
1
RIGHT
LEFT
RIGHT
LEFT
INPUT 2
(HIGH LEVEL)
SX-DW55
SX-DW55
PHASE
REVERSE
(LOW LEVEL)
RIGHT
MONO
LEFT
RIGHT
LEFT
RIGHT
LEFT
NORMAL
AUTO ON/
STANDBY
CANCEL
ON
ON
OFF
VOLUME
OUTPUT
POWER
200Hz
50Hz
CUT OFF
FREQUENCY
MAX
MIN
INPUT 2
(HIGH LEVEL)
INPUT 1
(LOW LEVEL)
RIGHT
LINE OUT
L
R
(LOW LEVEL)
RIGHT
MONO
LEFT
OUTPUT
INPUT 1
(LOW LEVEL)
SX-DW55
SUBWOOFER
OUT
PHASE
REVERSE
(LOW LEVEL)
RIGHT
MONO
LEFT
RIGHT
LEFT
RIGHT
LEFT
NORMAL
AUTO ON/
STANDBY
CANCEL
ON
ON
OFF
VOLUME
OUTPUT
POWER
200Hz
50Hz
CUT OFF
FREQUENCY
MAX
MIN
INPUT 2
(HIGH LEVEL)
INPUT 1
(LOW LEVEL)
(LOW LEVEL)
RIGHT
MONO
LEFT
OUTPUT
INPUT 1
(LOW LEVEL)
Main (Front) Speakers
(not supplied)
Monaural audio cord
(supplied)
To an AC outlet
Your Amplifier
Front:
No obstructions and open spacing.
Sides/ Top/ Back: No obstructions should be placed in the areas shown by the
dimensions below.
Bottom:
Place on the level surface. Maintain an adequate air path for
ventilation by placing on a stand with a height of 10 cm or
more.
15 cm
15 cm
20 cm
10 cm
20 cm
20 cm
MAINS (AC) LINE INSTRUCTION
(not applicable for Europe, U.S.A., Canada, Australia, and U.K.)
IMPORTANT for mains (AC) line
BEFORE PLUGGING IN, do check that your mains (AC) line voltage corresponds
with the position of the voltage selector switch provided on the outside of this
equipment and, if different, reset the voltage selector switch, to prevent from a
damage or risk of fire/electric shock.
Setting the VOLTAGE SELECTOR switch
To avoid damaging the powered subwoofer, set the VOLTAGE SELECTOR switch
to the voltage of your area.
1.
2.
3.
o
Warnings, Cautions and Others
Caution!
To avoid personal injury or accidentally dropping the unit, have
two persons unpack, carry, and install the unit.
To reduce the risk of electrical shocks, fire, etc.:
Do not remove screws, covers or cabinet.
Do not expose this appliance to rain or moisture.
Caution--POWER switch
This apparatus is provided with POWER switch to minimize power consumption
for safe use. Therefore,
Before doing initial settings, complete all the connections required, connect
the mains plug into the wall outlet, then set the POWER switch to ON [ B ].
The power lamp lights in green or red.
Press the AUTO ON / STANDBY switch to the ON [ A ] position.
If no sound comes in for a few minutes, the unit enters standby mode.
The power lamp lights in red.
If the unit detects incoming signals, the unit starts operating. The power
lamp lights in green.
Press out the AUTO ON / STANDBY switch to set it to the [ B ] CANCEL
position. The power lamp lights in green.
When not in use, set the POWER switch to OFF [ A ].
This disconnects the main line.
Cautions
Do not block the ventilation openings or holes. (If the ventilation openings or
holes are blocked by a newspaper or cloth, etc., the heat may not be able to get
out.)
Do not place any naked flame sources, such as lighted candles, on the
apparatus.
When discarding batteries, environmental problems must be considered and
local rules or laws governing the disposal of these batteries must be followed
strictly.
Do not expose this apparatus to rain, moisture, dripping or splashing and that
no objects filled with liquids, such as vases, shall be placed on the apparatus.
Caution--Proper Ventilation
To avoid risk of electric shock and fire, and to prevent damage, locate the
apparatus as follows:
o
1.
2.
o
1.
2.
·
·
3.
4.
o
·
·
·
·
o
SX-DW55
POWERED SUBWOOFER
INSTRUCTIONS
0705NSMSANHCE
EN
Connections (Make all connections before plugging in this unit.)
Checking Your Amplifier
Before connecting this unit to your amplifier (or receiver), check what types of
connecting terminals your amplifier has.
Follow the instructions below to find a proper connection method for your
equipment.
Illustrations of jacks and terminals in this manual may be different from the
ones actually used for your amplifier. The illustrations are of the most used
type.
·
Connecting Method A
o
LVT1361-007A
[US]
© 2005 Victor Company of Japan, Limited
Next check whether your amplifier has line output jacks.
They are usually named and printed as "LINE OUT" or "LINE OUTPUT."
Memo
You can connect two or more subwoofer as desired with this
terminal.
Operations
FRONT
Power lamp
REAR
Changing the Phase--PHASE D
You can change the sound phase to match your preference.
Select either "NORMAL" or "REVERSE" to obtain a better bass sound.
Press in or out the PHASE button to select either the NORMAL position or
the REVERSE position.
PHASE
REVERSE
NORMAL
NORMAL : Normally select this.
REVERSE: Select this when you feel the bass sound is better with this mode
rather than with "NORMAL."
Operating the Unit Automatically According to the Incoming Signals
--AUTO ON/STANDBY E
By using this function, this unit automatically enters standby mode even though the
POWER switch is turned ON [ B ].
Press the AUTO ON/STANDBY button to the A ON position.
If no sound comes in for about 10 minutes, the unit automatically enters
standby mode. The power lamp lights in red. Then if the unit detects incoming
signals, this unit starts operating automatically (the power lamp now lights in
green).
If Auto On/Standby does not work correctly (see "Memo" below), press out the
AUTO ON/STANDBY button to set it to the B CANCEL position. Auto On/Standby
is canceled.
·
·
·
Additional Information
Speaker layout
To obtain the best possible sound from your unit:
Place a subwoofer wherever you like since bass sound is nondirectional.
Normally place it in front of you.
Place all the main speakers at the same distance from the listening position.
Be sure to place the powered subwoofer to the TV's right. If you place the
powered subwoofer to the TV's left, keep sufficient distance between them to
prevent the TV from appearing mottled.
Center speaker
Front left
speaker
Powered
subwoofer
Surround left
speaker
Front right
speaker
Surround right
speaker
Precautions for Daily Use
To maintain the appearance of the unit
Wipe with a dry, soft cloth if the cabinet or control panel should become dirty.
If very dirty, apply a small amount of water or neutral detergent to the cloth and
wipe clean. Then wipe with a dry cloth.
To improve the sound field
If the speakers are facing a solid wall or glass door, etc., it is recommended to
furnish the wall with materials that absorb sounds, for example by hanging up
thick curtains, to prevent reflections and standing waves.
o
·
·
Troubleshooting
Use this chart to help you solve daily operational problems. If there is any problem you cannot solve, contact your dealer.
Specifications
Symptom
Power does not come on.
Auto On/Standby does not function correctly.
No sound is heard.
Sounds fluctuate (suddenly become loud or soft).
Suddenly no sound comes out.
the power lamp lights in red.
Suddenly no sound comes out.
the power lamp still lights in green.
Possible Cause
Is the unit plugged in?
Signals are too weak or volume level is too low.
Is the VOLUME knob turned to the MIN position?
Connections are incorrect, or loose.
Audio signals through the amplifier are extremely
weak.
The built-in protective circuit is working.
The VOLUME knob on the rear is set to a very high
level.
The volume of the playback source is too high.
Action
Plug the AC power cord firmly into the AC outlet.
This is not a malfunction. If this happens, cancel
Auto On/Standby.
Turn the VOLUME knob until a suitable volume is
found.
Check the connections. If incorrect, redo the
corrections.
Increase the volume level on the amplifier.
Lower the volume level on the amplifier so that the
symptom will not occur.
Turn down the volume, then turn off and on this
unit.
Turn down the volume of the playback source,
turn off and on the source, then adjust the volume
properly on the source.
Turning On the Power--POWER A
Press the ON [ B ] portion of the POWER button.
The main power turns on and the power lamp in the front panel lights in green.
The power lamp lights in red when the Auto On/ Standby places the unit into
standby mode.
To completely cut off the power to this unit
Press the OFF [ A ] portion of the POWER button.
This will disconnect the mains lead.
Adjusting the Volume--VOLUME B
Adjust the volume output level through this unit while comparing with the sounds
coming out of the main (front) speakers.
Once you have adjusted the volume output level of this unit, you do not need to
adjust it each time you use this unit.
Adjusting the volume level on the connected amplifier will also adjust the
volume level through this unit.
Turn the VOLUME knob to the MIN position.
Turn on the connected amplifier and start playing a source.
Playback sounds come out of the main (front) speakers and this unit.
Adjust the VOLUME knob to obtain a well-balanced sound level with that
of the main (front) speakers.
Caution
If the volume is set at a high level before starting play, the sudden blast of sound
energy can permanently damage your hearing and/or ruin your speakers.
Adjusting the Crossover Frequency
--CUT OFF FREQUENCY C
You can adjust the crossover frequency to determine the bass sound level this unit
handles.
Once it is set, only the sounds below the frequency come out of the built-in
speaker.
Turn the CUT OFF FREQUENCY knob to obtain the best matching crossover
frequency with your main speakers.
Adjust the frequency (50 Hz to 200 Hz) while listening to playback sound coming
out of both the main speakers and this unit.
If your main speakers can reproduce the bass sound well, adjust the frequency
at a lower level.
If you feel bass sounds are not sufficient, adjust the frequency at a higher level.
·
·
1.
2.
3.
·
·
·
ON
OFF
POWER
Type
: Powered Subwoofer
Bass-reflex type, (magnetically shielded type)
Speaker unit
: 25.0 cm cone (× 1)
Frequency range
: 25 Hz to 200 Hz
Input impedance
: 50 kK (LOW LEVEL)
470 K (HIGH LEVEL)
Input terminals
: INPUT 1 (LOW LEVEL)
INPUT 2 (HIGH LEVEL)
Power requirements
: AC 110 V/ 127 V/ 220 V - 240 V H adjustable with the voltage selector,
50/ 60 Hz
Output power of built-in amp : 300 W (50 Hz, 4 K, 10 % THD)
Power consumption
: 75 W
Dimensions
: (W/H/D) 254 × 481 × 430.5 mm
Mass
: 18 k
g
Accessories
: Monaural audio cord (× 1)
AC plug adaptor (× 1)
If the item mentioned above is missing,
contact your dealer immediately.
Design and specifications subject to change without notice.
SUBWOOFER
OUT
LINE OUT
L
R
RIGHT
LEFT
FRONT SPEAKERS
2
1
If you cannot
find any
If you cannot
find any
Thank you for purchasing a JVC speaker.
Before you begin using it, please read the instructions carefully to be sure you get
the best possible performance. If you have any questions, consult your JVC dealer.
CAUTION
DO NOT plug the power cord of the powered subwoofer before
setting the VOLTAGE SELECTOR switch to the correct voltage.
Main (Front) Speakers
(not supplied)
Stereo audio cord
(not supplied)
To an AC outlet
Your Amplifier
Speaker cords
(not supplied)
Your Amplifier
Left speaker
Main (Front) Speakers
(not supplied)
Right speaker
To an AC outlet
Speaker cords
(not supplied)
Preparation:
Purchase speaker cords at an audio shop
or electric shop.
VOLUME
MAX
MIN
VOLUME
MAX
MIN
200Hz
50Hz
CUT OFF
FREQUENCY
(LOW LEVEL)
OUTPUT
First check whether your amplifier has a subwoofer output jack.
It is usually named and printed as the "SUBWOOFER OUT" or "SUBWOOFER."
Preparation:
Use the supplied monaural audio cord.
If you find it on your amplifier, follow
Connecting Method A.
If your amplifier has only a monaural line output (MONO) jack, connect it to the
MONO jack of the INPUT 1 (LOW LEVEL) terminal.
Preparation:
Purchase a stereo audio cord at an audio
shop or electric shop.
If you find them on your amplifier, follow
Connecting Method B.
Connecting Method B
o
Connecting Method C
o
Follow
Connecting Method C.
This connection can be used for two amplifiers, by connecting the front speaker
terminals of the amplifier (usually named and printed as "FRONT SPEAKERS" or
"MAIN SPEAKERS").
AUTO ON/
STANDBY
CANCEL
ON
AUTO ON/
STANDBY
CANCEL
ON
Memo
When the volume level of the amplifier is so low or the incoming signals are
so weak that this unit cannot detect sounds, Auto On/Standby may not work
correctly.
This unit may enter standby mode even though signals are coming in.
This unit may not start operating after entering standby mode, even though
signals start coming in.
·
·
Front
Side View
Front View
CAUTION
Before connecting this unit to the amplifier (or receiver), observe the following carefully.
Turn off the amplifier.
DO NOT use the INPUT 1 (LOW LEVEL) and INPUT 2 (HIGH LEVEL) terminals on the rear of this unit at the same time; otherwise, noise will be heard and may
damage the unit.
DO NOT connect this unit to the REC OUT jacks of your amplifier.
·
·
·
PHASE
REVERSE
(LOW LEVEL)
RIGHT
MONO
LEFT
RIGHT
LEFT
RIGHT
LEFT
NORMAL
AUTO ON/
STANDBY
CANCEL
ON
ON
OFF
VOLUME
OUTPUT
POWER
200Hz
50Hz
CUT OFF
FREQUENCY
MAX
MIN
INPUT 2
(HIGH LEVEL)
INPUT 1
(LOW LEVEL)
PHASE
VOLUME
CUT OFF
FREQUENCY
B
C
D
AUTO ON/
STANDBY
POWER
A
E
21 kg
SX-DW55[US]_En_A2.indd 2
7/13/2005 1:47:07 PM
30
o
·
·
·
·
·
·
PHASE
REVERSE
(LOW LEVEL)
RIGHT
MONO
LEFT
RIGHT
LEFT
RIGHT
LEFT
NORMAL
AUTO ON/
STANDBY
CANCEL
ON
ON
OFF
VOLUME
OUTPUT
POWER
200Hz
50Hz
CUT OFF
FREQUENCY
MAX
MIN
INPUT 2
(HIGH LEVEL)
INPUT 1
(LOW LEVEL)
RIGHT
LEFT
FRONT SPEAKERS
2
1
RIGHT
LEFT
RIGHT
LEFT
INPUT 2
(HIGH LEVEL)
SX-DW55
SX-DW55
PHASE
REVERSE
(LOW LEVEL)
RIGHT
MONO
LEFT
RIGHT
LEFT
RIGHT
LEFT
NORMAL
AUTO ON/
STANDBY
CANCEL
ON
ON
OFF
VOLUME
OUTPUT
POWER
200Hz
50Hz
CUT OFF
FREQUENCY
MAX
MIN
INPUT 2
(HIGH LEVEL)
INPUT 1
(LOW LEVEL)
RIGHT
LINE OUT
L
R
(LOW LEVEL)
RIGHT
MONO
LEFT
OUTPUT
INPUT 1
(LOW LEVEL)
SX-DW55
SUBWOOFER
OUT
PHASE
REVERSE
(LOW LEVEL)
RIGHT
MONO
LEFT
RIGHT
LEFT
RIGHT
LEFT
NORMAL
AUTO ON/
STANDBY
CANCEL
ON
ON
OFF
VOLUME
OUTPUT
POWER
200Hz
50Hz
CUT OFF
FREQUENCY
MAX
MIN
INPUT 2
(HIGH LEVEL)
INPUT 1
(LOW LEVEL)
(LOW LEVEL)
RIGHT
MONO
LEFT
OUTPUT
INPUT 1
(LOW LEVEL)
--
//
10 cm
15 cm
15 cm
20 cm
10 cm
20 cm
20 cm
AC
AC
,AC
/
o
1.
2.
3.
o
!
:
--POWER()
POWER()
POWER() ON [ B ]()
AUTO ON / STANDBY [ A ] ON
AUTO ON / STANDBY [ B ] CANCEL
POWER() OFF [ A ]()
(
)
o
1.
2.
o
1.
2.
·
·
3.
4.
o
·
·
·
·
SX-DW55
0705NSMSANHCE
CS
·
A
o
LVT1361-007A
[US]
© 2005 Victor Company of Japan, Limited
"LINE OUT""LINE OUTPUT"
--PHASE D
"NORMAL""REVERSE"
PHASE NORMAL REVERSE
PHASE
REVERSE
NORMAL
NORMAL
:
REVERSE
:
"NORMAL"
--
AUTO ON/STANDBY E
POWER [ B ]
AUTO ON/STANDBY A ON
10
/"" AUTO ON/STANDBY
B CANCEL /
·
·
·
o
·
·
/
VOLUME MIN
VOLUME ()
/
VOLUME
--
POWER A
POWER ON [ B ]
Auto On/Standby
POWER OFF [ A ]
--
VOLUME B
VOLUME MIN
VOLUME
/
--
CUT OFF FREQUENCY C
CUT OFF FREQUENCY
50 Hz 200 Hz
,
·
·
1.
2.
3.
·
·
·
ON
OFF
POWER
:
: 25.0 cm (× 1)
: 25 Hz 200 Hz
: 50 kK (LOW LEVEL)
470 K (HIGH LEVEL)
: INPUT 1 (LOW LEVEL)
INPUT 2 (HIGH LEVEL)
: 110 V/ 127 V/220 V - 240 VH
50/60 Hz
: 300 (50 Hz4 K10 % THD)
: 75
W/H/D
: 254 x 481 x 430.5
: 18
: x 1
x 1
,
SUBWOOFER
OUT
LINE OUT
L
R
RIGHT
LEFT
FRONT SPEAKERS
2
1
JVC
JVC
VOLTAGE SELECTOR
VOLUME
MAX
MIN
VOLUME
MAX
MIN
200Hz
50Hz
CUT OFF
FREQUENCY
(LOW LEVEL)
OUTPUT
"SUBWOOFER OUT""SUBWOOFER"
A
MONO INPUT 1(LOW
LEVEL) MONO
B
B
o
C
o
C
"FRONT SPEAKERS""MAIN SPEAKERS"
AUTO ON/
STANDBY
CANCEL
ON
AUTO ON/
STANDBY
CANCEL
ON
/
·
·
INPUT 1LOW LEVEL INPUT 2HIGH LEVEL
REC OUT
·
·
·
PHASE
REVERSE
(LOW LEVEL)
RIGHT
MONO
LEFT
RIGHT
LEFT
RIGHT
LEFT
NORMAL
AUTO ON/
STANDBY
CANCEL
ON
ON
OFF
VOLUME
OUTPUT
POWER
200Hz
50Hz
CUT OFF
FREQUENCY
MAX
MIN
INPUT 2
(HIGH LEVEL)
INPUT 1
(LOW LEVEL)
PHASE
VOLUME
CUT OFF
FREQUENCY
B
C
D
AUTO ON/
STANDBY
POWER
A
E
21 kg
VOLTAGE SELECTOR
VOLTAGE SELECTOR
SX-DW55[US]_Cs_A2.indd 2
7/13/2005 1:48:09 PM