For Customer Use:
Enter below the Model No. and Serial
No. which are located either on the rear,
bottom or side of the cabinet. Retain this
information for future reference.
Model No.
Serial No.
LVT1007-001A[J]
RX-8030VBK
RX-7030VBK/RX-7032VSL
AUDIO/VIDEO CONTROL RECEIVER
INSTRUCTIONS
23
1
56
4
89
7/P
0
+10
MENU
ENTER
CONTROL
A/V CONTROL RECEIVER
10/0
(For RX-8030VBK)
(For RX-8030VBK)
COVER_8030&7030[J]f.pm6
03.2.13, 4:39 PM
1
G-1
CAUTION
To reduce the risk of electrical shocks, fire, etc.:
1.
Do not remove screws, covers or cabinet.
2.
Do not expose this appliance to rain or moisture.
ATTENTION
Afin d'éviter tout risque d'électrocution, d'incendie, etc.:
1.
Ne pas enlever les vis ni les panneaux et ne pas ouvrir le
coffret de l'appareil.
2.
Ne pas exposer l'appareil à la pluie ni à l'humidité.
Warnings, Cautions and Others/
Mises en garde, précautions et indications diverses
Caution
STANDBY/ON button!
Disconnect the mains plug to shut the power off completely. The
STANDBY/ON button in any position does not disconnect
the mains line. The power can be remote controlled.
Attention Commutateur
STANDBY/ON!
Déconnecter la fiche de secteur pour couper complètement le
courant. Le commutateur
STANDBY/ON ne coupe jamais
complètement la ligne de secteur, quelle que soit sa position. Le
courant peut être télécommandé.
Note to CATV system installer:
This reminder is provided to call the CATV system installer's
attention to Section 820-40 of the NEC which provides guidelines for
proper grounding and, in particular, specifies that the cable ground
shall be connected to the grounding system of the building, as close
to the point of cable entry as practical.
For Canada/pour Le Canada
THIS DIGITAL APPARATUS DOES NOT EXCEED THE CLASS B
LIMITS FOR RADIO NOISE EMISSIONS FROM DIGITAL APPA-
RATUS AS SET OUT IN THE INTERFERENCE-CAUSING
EQUIPMENT STANDARD ENTITLED "DIGITAL APPARATUS,"
ICES-003 OF THE DEPARTMENT OF COMMUNICATIONS.
CET APPAREIL NUMERIQUE RESPECTE LES LIMITES DE
BRUITS RADIOELECTRIQUES APPLICABLES AUX APPAREILS
NUMERIQUES DE CLASSE B PRESCRITES DANS LA NORME
SUR LE MATERIEL BROUILLEUR; "APPAREILS NUMERIQUES",
NMB-003 EDICTEE PAR LE MINISTRE DES COMMUNICATIONS.
CAUTION:
TO REDUCE THE RISK OF ELECTRIC SHOCK.
DO NOT REMOVE COVER (OR BACK)
NO USER SERVICEABLE PARTS INSIDE.
REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.
RISK OF ELECTRIC SHOCK
DO NOT OPEN
The lightning flash with arrowhead symbol,
within an equilateral triangle is intended to
alert the user to the presence of uninsulated
"dangerous voltage" within the product's
enclosure
that
may
be
of
sufficient
magnitude to constitute a risk of electric
shock to persons.
The exclamation point within an equilateral
triangle is intended to alert the user to the
presence
of
important
operating
and
maintenance (servicing) instructions in the
literature accompanying the appliance.
CAUTION
WARNING: TO REDUCE THE RISK OF FIRE
OR ELECTRIC SHOCK, DO NOT EXPOSE
THIS APPLIANCE TO RAIN OR MOISTURE.
For U.S.A
This equipment has been tested and found to comply with the limits
for a Class B digital device, pursuant to part 15 of the FCC Rules.
These limits are designed to provide reasonable protection against
harmful interference in a residential installation.
This equipment generates, uses and can radiate radio frequency
energy and, if not installed and used in accordance with the
instructions,
may
cause
harmful
interference
to
radio
communications. However, there is no guarantee that interference
will not occur in a particular installation. If this equipment does cause
harmful interference to radio or television reception, which can be
determined by turning the equipment off and on, the user is
encouraged to try to correct the interference by one or more of the
following measures:
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that
to which the receiver is connected.
Consult the dealer or an experienced radio/TV technician for help.
Changes
or
modifications
not
expressly
approved
by
the
manufacturer for compliance could void the user s authority to
opratethe equipment.
CAUTION: TO PREVENT ELECTRIC SHOCK, MATCH WIDE
BLADE OF PLUG TO WIDE SLOT, FULLY INSERT
ATTENTION: POUR EVITER LES CHOCS ELECTRIQUES,
INTRODUIRE LA LAME LA PLUS LARGE DE LA FICHE DANS LA
BORNE CORRESPONDANTE DE LA PRISE ET POUSSER
JUSQUAU FOND
Safety_8030&7030[J]f.pm6
03.2.13, 4:39 PM
1
1
Table of Contents
Basic Settings ........................................... 25
Setting the Speakers Configuration .......................................... 25
Basic Setting Items ................................................................... 26
Basic Procedure ........................................................................ 27
Setting the Speakers ........................................................... 27
Setting the Speaker Distance ............................................. 28
Setting the Bass Sounds ..................................................... 28
Selecting main or sub channel--DUAL MONO ............... 29
Setting the Digital Input Terminals .................................... 29
Setting the Component Video Input ................................... 30
Memorizing the Volume Level for Each Source ................ 30
Adjusting Sound ........................................ 31
Basic Setting Items ................................................................... 31
Basic Procedure ........................................................................ 31
Adjusting the Equalization Patterns ................................... 32
Adjusting the Speaker Output Levels ................................ 32
Adjusting the Sound Parameters for the
Surround and DSP modes ............................................ 33
Using the Surround Modes .......................... 34
Reproducing Theater Ambience ................................................ 34
Introducing the Surround Modes ............................................. 34
Surround Modes Applicable to the Various Software .............. 36
Activating the Surround Modes ............................................... 37
7 Activating the EX/ES setting ................................................ 37
7 Activating the Surroung modes ............................................ 37
Using the DSP Modes ................................ 38
Reproducing the Sound Field ................................................... 38
Introducing the DSP Modes ..................................................... 38
Activating the DSP Modes ....................................................... 39
Using the DVD MULTI Playback Mode .......... 40
Activating the DVD MULTI Playback Mode .......................... 40
COMPU LINK Remote Control System ......... 41
AV COMPU LINK Remote Control System .... 42
Operating JVC's Audio/Video Components ... 44
Operating Audio Components .................................................. 44
Operating Video Components .................................................. 46
Operating Other Manufacturers' Video
Equipment ............................................ 47
Troubleshooting ......................................... 50
Specifications ............................................ 51
Introduction ................................................ 2
Features ...................................................................................... 2
Precautions ................................................................................. 2
Parts Identification ...................................... 3
Remote Control .......................................................................... 3
Front Panel ................................................................................. 4
Rear Panel .................................................................................. 6
Getting Started ........................................... 8
Before Installation ...................................................................... 8
Checking the Supplied Accessories ........................................... 8
Putting Batteries in the Remote Control .................................... 8
Connecting the FM and AM Antennas ....................................... 8
Connecting the Speakers ............................................................ 9
Connecting Audio/Video Components ..................................... 11
7 Analog Connections ............................................................. 11
7 Digital Connections .............................................................. 16
Connecting the Power Cord ..................................................... 16
Basic Operations ....................................... 17
Daily Operational Procedure .................................................... 17
Turning On the Power .............................................................. 17
Selecting the Source to Play ..................................................... 17
Adjusting the Volume ............................................................... 18
Selecting the Front Speakers .................................................... 19
Activating and Adjusting the Subwoofer Sound ...................... 19
Selecting the Analog or Digital Input Mode ............................ 19
Setting the Dynamic Range ...................................................... 20
Attenuating the Input Signal .................................................... 20
Turning Analog Direct On and Off .......................................... 21
Making Sounds Natural ............................................................ 21
Changing the Source Name ...................................................... 21
Reinforcing the Bass ................................................................ 22
Muting the Sound ..................................................................... 22
Changing the Display Brightness ............................................. 22
Using the Sleep Timer .............................................................. 22
Receiving Radio Broadcasts ........................ 23
Tuning in to Stations Manually ................................................ 23
Using Preset Tuning ................................................................. 23
Selecting the FM Reception Mode ........................................... 24
This mark indicates that ONLY the remote control
CAN be used for the operation explained.
This mark indicates that the remote control
CANNOT be used for the operation explained.
Use the buttons on the front panel.
Features with this mark are provided only for
RX-8030VBK.
Features with this mark are provided only for
RX-7030VBK/RX-7032VSL.
RX-8030V
ONLY
RX-7030V
RX-7032V
ONLY
Remote
NOT
01-16_8030&7030[J]10.pm6
03.2.13, 2:44 PM
1
2
Introduction
We would like to thank you for purchasing one of our JVC products.
Before operating this unit, read this manual carefully and thoroughly to obtain the best possible performance
from your unit, and retain this manual for future reference.
Features
CC (Compensative Compression) converter
--ONLY for RX-8030VBK
CC Converter eliminates jitter and ripples, achieving a drastic
reduction in digital distortion by processing the digital music data
in 24 bitquantization and by expanding the sampling frequency
to 128 kHz (for fs 32 kHz signals)/176.4 kHz (for fs 44.1 kHz
signals)/192 kHz (for fs 48 kHz signals). By using the CC
Converter, you can obtain a natural sound field from any source.
(See page 21 for details.)
K2 technology--ONLY for RX-8030VBK
K2 technology has been designed to enable natural audio
reproduction, achieving a drastic reduction in digital distortion
and creating original sound ambience with high precision.
Compatible with various audio formats including
DTS 96/24
RX-8030VBK and RX-7030VBK/RX-7032VSL allow you to
enjoy a newly introduced audio format such as Dolby Digital EX,
Dolby Pro Logic II, DTS-ES, DTS Neo:6, and DTS 96/24.
· This unit is also compatible with Dual Mono signals recorded in
Dolby Digital and DTS discs.
DAP (Digital Acoustic Processor)
Sound field simulation technology allows precise ambience
recreation of existing theaters and halls. Thanks to the high-
performance DSP (Digital Signal Processor) and high-capacity
memory, you can enjoy multi-channel surround sound by playing
2-channel or multi-channel software according to the speaker
setting.
Multi-channel headphone virtual surround
sound--3D HEADPHONE Mode
The built-in headphone virtual surround system is compatible with
Multi-channel software like Dolby Digital, DTS Surround, etc.
Thanks to the new signal processing algorithms used by the high-
performance DSP, you can enjoy a natural surround sound through
the headphones.
COMPU LINK/AV COMPU LINK remote control
systems
These COMPU LINK remote control systems allow you to
operate other JVC's audio/video components from this receiver.
Precautions
Power sources
· When unplugging the receiver from the wall outlet, always pull
the plug, not the AC power cord.
· Do not handle the AC power cord with wet hands.
· If you are not going to operate the receiver for an extended period
of time, unplug the AC power cord from the wall outlet.
Ventilation
High power amplifiers built in this receiver will generate heat inside
the cabinet. For safety, observe the following carefully.
· Make sure there is good ventilation around the receiver. Poor
ventilation could overheat and damage the receiver.
· Do not block the ventilation openings or holes. (If the ventilation
openings or holes are blocked by a newspaper or cloth, etc., the
heat may not be able to get out.)
Others
· Should any metallic object or liquid fall onto the unit, unplug the
unit and consult your dealer before operating any further.
· Do not expose this apparatus to rain, moisture, dripping or
splashing and that no objects filled with liquids, such as vases
shall be placed on the apparatus.
· Do not disassemble the unit since there are no user serviceable
parts inside.
If anything goes wrong, unplug the AC power cord and consult your
JVC dealer.
01-16_8030&7030[J]10.pm6
03.2.13, 2:44 PM
2
3
Parts Identification
1 Only for RX-8030VBK: Display window
· When the remote operation mode changes, it is shown on
this display.
· Signal transmission indicator (A) lights up when
transmitting signals.
2
buttons (17, 46 48)
· For RX-8030VBK:
CATV/DBS
, VCR 1
, TV
, AUDIO
· For RX-7030VBK/RX-7032VSL:
CATV/DBS
, VCR
, TV
, AUDIO
3 Source selection buttons (17, 18, 19, 23, 24, 37, 40)
· For RX-8030VBK:
DVD MULTI, DVD, CD*, FM/AM*, VCR 1, VCR 2,
CDR*, TAPE/MD*, TV/DBS, VIDEO, PHONO*
· For RX-7030VBK/RX-7032VSL:
DVD MULTI, DVD, CD*, FM/AM*, TV/DBS, VCR,
TAPE/CDR*
* When you press one on these source selection buttons on the
remote control, the receiver automatically turns on.
4 · SURROUND button (37)
· DSP button (39)
· SURR (surround)/DSP OFF button (37, 39)
· EX/ES button (37)
5 · For RX-8030VBK: CC CONVERTER button (21)
· For RX-7030VBK/RX-7032VSL: CD DISC button (45)
6 MIDNIGHT MODE button (20)
7 SOUND button (22, 32, 33)
8 CATV/DBS CONTROL button (47)
9 TV/VIDEO button (46, 47)
p · For RX-8030VBK: CONTROL button (44 46)
· For RX-7030VBK/RX-7032VSL:
VCR CONTROL button (46)
q REC PAUSE button (45, 46, 48)
w SLEEP button (22)
e ANALOG/DIGITAL INPUT button (20)
r ANALOG DIRECT button (21)
t · 10 keys for operating the tuner (24)
· 10 keys for adjusting sound (32, 33)
· 10 keys for operating audio/video components (44 48)
y · CH (channel) +/ buttons (46 48)
· *LEVEL +/ buttons (32, 33, 44)
The LEVEL +/ buttons function only after pressing SOUND
then 10 keys which are marked with an asterisk (*) on the
remote control.
u VOLUME +/ buttons (18)
i TV VOL (volume) +/ buttons (46, 47)
o MUTING button (22)
; · TUNING UP/DOWN buttons (23)
· Operating buttons for audio/video components (44 46, 48)
3, 8, 7, 4/REW, FF/¢
a DIMMER button (22)
å Only for RX-7030VBK/RX-7032VSL:
TAPE/CDR CONTROL button (45)
Remote Control
RX-8030VBK
RX-7030VBK/RX-7032VSL
+
-
+
-
+
-
23
1
56
4
89
7/P
0
+10
MENU
ENTER
BASSBOOST
TEST
CENTERSUBWOOFER
DIGITALEQ SURR BACK
CH/
LEVEL TVVOL
/REW
DOWN -- TUNING -- UP
FF/
MUTING
DIMMER
VOLUME
CATV/DBS
CONTROL
TV/VIDEO
REC PAUSE
SLEEP
RETURN
FMMODE
100+
CONTROL
CATV/DBS
VCR 1
TV
AUDIO
DSP
OFF
DVD MULTI
CD
CDR
TAPE/MD
TV/DBS
VIDEO
PHONO
FM/AM
VCR 1
VCR 2
SURROUND
EX/ES
CCCONVERTER
SURR/DSP
ANALOG/DIGITAL
A/V CONTROL RECEIVER
INPUT
MIDNIGHT
MODE
DIRECT
ANALOG
DVD
u
i
1
3
4
9
p
q
w
t
;
a
10/0
y
2
SOUND
8
6
5
7
o
r
e
A
+
-
+
-
+
-
23
1
56
4
89
7/P
0
+10
MENU
ENTER
TEST
CDDISC
CENTERSUBWOOFER
DIGITALEQ SURR BACK
CH/
LEVEL TVVOL
/REW
DOWN -- TUNING -- UP
FF/
MUTING
DIMMER
VOLUME
CATV/DBS
CONTROL
VCR
CONTROL
TAPE/CDR
CONTROL
TV/VIDEO
REC PAUSE
SLEEP
RETURN
FMMODE
100+
CATV/DBS
VCR
TV
AUDIO
DSP
OFF
DVD MULTI
CD
TAPE/CDR ANALOG/DIGITAL
FM/AM
TV/DBS
VCR
SURROUND
EX/ES
SURR/DSP
A/V CONTROL RECEIVER
INPUT
MIDNIGHT
MODE
DIRECT
ANALOG
DVD
u
i
3
4
9
p
q
w
t
;
a
10/0
y
2
SOUND
8
6
5
7
o
r
e
s
BASSBOOST
01-16_8030&7030[J]10.pm6
03.2.13, 2:45 PM
3