INSTRUCTIONS
MANUAL D'INSTRUCTIONS
RM-SRX778J
REMOTE CONTROL
CONTROL
CHANNEL
VOLUME
TV VOL
TUNING
STOP
PAUSE
FF/
/REW
VCR
TV/VIDEO
TAPE
MUTING
REC
PLAY
DOWN
UP
STANDBY
ON
TV/CATV/DBS
VCR
POWER
POWER
DVD
CD
TAPE/MD
TV/DBS
PHONO
FM/AM
VCR
ANALOG/DIGITAL
SURROUND
CNTR
SURROUND
TEST
REAR-L
DISC
MODE
ON/OFF
EFFECT
REAR-R
SOUND
SEA MODE
SUBWOOFER
RETURN
SET
MENU
AUDIO/
TV/VCR
EXIT
TEXT
DISPLAY
FM MODE/MUTING
SLEEP
12
3
45
6
7/P
89
10
0
+10
100+
CATV/DBS
MENU
ENTER
For Customer Use:
Enter below the Model No. and Serial
No. which are located either on the rear,
bottom or side of the cabinet. Retain this
information for future reference.
Model No.
Serial No.
LVT0171-002A
[C]
RX-778VBK
DIGITAL
+
RX-778V AUDIO/VIDEO CONTROL RECEIVER
POWER
STANDBY
SPEAKERS
12
PHONES
DOLBY SURROUND
DSP MODE
BALANCE/SURROUND
ADJUST
SEA MODE
SEA ADJUST
SETTING
MULTI JOG
MASTER VOLUME
SOURCE SELECTOR
DIGITAL INPUT
FM/AM TUNING
TUNER PRESET
TUNER/SEA MEMORY
FM MODE
DVD
TV SOUND/DBS
PHONO
TAPE/MD
VCR
FM
AM
CD
SOUND SELECT
INPUT ATT.
LOUDNESS
ONETOUCHOPERATION
SOURCENAME
COMPULINK
Remote
DIGITAL
DIGITAL SOURCE FORMAT
LINEAR
PCM
DOLBY
DIGITAL
AUDIO/VIDEO CONTROL RECEIVER
RECEPTEUR DE CONTROL AUDIO/VIDEO
RX-778V[C]COVER/1
99.4.12, 11:15 AM
1
Warnings, Cautions and Others/
Mises en garde, précautions et indications diverses
Caution POWER switch!
Disconnect the mains plug to shut the power off completely. The
POWER switch in any position does not disconnect the mains line.
The power can be remote controlled.
Attention Commutateur POWER!
Déconnecter la fiche de secteur pour couper complètement le
courant. Le commutateur POWER ne coupe jamais complètement
la ligne de secteur, quelle que soit sa position. Le courant peut être
télécommandé.
CAUTION
To reduce the risk of electrical shocks, fire, etc.:
1.
Do not remove screws, covers or cabinet.
2.
Do not expose this appliance to rain or moisture.
For Canada/pour le Canada
CAUTION: TO PREVENT ELECTRIC SHOCK, MATCH WIDE
BLADE OF PLUG TO WIDE SLOT, FULLY INSERT
ATTENTION: POUR EVITER LES CHOCS ELECTRIQUES,
INTRODUIRE LA LAME LA PLUS LARGE DE LA FICHE DANS LA
BORNE CORRESPONDANTE DE LA PRISE ET POUSSER
JUSQUAU FOND
ATTENTION
Afin d'éviter tout risque d'électrocution, d'incendie, etc.:
1.
Ne pas enlever les vis ni les panneaux et ne pas ouvrir le coffret de
l'appareil.
2.
Ne pas exposer l'appareil à la pluie ni à l'humidité.
RX-778VBK
Caution: Proper Ventilation
To avoide risk of electric shock and fire and to protect from dam-
age.
Locate the apparatus as follows:
Front:
No obstructions open spacing.
Sides:
No obstructions in 10 cm from the sides.
Top:
No obstructions in 10 cm from the top.
Back:
No obstructions in 15 cm from the back
Bottom:
No obstructions, place on the level surface.
In addition, maintain the best possible air circulation as illustrated.
Attention: Ventilation Correcte
Pour éviter les chocs électriques, l'incendie et tout autre dégât.
Disposer l'appareil en tenant compte des impératifs suivants
Avant:
Rien ne doit gêner le dégagement
Flancs:
Laisser 10 cm de dégagement latéral
Dessus:
Laisser 10 cm de dégagement supérieur
Arrière:
Laisser 15 cm de dégagement arrière
Dessous:
Rien ne doit obstruer par dessous; poser l'appareil
sur une surface plate.
Veiller également à ce que l'air circule le mieux possible comme
illustré.
Wall or obstructions
Mur, ou obstruction
Spacing 15 cm or more
Dégagement de 15 cm ou plus
Front
Avant
Stand height 15 cm or more
Hauteur du socle: 15 cm ou plus
Floor
Plancher
RX-778V[C]SAFETY/f
99.4.27, 11:37 AM
1
1
English
Table of Contents
Using the DSP Modes ................................ 20
Available DSP Modes According to the Speaker Arrangement .. 22
Adjusting the 3D-PHONIC Modes .......................................... 23
Adjusting the DAP Modes ....................................................... 23
Adjusting the Surround Modes ................................................ 24
Activating the DSP Modes ....................................................... 27
Using the On-Screen Menus ........................ 28
Selecting the Source to Play ..................................................... 28
Selecting the Different Source for Picture and Sound ............. 28
Activating the DSP Modes ....................................................... 28
Adjusting the Front Speaker Output Balance ........................... 28
Listening at Low Volume (Loudness) ...................................... 29
Attenuating the Input Signal .................................................... 29
Adjusting the Subwoofer Output Level .................................... 29
Adjusting the DSP Modes ........................................................ 29
Selecting Your Favorite SEA Mode ......................................... 30
Creating Your Own SEA Mode ................................................ 30
Setting the Basic Setting Items ................................................ 31
Operating the Tuner .................................................................. 31
Storing the Preset Stations ....................................................... 32
Assigning Names to Preset Stations ......................................... 32
COMPU LINK Remote Control System ......... 33
TEXT COMPU LINK Remote Control System .. 34
Showing the Disc Information on the TV Screen .................... 35
Searching for a Disc (Only for the CD player) ........................ 36
Entering the Disc Information .................................................. 37
AV COMPU LINK Remote Control System .... 39
Operating JVC's Audio/Video Components ... 41
Operating Other Manufacturers' Video
Equipment ............................................ 43
Troubleshooting ......................................... 45
Specifications ............................................ 46
Parts Identification ...................................... 2
Getting Started ........................................... 3
Before Installation ...................................................................... 3
Checking the Supplied Accessories ........................................... 3
Connecting the FM and AM Antennas ....................................... 3
Connecting the Speakers ............................................................ 4
Connecting Audio/Video Components ....................................... 6
Connecting the Power Cord ....................................................... 8
Putting Batteries in the Remote Control .................................... 8
Basic Operations ......................................... 9
Turning the Power On and Off (Standby) .................................. 9
Selecting the Source to Play ....................................................... 9
Adjusting the Volume ............................................................... 10
Selecting the Front Speakers .................................................... 10
Muting the Sound ..................................................................... 11
Listening at Low Volume (Loudness) ...................................... 11
Attenuating the Input Signal .................................................... 11
Adjusting the Subwoofer Output Level .................................... 11
Basic Settings ........................................... 12
Adjusting the Front Speaker Output Balance ........................... 12
Changing the Source Name ...................................................... 12
Setting the Subwoofer Information .......................................... 12
Digital Input (DIGITAL IN) Terminal Setting ......................... 12
Selecting the Analog or Digital Input Mode ............................ 13
Showing the Text Information on the Display ......................... 13
Setting the Speakers for the DSP Modes ................................. 14
Storing the Basic Settings and Adjustments -- One Touch
Operation ........................................................................... 16
Using the Sleep Timer .............................................................. 16
Recording a Source .................................................................. 16
Receiving Radio Broadcasts ........................ 17
Tuning in Stations Manually .................................................... 17
Using Preset Tuning ................................................................. 17
Selecting the FM Reception Mode ........................................... 18
Assigning Names to Preset Stations ......................................... 18
Using the SEA Modes ................................ 19
Selecting Your Favorite SEA Mode ........................................... 19
Creating Your Own SEA Mode ................................................ 19
EN01-08.RX-778V[C]/1
99.4.23, 9:02 AM
1
2
English
+
RX-778V AUDIO/VIDEO CONTROL RECEIVER
POWER
STANDBY
DIGITAL SOURCE FORMAT
LINEAR
PCM
DOLBY
DIGITAL
SPEAKERS
12
PHONES
DOLBY SURROUND
DSP MODE
BALANCE/SURROUND
ADJUST
SEA MODE
SEA ADJUST
SETTING
MULTI JOG
MASTER VOLUME
SOURCE SELECTOR
INPUT
ANALOG/DIGITAL
FM/AM TUNING
TUNER PRESET
TUNER/SEA MEMORY
FM MODE
DVD
TV SOUND/DBS
PHONO
TAPE/MD
VCR
FM
AM
CD
SOUND SELECT
INPUT ATT.
LOUDNESS
ONETOUCHOPERATION
SOURCENAME
COMPULINK
Remote
1
3
24
5
6
7 8
9
p
q
f
d
s
a
;
o
i
u
y
t
r
e
w
DIGITAL
Parts Identification
Become familiar with the buttons and controls on the receiver before use.
Refer to the pages in parentheses for details.
Remote Control
1 TV/CATV/DBS POWER button (42 44)
2 Source selecting buttons (9)
DVD, CD, TAPE/MD, TV/DBS, PHONO,
FM/AM, VCR
3 SURROUND ON/OFF button (27)
4 SURROUND MODE button (23)
5 DISC button (41)
6 SOUND button (19, 23)
7 On-screen operation buttons (28, 35)
MENU, SET, EXIT,
%, fi, @, #
8 TV VOL +/ buttons (42, 43)
9 Operating buttons for audio/video components
(42 44)
p AUDIO POWER buttons (9)
STANDBY, ON
q VCR POWER button (42 44)
w SLEEP button (16)
e ANALOG/DIGITAL button (13)
r · 10 keys for selecting preset channel (18)
· 10 keys for adjusting sound (23 26)
· 10 keys for operating audio/video
components (41 44)
t Remote control mode selector (9, 41, 43)
y TEXT DISPLAY button (35)
u CHANNEL +/ button (42 44)
i VOLUME +/ button (10)
o MUTING button (11)
Front Panel
1 POWER button and STANDBY lamp (9)
2 Remote sensor (8)
3 DIGITAL SOURCE FORMAT lamps (10)
DOLBY DIGITAL, LINEAR PCM
4 DOLBY SURROUND button and lamp (27)
5 SEA MODE button (19)
6 INPUT ANALOG/DIGITAL button (13)
7 FM/AM TUNING button (17)*
8 FM MODE button (18)
9 Display (9)
p Source lamps (9)
q MASTER VOLUME control (10)
w PHONES jack (11)
e SPEAKERS 1/2 buttons and lamps (10)
r DSP MODE button (23)
t BALANCE/SURROUND ADJUST button
(11, 12, 23)*
y SEA ADJUST button (19)*
u SETTING button (12 15)*
i TUNER/SEA MEMORY button (17 19)
o SOUND SELECT/INPUT ATT. button
(10, 11)
; LOUDNESS/SOURCE NAME button
(11, 12)
a ONE TOUCH OPERATION button and lamp
(16)
s TUNER PRESET button (18)*
d MULTI JOG control
What this control actually does depends on
which function you are trying to adjust. Before
using this control, select the function by
pressing one of the buttons marked with *.
f SOURCE SELECTOR control (9)
RM-SRX778J
REMOTE CONTROL
CONTROL
CHANNEL
VOLUME
TV VOL
TUNING
STOP
PAUSE
FF/
/REW
VCR
TV/VIDEO
TAPE
MUTING
REC
PLAY
DOWN
UP
STANDBY
ON
TV/CATV/DBS
VCR
POWER
POWER
DVD
CD
TAPE/MD
TV/DBS
PHONO
FM/AM
VCR
ANALOG/DIGITAL
SURROUND
CNTR
SURROUND
TEST
REAR-L
DISC
MODE
ON/OFF
EFFECT
REAR-R
SOUND
SEA MODE
SUBWOOFER
RETURN
SET
MENU
AUDIO/
TV/VCR
EXIT
TEXT
DISPLAY
FM MODE/MUTING
SLEEP
12
3
45
6
7/P
89
10
0
+10
100+
CATV/DBS
MENU
ENTER
1
2
3
4
5
6
7
8
9
o
i
u
y
t
r
e
w
q
p
EN01-08.RX-778V[C]/1
99.4.27, 5:09 PM
2
3
English
ANTENNA
AM
EXT
AM
LOOP
FM 75
COAXIAL
AM
LOOP
ANTENNA
AM
EXT
FM
75
COAXIAL
AM
LOOP
AM
EXT
FM
75
COAXIAL
ANTENNA
Getting Started
This section explains how to connect audio/video components and speakers to the receiver, and how to connect the
power supply.
Before Installation
General
· Be sure your hands are dry.
· Turn the power off to all components.
· Read the manuals supplied with the components you are going to
connect.
Locations
· Install the receiver in a location that is level and protected from
moisture.
· The temperature around the receiver must be between 5° and 35°
C (23° and 95° F).
· Make sure there is good ventilation around the receiver. Poor
ventilation could cause overheating and damage the receiver.
Handling the receiver
· Do not insert any metal object into the receiver.
· Do not disassemble the receiver or remove screws, covers, or
cabinet.
· Do not expose the receiver to rain or moisture.
Checking the Supplied Accessories
Check to be sure you have all of the following items, which are
supplied with the receiver.
The number in the parentheses indicates quantity of the pieces
supplied.
· Remote Control (1)
· Batteries (2)
· AM Loop Antenna (1)
· FM Antenna (1)
If anything is missing, contact your dealer immediately.
A. Using the Supplied FM Antenna
The FM antenna provided can be connected to the FM 75
COAXIAL terminal as temporary measure.
B. Using the Standard Type Connector (Not Supplied)
A standard type connector should be connected to the FM 75
COAXIAL terminal.
Note:
If reception is poor, connect the outdoor antenna.
Before attaching a 75
coaxial cable (the kind with a round wire going
to an outdoor antenna), disconnect the supplied FM antenna.
A
B
FM Antenna
Outdoor FM Antenna Cable
Extend the supplied FM antenna horizontally.
Connecting the FM and AM Antennas
FM Antenna Connections
EN01-08.RX-778V[C]/1
99.4.23, 9:03 AM
3