For Customer Use:
Enter below the Model No. and Serial
No. which are located either on the rear,
bottom or side of the cabinet. Retain this
information for future reference.
Model No.
Serial No.
LVT0852-001A
[J]
INSTRUCTIONS
AUDIO/VIDEO CONTROL RECEIVER
RX-7020VBK
DVD
VCR
TV SOUND/DBS
ADJUST
RX-7020V AUDIO/VIDEO CONTROL RECEIVER
SETTING
MASTER VOLUME
CONTROL
DOWN
UP
CD
TAPE/CDR
SOURCE NAME
BASS BOOST
INPUT
ANALOG/DIGITAL
SPEAKERS ON/OFF
SURROUND MODE
PHONES
SURROUND ON/OFF
FM/AM TUNING
STANDBY
STANDBY/ON
FM/AM PRESET
FM MODE
MEMORY
INPUT ATT
FM/AM
DVD MULTI
PHONO
SOURCE NAME
12
COMPULINK
Remote
CONTROL
+
-
+
-
+
-
23
1
56
4
89
7/P
0
+10
10
BASSBOOST EFFECT
MENU
ENTER
TEST
REAR·L +
DIMMER
SUBWOOFER+
REAR·R +
MUTING
CH
TV VOL
/REW
FF/
VOLUME
CATV/DBS
CONTROL
TV/VIDEO
REC
PAUSE
RETURN
FMMODE
100+
CONTROL
A/V CONTROL RECEIVER
RM-SRX7020J REMOTE CONTROL
CATV/DBS
VCR
TV
AUDIO
SURROUND
MODE
INPUT
ON/OFF
DVD MULTI
DVD
CD
TAPE/CDR
TREBLE
TV/DBS
VCR
PHONO
FM/AM
BASS
SURROUND
ANALOG/DIGITAL SLEEP
CENTER +
TUNING
+
-
+
+
-
-
SOUND
RX-7020VBK[J]_COVER
01.12.27, 3:22 PM
1
Caution: Proper Ventilation
To avoid risk of electric shock and fire and to protect from damage.
Locate the apparatus as follows:
Front:
No obstructions open spacing.
Sides:
No obstructions in 10 cm from the sides.
Top:
No obstructions in 10 cm from the top.
Back:
No obstructions in 15 cm from the back.
Bottom:
No obstructions, place on the level surface.
In addition, maintain the best possible air circulation as illustrated.
Attention: Ventilation Correcte
Pour éviter les chocs électriques, l'incendie et tout autre dégât.
Disposer l'appareil en tenant compte des impératifs suivants
Avant:
Rien ne doit gêner le dégagement
Flancs:
Laisser 10 cm de dégagement latéral
Dessus:
Laisser 10 cm de dégagement supérieur
Arrière:
Laisser 15 cm de dégagement arrière
Dessous:
Rien ne doit obstruer par dessous; poser l'appareil sur une
surface plate.
Veiller également à ce que l'air circule le mieux possible comme illustré.
Floor
Plancher
Wall or obstructions
Mur, ou obstruction
CAUTION:
TO REDUCE THE RISK OF ELECTRIC SHOCK.
DO NOT REMOVE COVER (OR BACK)
NO USER SERVICEABLE PARTS INSIDE.
REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.
RISK OF ELECTRIC SHOCK
DO NOT OPEN
The lightning flash with arrowhead symbol,
within an equilateral triangle is intended to
alert the user to the presence of uninsulated
"dangerous voltage" within the product's
enclosure
that
may
be
of
sufficient
magnitude to constitute a risk of electric
shock to persons.
The exclamation point within an equilateral
triangle is intended to alert the user to the
presence
of
important
operating
and
maintenance (servicing) instructions in the
literature accompanying the appliance.
CAUTION
WARNING: TO REDUCE THE RISK OF FIRE
OR ELECTRIC SHOCK, DO NOT EXPOSE
THIS APPLIANCE TO RAIN OR MOISTURE.
Caution STANDBY/ON
button!
Disconnect the mains plug to shut the power off completely. The
STANDBY/ON
button in any position does not disconnect
the mains line. The power can be remote controlled.
Attention Commutateur STANDBY/ON
!
Déconnecter la fiche de secteur pour couper complètement le
courant. Le commutateur STANDBY/ON
ne coupe jamais
complètement la ligne de secteur, quelle que soit sa position. Le
courant peut être télécommandé.
CAUTION
To reduce the risk of electrical shocks, fire, etc.:
1.
Do not remove screws, covers or cabinet.
2.
Do not expose this appliance to rain or moisture.
ATTENTION
Afin d'éviter tout risque d'électrocution, d'incendie, etc.:
1.
Ne pas enlever les vis ni les panneaux et ne pas ouvrir le
coffret de l'appareil.
2.
Ne pas exposer l'appareil à la pluie ni à l'humidité.
Warnings, Cautions and Others/
Mises en garde, précautions et indications diverses
For U.S.A.
This equipment has been tested and found to comply with the limits
for a Class B digital device, pursuant to part 15 of the FCC Rules.
These limits are designed to provide reasonable protection against
harmful interference in a residential installation.
This equipment generates, uses and can radiate radio frequency
energy and, if not installed and used in accordance with the
instructions,
may
cause
harmful
interference
to
radio
communications. However, there is no guarantee that interference
will not occur in a particular installation. If this equipment does cause
harmful interference to radio or television reception, which can be
determined by turning the equipment off and on, the user is
encouraged to try to correct the interference by one or more of the
following measures:
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that
to which the receiver is connected.
Consult the dealer or an experienced radio/TV technician for help.
Changes
or
modifications
not
expressly
approved
by
the
manufacturer for compliance could void the user's authority to
operate the equipment.
For Canada/pour Le Canada
THIS DIGITAL APPARATUS DOES NOT EXCEED THE CLASS
B LIMITS FOR RADIO NOISE EMISSIONS FROM DIGITAL
APPARATUS AS SET OUT IN THE INTERFERENCE-CAUSING
EQUIPMENT STANDARD ENTITLED "DIGITAL APPARATUS,"
ICES-003 OF THE DEPARTMENT OF COMMUNICATIONS.
CET APPAREIL NUMERIQUE RESPECTE LES LIMITES DE
BRUITS RADIOELECTRIQUES APPLICABLES AUX
APPAREILS NUMERIQUES DE CLASSE B PRESCRITES
DANS LA NORME SUR LE MATERIEL BROUILLEUR;
"APPAREILS NUMERIQUES", NMB-003 EDICTEE PAR LE
MINISTRE DES COMMUNICATIONS.
RX-7020VBK
Spacing 15 cm or more
Dégagement de 15 cm ou plus
Stand height
15 cm or more
Hauteur du
socle: 15 cm ou
plus
Front
Avant
For Canada/pour le Canada
CAUTION: TO PREVENT ELECTRIC SHOCK, MATCH WIDE
BLADE OF PLUG TO WIDE SLOT, FULLY INSERT
ATTENTION: POUR EVITER LES CHOCS ELECTRIQUES,
INTRODUIRE LA LAME LA PLUS LARGE DE LA FICHE DANS LA
BORNE CORRESPONDANTE DE LA PRISE ET POUSSER
JUSQUAU FOND
RX-7020VBK[J]_Safety
01.12.27, 3:22 PM
1
1
Table of Contents
Table
of
Contents
Parts Identification ...................................... 2
Getting Started ........................................... 3
Before Installation ...................................................................... 3
Checking the Supplied Accessories ........................................... 3
Putting Batteries in the Remote Control .................................... 3
Connecting the FM and AM Antennas ....................................... 4
Connecting the Speakers ............................................................ 5
Connecting Audio/Video Components ....................................... 6
Connecting the Power Cord ....................................................... 9
Basic Operations ....................................... 10
Turning On the Power .............................................................. 10
Selecting the Source to Play ..................................................... 10
Adjusting the Volume ............................................................... 11
Selecting the Front Speakers .................................................... 11
Listening Only with Headphones ............................................. 12
Turning Off the Sounds Temporarily--Muting ........................ 12
Changing the Display Brightness ............................................. 12
Turning Off the Power with the Sleep Timer ........................... 12
Basic Settings ........................................... 14
Setting the Digital Input (DIGITAL IN) Terminals ................. 14
Selecting the Analog or Digital Input Mode ............................ 15
Selecting the Video Input Terminal .......................................... 16
Setting the Speaker Information ............................................... 16
Sound Adjustments .................................... 19
Attenuating the Input Signal .................................................... 19
Adjusting the Front Speakers Output Balance ......................... 19
Adjusting the Tone ................................................................... 20
Adjusting the Subwoofer Output Level .................................... 20
Reinforcing the Bass ................................................................ 20
Tuner Operations ....................................... 21
Tuning in Stations Manually .................................................... 21
Using Preset Tuning ................................................................. 21
Selecting the FM Reception Mode ........................................... 22
Creating Realistic Sound Fields ................... 23
About Relations between Speaker Layouts and
Surround Modes ................................................................. 25
Using Dolby Pro Logic II, Dolby Digital
and DTS Digital Surround ................................................. 26
Using DAP Modes and All Channel Stereo ............................. 28
Using DVD MULTI Playback Mode ................ 30
Activating DVD MULTI Playback Mode ................................ 30
COMPU LINK Remote Control System ......... 31
AV COMPU LINK Remote Control System .... 32
Operating JVC's Audio/Video
Components .......................................... 34
Operating Audio Components .................................................. 34
Operating Video Components .................................................. 36
Operating Other Manufacturers' Video
Equipment ............................................ 37
Troubleshooting ......................................... 40
Specifications ............................................ 41
This mark indicates that the remote control CAN
ONLY be used for the operation explained.
Remote
NOT
This mark indicates that the remote control CANNOT
be used for the operation explained. Use buttons on
the front panel.
EN01-09.RX-7020V[J]f
01.12.27, 6:36 PM
1
2
Parts Identification
Front Panel
Remote Control
Front Panel
1 STANDBY/ON
button and STANDBY
lamp (10)
2 FM/AM TUNING
5/ buttons (21)
3 FM/AM PRESET
5/ buttons (21, 22)
4 FM MODE button (22)
5 MEMORY button (21, 22)
6 Display (10)
7 ADJUST button (19, 20, 27 29, 30)
8 Remote sensor (3)
9 SETTING button (14, 16 18)
p MASTER VOLUME control (11)
q PHONES jack (12)
w SURROUND ON/OFF button (25, 27, 29)
e SURROUND MODE button (25, 27, 29)
r · INPUT ANALOG/DIGITAL button (15)
· INPUT ATT button (19)
t · SPEAKERS ON/OFF 1 button (11, 12)
· SPEAKERS ON/OFF 2 button (11, 12)
y BASS BOOST button (20)
u SOURCE NAME buttons (11)
i Source selecting buttons
(10, 11, 15, 21, 22, 30)
DVD MULTI, DVD, VCR,
TV SOUND/DBS, CD, TAPE/CDR,
PHONO, FM/AM
o CONTROL UP
5/DOWN buttons
(14, 16 20, 27 29, 30)
Buttons on the Remote Control
Remote Control Operation Mode
FM/AM
TUNER
CD
CD
PHONO
PHONO
TAPE/CDR
TAPE
DVD
DVD
DVD MULTI
DVD
* When you press one of these buttons, the remote control operation mode appears on
the display window.
Buttons on the Remote Control
Remote Control Operation Mode
TV/DBS
TV
VCR
VCR
CATV/DBS CONTROL
DBS
CONTROL
VCR or TAPE
or CDDSC
SOUND
SOUND
1
2
3
4
t
u
y
i
o
;
a
s
d
5
6
7
8
9
p
q
w
r
e
a
b
CONTROL
+
-
+
-
+
-
23
1
56
4
89
7/P
0
+10
10
BASSBOOST
EFFECT
MENU
ENTER
TEST
DIMMER
MUTING
CH
TV VOL
/REW
FF/
VOLUME
CATV/DBS
CONTROL
TV/VIDEO
REC
TUNING
PAUSE
RETURN
FMMODE
100+
CONTROL
A/V CONTROL RECEIVER
RM-SRX7020J REMOTE CONTROL
CATV/DBS
VCR
TV
AUDIO
SURROUND
MODE
INPUT
ON/OFF
DVD MULTI
DVD
CD
TAPE/CDR
TREBLE
TV/DBS
VCR
PHONO
FM/AM
BASS
SURROUND
ANALOG/DIGITAL
SLEEP
+
-
SUBWOOFER+
REAR· R+
REAR· L+
CENTER+
-
-
++
SOUND
Remote Control
1
Display window
a: Remote control operation mode indicator
b: Signal transmission indicator
Lights up when transmitting the remote control
signal.
2
Power buttons (10, 36 39)
CATV/DBS
, VCR
, TV
,
AUDIO
3
Source selecting buttons
(10, 11, 15, 21, 22, 30, 34 39) *
DVD, DVD MULTI, CD, FM/AM, TV/DBS, VCR,
TAPE/CDR, PHONO
4
BASS +/ buttons (20)
5
SURROUND ON/OFF button (25, 26, 28)
6
SURROUND MODE button (25, 26, 28)
7
BASS BOOST button (20)
8
SOUND button (20, 27, 28, 30) *
9
DIMMER button (12)
p
MUTING button (12)
q
CATV/DBS CONTROL button (37) *
w
TV/VIDEO button (36, 37)
e
CH (channel) +/ buttons (36 38)
r
TUNING +/ buttons (21)
t
REC PAUSE button (35, 36, 38)
y
TREBLE +/ buttons (20)
u
SLEEP button (12)
i
ANALOG/DIGITAL INPUT button (15)
o
· 10 keys for selecting preset channels (22)
· 10 keys for adjusting sound (20, 27, 28, 30)
· 10 keys for operating audio/video components
(35 39)
;
TV VOL (volume) +/ buttons (36, 37)
a
VOLUME +/ buttons (11)
s
Operating buttons for audio/video components
(35 38)
d
CONTROL button (34 36) *
ADJUST
RX-7020V AUDIO/VIDEO CONTROL RECEIVER
SETTING
MASTER VOLUME
CONTROL
DOWN
UP
SURROUND MODE
PHONES
SURROUND ON/OFF
FM/AM TUNING
STANDBY
FM/AM PRESET
FM MODE
MEMORY
1
2
5
4
8
79
p
q
w
t
u
io
6
3
STANDBY/ON
DVD
VCR
TV SOUND/DBS
CD
TAPE/CDR
SOURCE NAME
SOURCE NAME
FM/AM
DVD MULTI
PHONO
y
r
e
LC
S.WFR
LS
RS
CH-
S
LFE
SPK
PROLOGIC
DSP H.PHONE
AUTOMUTING
TUNED STEREO
VOLUME
BASS BOOST
INPUT ATT
SLEEP
DIGITAL AUTO
ANALOG
DIGITAL
LINEAR PCM
12
R
BASS BOOST
INPUT
ANALOG/DIGITAL
SPEAKERS ON/OFF
INPUT ATT
12
See pages in the parentheses for details.
EN01-09.RX-7020V[J]f
01.12.27, 3:34 PM
2
3
Getting Started
Before Installation
General Precautions
· DO NOT insert any metal object into the unit.
· DO NOT disassemble the unit or remove screws, covers, or
cabinet.
· DO NOT expose the unit to rain or moisture.
Locations
· Install the unit in a location that is level and protected from
moisture.
· The temperature around the unit must be between 5°C and 35°C
(23°F and 95°F).
· Make sure there is good ventilation around the unit. Poor
ventilation could cause overheating and damage the unit.
Handling the unit
· DO NOT touch the power cord with wet hands.
· DO NOT pull on the power cord to unplug the cord. When
unplugging the cord, always grasp the plug so as not to damage
the cord.
· Keep the power cord away from the connecting cords and the
antenna. The power cord may cause noise or screen interference. It
is recommended to use a coaxial cable for antenna connection,
since it is well-shielded against interference.
· When a power failure occurs, or when you unplug the power cord,
the preset settings such as preset FM/AM channels and sound
adjustments may be erased in a few days.
Checking the Supplied Accessories
Check to be sure you have all of the following supplied accessories.
The number in the parentheses indicates the quantity of the pieces
supplied.
· Remote Control (1)
· Batteries (2)
· AM Loop Antenna (1)
· FM Antenna (1)
If anything is missing, contact your dealer immediately.
Parts
Identification/Getting
Started
Putting Batteries in the Remote Control
Before using the remote control, put two supplied batteries first.
· When using the remote control, aim the remote control directly at
the remote sensor on the unit.
1 On the back of the remote control, remove the
battery cover.
2 Insert batteries.
· Make sure to match the polarity: (+) to (+) and () to ().
3 Replace the cover.
If the range or effectiveness of the remote control decreases, replace
the batteries. Use two R6P(SUM-3)/AA(15F) type dry-cell batteries.
CAUTION:
Follow these precautions to avoid leaking or cracking cells:
· Place batteries in the remote control so they match the polarity:
(+) to (+) and () to ().
· Use the correct type of batteries. Batteries that look similar may
differ in voltage.
· Always replace both batteries at the same time.
· Do not expose batteries to heat or flame.
EN01-09.RX-7020V[J]f
01.12.27, 3:34 PM
3