SERVICE MANUAL
COPYRIGHT © 2005 Victor Company of Japan, Limited
No.MA122
2005/2
CD RECEIVER
MA122
2005
2
KD-AR560,KD-G510
TABLE OF CONTENTS
1
PRECAUTIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-3
2
SPECIFIC SERVICE INSTRUCTIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-5
3
DISASSEMBLY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-6
4
ADJUSTMENT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-25
5
TROUBLESHOOTING . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-26
Area suffix
J ------------- Northern America
ARSENAL rogo
SUB WOOFER OUT
KD-AR560
KD-G510
1-2 (No.MA122)
SPECIFICATION
Design and specifications are subject to change without notice.
AUDIO AMPLIFIER SECTION
Power Output
20 W RMS
× 4 Channels at 4 and - 1% THD+N
Signal to Noise Ratio
80 dBA (reference: 1 W into 4
)
Load Impedance
4
(4 to 8 allowance)
Tone Control Range
Bass
±10 dB at 100Hz
Treble
±10 dB at 10kHz
Frequency Response
40 Hz to 20 000 Hz
Line-Out Level/Impedance KD-AR560
4.0 V/20 k
load (full scale)
KD-G510
2.5 V/20 k
load (full scale)
Output Impedance
1 k
Subwoofer-Out Level/Impedance
2.0 V/20 k
load (full scale)
Other terminals
CD changer, SUBWOOFER
TUNER SECTION
Frequency Range
FM
87.5 MHz to 107.9 MHz (with channel interval set to 200 kHz)
87.5 MHz to 108.0 MHz (with channel interval set to 50 kHz)
AM
530 kHz to 1 710 kHz (with channel interval set to 10 kHz)
531 kHz to 1 602 kHz (with channel interval set to 9 kHz)
[FM Tuner]
Usable Sensitivity
11.3 dBf (1.0
µV/75 )
50 dB Quieting Sensitivity
16.3 dBf (1.8
µV/75 )
Alternate Channel Selectivity (400 kHz) 65 dB
Frequency Response
40 Hz to 15 000 Hz
Stereo Separation
35 dB
Capture Ratio
1.5 dB
[AM Tuner]
Sensitivity
20
µV
Selectivity
35 dB
CD PLAYER SECTION
Type
Compact disc player
Signal Detection System
Non-contact optical pickup (semiconductor laser)
Number of channels
2 channels (stereo)
Frequency Response
5 Hz to 20 000 Hz
Dynamic Range
96 dB
Signal-to-Noise Ratio
98 dB
Wow and Flutter
Less than measurable limit
MP3 decoding format
MPEG1/2 Audio Layer 3
Max. Bit Rate:320 Kbps
WMA (Windows Media Audio) decodingformat
Max. Bit Rate:192 Kbps
GENERAL
Power Requirement
Operating Voltage
DC 14.4 V (11 V to 16 V allowance)
Grounding System
Negative ground
Allowable Operating Temperature
0
°C to +40°C (32°F to 104°F)
Dimensions (W
× H × D)
Installation Size (approx.)
182 mm
× 52 mm × 150 mm (7-3/16" × 2-1/16" × 5-15/16")
Panel Size (approx.)
188 mm
× 58 mm × 11 mm (7-7/16" × 2-5/16" × 7/16")
Mass (approx.)
1.5 kg (3.4 lbs) (excluding accessories)
(No.MA122)1-3
SECTION 1
PRECAUTIONS
1.1
Safety Precautions
!
Burrs formed during molding may be left over on some parts of the chassis. Therefore,
pay attention to such burrs in the case of preforming repair of this system.
!
Please use enough caution not to see the beam directly or touch it in case of an
adjustment or operation check.
1-4 (No.MA122)
1.2
Preventing static electricity
Electrostatic discharge (ESD), which occurs when static electricity stored in the body, fabric, etc. is discharged, can destroy the laser
diode in the traverse unit (optical pickup). Take care to prevent this when performing repairs.
1.2.1
Grounding to prevent damage by static electricity
Static electricity in the work area can destroy the optical pickup (laser diode) in devices such as CD players.
Be careful to use proper grounding in the area where repairs are being performed.
(1) Ground the workbench
Ground the workbench by laying conductive material (such as a conductive sheet) or an iron plate over it before placing the
traverse unit (optical pickup) on it.
(2) Ground yourself
Use an anti-static wrist strap to release any static electricity built up in your body.
(3) Handling the optical pickup
· In order to maintain quality during transport and before installation, both sides of the laser diode on the replacement optical
pickup are shorted. After replacement, return the shorted parts to their original condition.
(Refer to the text.)
· Do not use a tester to check the condition of the laser diode in the optical pickup. The tester's internal power source can easily
destroy the laser diode.
1.3
Handling the traverse unit (optical pickup)
(1) Do not subject the traverse unit (optical pickup) to strong shocks, as it is a sensitive, complex unit.
(2) Cut off the shorted part of the flexible cable using nippers, etc. after replacing the optical pickup. For specific details, refer to the
replacement procedure in the text. Remove the anti-static pin when replacing the traverse unit. Be careful not to take too long a
time when attaching it to the connector.
(3) Handle the flexible cable carefully as it may break when subjected to strong force.
(4) It is not possible to adjust the semi-fixed resistor that adjusts the laser power. Do not turn it.
1.4
Attention when traverse unit is decomposed
*Please refer to "Disassembly method" in the text for the CD pickup unit.
· Apply solder to the short land before the flexible wire is disconnected from the connector on the CD pickup unit.
(If the flexible wire is disconnected without applying solder, the CD pickup may be destroyed by static electricity.)
· In the assembly, be sure to remove solder from the short land after connecting the flexible wire.
1M
(caption)
Anti-static wrist strap
Conductive material
(conductive sheet) or iron plate
Pickup
Short-circuit point
(Soldering)
Flexible wire
(No.MA122)1-5
SECTION 2
SPECIFIC SERVICE INSTRUCTIONS
2.1
HOW TO IDENTIFY MODELS
2.1.1 NAME PLATE
Discernment sign (as same as KD-AR560)