JVC HRXV2EX/EY/EL - Service Manual Immediate Download

SERVICE MANUAL

General

Power requirements

AC 200-240V, 50/60 Hz

Power consumption

Operation mode : 23W

Standby mode : 6.7W

Dimensions (approx.)

430 X 97.5 X 293 mm (w/h/d)

Mass (approx.

.8 kg

Operating temperatur

°C to 35°C (41°F to 95°F)

Operating humidity

5 % to 90 %

Timer

24 hours display tape

Program capacity

1 month 7 program

RF Modulator

UHF 22-68 (Adjustable)

System

Laser

Semiconductor laser, wavelength 650 nm

Video Head system

Double azimuth 4 heads, helical scanning.

Signal system

PAL

Frequency response

DVD (PCM 96 kHz): 8 Hz to 44 kHz

DVD (PCM 48 kHz): 8 Hz to 22 kHz

CD: 8 Hz to 20 kHz

Signal-to-noise ratio

More than 100dB (ANALOG OUT connectors only)

Harmonic distortion

Less than 0.008%

Dynamic range

More than 100 dB (DVD)

More than 95 dB (CD)

Inputs (VCR)

Audi

6.0dBm, more than 10 kohms (SCART)

-6.0dBm, more than 47 kohms (RCA)

Video

1.0 Vp-p, 75 ohms, unbalanced (SCART/RCA)

Outputs (DVD)

S-VIDEO OUT

(Y) 1.0 Vp-p 75 ohms, negative sync., Mini Din 4-pin x 1

COMPONENT VIDEO OUT

(Y) 1.0 V (p-p), 75

, negative sync, RCA jack x 1

(Pb)/(Pr) 0.7 V (p-p), 75

, RCA jack x 2

Audio output (digital audio)

0.5 V (p-p), 75

, RCA jack x 1

Audio output (optical audio)

5 V (p-p), 75

, Optical connector x 1

Audio output (analog audio)

2.0 Vrms (1 kHz, 0 dB), 330

, RCA jack (L, R) x 2/SCART(TO TV)

Outputs (VCR)

Audi

6.0dBm, less than 1 kohms (SCART)

Video

1.0Vp-p, 75 ohms, unbalanced (SCART)

Design and specifications are subject to change without notice.

Manufactured under license from Dolby Laboratories. " Dolby" and double-D symbol are trademarks of

Manufactured under license from Digital Theater Systems, Inc. US Pat. No. 5,451,942 and other world-wide patents issued and

No.82984

2003/06

HR-XV2EX, HR-XV2EY,

HR-XV2EL, HR-XV11EX

HR-XV2EX,HR-XV2EY,HR-XV2EL,HR-XV11EX D2VP11

DVD PLAYER /VIDEO CASSETTE RECORDER

SPECIFICATIONS (The specifications shown pertain specifically to the model HR-XV2E.)

PAL

VCR

DVD

POWER

DVDMENU MEMORY

SUBTITLE

ANGLE

REPEATA-B

ZOOM

TITLE

REPEAT

SHOWVIEW

VIDEOPlus+

TV/VCR

TV/VCR PR +

CANCEL

TV/VCR PR

0000

AUDIO

MONITOR

PROG.

RANDO

DISPLAY

EJECT

RETURN

AUX

CONTENTS

SECTION 1 . . . . SUMMARY

SECTION 3 . . . . ELECTRICAL

SECTION 4 . . . . MECHANISM OF VCR PART

SECTION 5 . . . . MECHANISM OF DVD PART

SECTION 6 . . . . REPLACEMENT PARTS LIST

SECTION 1

SUMMARY

CONTENTS

Important Safety Precautions

SPECIFICATIONS ................................................................................................... 1-5

Important Safety Precautions

Prior to shipment from the factory, JVC products are strictly inspected to conform with the recognized product safety and electrical codes

of the countries in which they are to be sold. However, in order to maintain such compliance, it is equally important to implement the

following precautions when a set is being serviced.

Fig.1

1. Locations requiring special caution are denoted by labels and

inscriptions on the cabinet, chassis and certain parts of the

product. When performing service, be sure to read and com-

ply with these and other cautionary notices appearing in the

operation and service manuals.

2. Parts identified by the

symbol and shaded (

) parts are

critical for safety.

Replace only with specified part numbers.

Note: Parts in this category also include those specified to com-

ply with X-ray emission standards for products using

cathode ray tubes and those specified for compliance

with various regulations regarding spurious radiation

emission.

3. Fuse replacement caution notice.

Caution for continued protection against fire hazard.

Replace only with same type and rated fuse(s) as specified.

4. Use specified internal wiring. Note especially:

1) Wires covered with PVC tubing

2) Double insulated wires

3) High voltage leads

5. Use specified insulating materials for hazardous live parts.

Note especially:

1) Insulation Tape

3) Spacers

5) Barrier

2) PVC tubing

4) Insulation sheets for transistors

6. When replacing AC primary side components (transformers,

power cords, noise blocking capacitors, etc.) wrap ends of

wires securely about the terminals before soldering.

Power cord

Fig.2

10. Also check areas surrounding repaired locations.

11. Products using cathode ray tubes (CRTs)

In regard to such products, the cathode ray tubes themselves,

the high voltage circuits, and related circuits are specified for

compliance with recognized codes pertaining to X-ray emission.

Consequently, when servicing these products, replace the cath-

ode ray tubes and other parts with only the specified parts.

Under no circumstances attempt to modify these circuits.

Unauthorized modification can increase the high voltage value

and cause X-ray emission from the cathode ray tube.

12. Crimp type wire connector

In such cases as when replacing the power transformer in sets

where the connections between the power cord and power

transformer primary lead wires are performed using crimp type

connectors, if replacing the connectors is unavoidable, in or-

der to prevent safety hazards, perform carefully and precisely

according to the following steps.

1) Connector part number : E03830-001

2) Required tool : Connector crimping tool of the proper type

which will not damage insulated parts.

3) Replacement procedure

(1) Remove the old connector by cutting the wires at a point

close to the connector.

Important : Do not reuse a connector (discard it).

Fig.7

cut close to connector

Fig.3

(2) Strip about 15 mm of the insulation from the ends of

the wires. If the wires are stranded, twist the strands to

avoid frayed conductors.

15 mm

Fig.4

(3) Align the lengths of the wires to be connected. Insert

the wires fully into the connector.

Connector

Metal sleeve

Fig.5

(4) As shown in Fig.6, use the crimping tool to crimp the

metal sleeve at the center position. Be sure to crimp fully

to the complete closure of the tool.

Precautions during Servicing

7. Observe that wires do not contact heat producing parts

(heatsinks, oxide metal film resistors, fusible resistors, etc.)

8. Check that replaced wires do not contact sharp edged or

pointed parts.

9. When a power cord has been replaced, check that 10-15 kg of

force in any direction will not loosen it.

1.25

2.0

5.5

Crimping tool

Fig.6

(5) Check the four points noted in Fig.7.

Not easily pulled free

Crimped at approx. center

of metal sleeve

Conductors extended

Wire insulation recessed

more than 4 mm

S40888-01

Safety Check after Servicing

Examine the area surrounding the repaired location for damage or deterioration. Observe that screws, parts and wires have been

returned to original positions, Afterwards, perform the following tests and confirm the specified values in order to verify compli-

ance with safety standards.

1. Insulation resistance test

Confirm the specified insulation resistance or greater between power cord plug prongs and

externally exposed parts of the set (RF terminals, antenna terminals, video and audio input

and output terminals, microphone jacks, earphone jacks, etc.). See table 1 below.

2. Dielectric strength test

Confirm specified dielectric strength or greater between power cord plug prongs and exposed

accessible parts of the set (RF terminals, antenna terminals, video and audio input and output

terminals, microphone jacks, earphone jacks, etc.). See table 1 below.

3. Clearance distance

When replacing primary circuit components, confirm specified clearance distance (d), (d') be-

tween soldered terminals, and between terminals and surrounding metallic parts. See table 1

below.

4. Leakage current test

Confirm specified or lower leakage current between earth ground/power cord plug prongs

and externally exposed accessible parts (RF terminals, antenna terminals, video and audio

input and output terminals, microphone jacks, earphone jacks, etc.).

Measuring Method : (Power ON)

Insert load Z between earth ground/power cord plug prongs and externally exposed accessi-

ble parts. Use an AC voltmeter to measure across both terminals of load Z. See figure 9 and

following table 2.

5. Grounding (Class 1 model only)

Confirm specified or lower grounding impedance between earth pin in AC inlet and externally exposed accessible parts (Video in,

Video out, Audio in, Audio out or Fixing screw etc.).

Measuring Method:

Connect milli ohm meter between earth pin in AC inlet and exposed accessible parts. See figure 10 and grounding specifications.

Chassis

Power cord,

primary wire

Region

USA & Canada

Europe & Australia

Grounding Impedance (Z)

0.1 ohm

0.5 ohm

AC inlet

Earth pin

Exposed accessible part

Milli ohm meter

Grounding Specifications

Fig. 10

Externally

exposed

accessible part

Fig. 9

Fig. 8

Clearance Distance (d), (d')

d, d'

3 mm

d, d'

4 mm

d, d'

3.2 mm

1 M

R 12 M/500 V DC

Dielectric Strength

AC 1 kV 1 minute

AC 1.5 kV 1 miute

AC 1 kV 1 minute

AC Line Voltage

100 V

100 to 240 V

110 to 130 V

200 to 240 V

Japan

USA & Canada

Europe & Australia

10 M

/500 V DC

Region

Insulation Resistance (R)

1 M

/500 V DC

AC 3 kV 1 minute

(Class

AC 1.5 kV 1 minute

(Class

4 mm

8 mm (Power cord)

6 mm (Primary wire)

Table 1 Specifications for each region

a, b, c

Leakage Current (i)

AC Line Voltage

100 V

110 to 130 V

220 to 240 V

Japan

USA & Canada

1 mA rms

Exposed accessible parts

Antenna earth terminals

Other terminals

0.5 mA rms

0.7 mA peak

2 mA dc

0.7 mA peak

2 mA dc

Europe & Australia

Region

Load Z

1 k

2 k

1.5 k

0.15

µF

50 k

Table 2 Leakage current specifications for each region

Note: These tables are unofficial and for reference only. Be sure to confirm the precise values for your particular country and locality.

S40888-01