JVC GRDX95US - Service Manual Immediate Download

SERVICE MANUAL

For disassembling and assembling of MECHANISM ASSEMBLY, refer to the SERVICE MANUAL No.86700(MECHANISM ASSEMBLY).

Digital Still Camera Function

Storage media

: SD Memory Card/MultiMediaCard

Compression

system

: Still image

: JPEG

(compatible)

Moving image : MPEG4

(compatible)

File size

: 4 modes (1600 x 1200 pixels*,

1280 x 960 pixels*,

1024 x 768 pixels,

640 x 480 pixels)

Picture quality

: 2 modes (FINE/STANDARD)

Approximate

number of

storable images :

pg. 18.

* GR-DX300 only.

Connectors

S/AV

S-Video output

: Y : 1 V (p-p), 75

, analog

C : 0.29 V (p-p), 75

, analog

S-Video input

: Y : 0.8 V (p-p) 1.2 V (p-p), 75

analog

C : 0.2 V (p-p) 0.4 V (p-p), 75

analog

Video output

: 1 V (p-p), 75

, analog

Video input

: 0.8 V (p-p) 1.2 V (p-p), 75

analog

Audio output

: 300 mV (rms), 1 k

, analog,

stereo

Audio input

: 300 mV (rms), 50 k

, analog,

stereo

Edit

: ø3.5 mm (0.14"), 2-pole

Output

: 4-pin, IEEE 1394 compliant

Input

: 4-pin, IEEE 1394 compliant

USB

: 5-pin

AC Adapter

Power requirement

U.S.A and Canada : AC 120 V`, 60 Hz

Other countries

: AC 110 V to 240 V`, 50 Hz/60 Hz

Output

: DC 11 V

, 1 A

Specifications shown are for SP mode unless otherwise indicated. E & O.E. Design and specifications subject

to change without notice.

Camcorder

General

Power supply

: DC 11.0 V

(Using AC Adapter)

DC 7.2 V

(Using battery pack)

Power consumption

LCD monitor off,

viewfinder on : Approx. 3.4 W

LCD monitor on,

viewfinder off : Approx. 4.6 W

Dimensions

(W x H x D)

: 55 mm x 102 mm x 96 mm (2-1/4"

x 4-1/16" x 3-13/16")

(with the LCD monitor closed and

the viewfinder pushed back in)

Weight

: Approx. 440 g (0.97lbs) (without

grip belt) (GR-DX300)

Approx. 450 g (1lbs) (without grip

belt) (GR-DX95/DX75)

Operating

temperature

°C to 40°C (32°F to 104°F)

Operating

humidity

: 35% to 80%

Storage

temperature

: 20

°C to 50°C (4°F to 122°F)

Pickup

: 1/4" CCD (GR-DX300)

1/6" CCD (GR-DX95/DX75)

Lens

: F 1.8, f = 3.8 mm to 38 mm (0.15"

to 1.5"),

10:1 power zoom lens

(GR-DX300)

F1.6, f =2.7 mm to 43.2 mm (0.11"

to 1.7"),

16:1 power zoom lens

(GR-DX95/DX75)

Filter diameter

: ø30.5 mm (1.2")

LCD monitor

: 3" diagonally measured, LCD

panel/TFT active matrix system

(GR-DX300/DX95)

2.5" diagonally measured, LCD

panel/TFT active matrix system

(GR-DX75)

Viewfinder

: Electronic viewfinder with 0.24"

black/white LCD

Speaker

: Monaural

Digital Video Camera

Format

: DV format (SD mode)

Signal format

: NTSC standard

Recording/

Playback format : Video: Digital component recording

: Audio: PCM digital recording,

32 kHz 4-channel (12-bit),

48 kHz 2-channel (16-bit)

Cassette

: Mini DV cassette

Tape speed

: SP : 18.8 mm/s

LP : 12.5 mm/s

Maximum

recording time

: SP : 80 min.

(using 80 min.

LP : 120 min.

cassette)

No.86757

2003/06

GR-DX75US, GR-DX95US

GR-DX75US M3D327

GR-DX95US M3D337

DIGITAL VIDEO CAMERA

SPECIFICATIONS (The specifications shown pertain specifically to the model GR-DX75US, GR-DX95US and GR-DX300US.)

CONTENTS

Important Safety Precautions

DISASSEMBLY ............................................................................................................................................................... 1-1

ADJUSTMENT ................................................................................................................................................................ 3-1

CHARTS AND DIAGRAMS ............................................................................................................................................ 4-1

PARTS LIST .................................................................................................................................................................... 5-1

The following table indicate main different points between models GR-DX75US and GR-DX95US.

DIFFERENT LIST

DIFFERENT TABLE OF FEATURE

Notes: Mark

is same as left.

MODEL

GR-DX75US

ITEM

LCD MONITOR

2.5 INCH

3.0 INCH

MEMORY CARD

OPTIONAL

PROVIDED(MMC 8MB)

GR-DX95US

Important Safety Precautions

Prior to shipment from the factory, JVC products are strictly inspected to conform with the recognized product safety and electrical codes

of the countries in which they are to be sold. However, in order to maintain such compliance, it is equally important to implement the

following precautions when a set is being serviced.

Fig.1

1. Locations requiring special caution are denoted by labels and

inscriptions on the cabinet, chassis and certain parts of the

product. When performing service, be sure to read and com-

ply with these and other cautionary notices appearing in the

operation and service manuals.

2. Parts identified by the

symbol and shaded (

) parts are

critical for safety.

Replace only with specified part numbers.

Note: Parts in this category also include those specified to com-

ply with X-ray emission standards for products using

cathode ray tubes and those specified for compliance

with various regulations regarding spurious radiation

emission.

3. Fuse replacement caution notice.

Caution for continued protection against fire hazard.

Replace only with same type and rated fuse(s) as specified.

4. Use specified internal wiring. Note especially:

1) Wires covered with PVC tubing

2) Double insulated wires

3) High voltage leads

5. Use specified insulating materials for hazardous live parts.

Note especially:

1) Insulation Tape

3) Spacers

5) Barrier

2) PVC tubing

4) Insulation sheets for transistors

6. When replacing AC primary side components (transformers,

power cords, noise blocking capacitors, etc.) wrap ends of

wires securely about the terminals before soldering.

Power cord

Fig.2

10. Also check areas surrounding repaired locations.

11. Products using cathode ray tubes (CRTs)

In regard to such products, the cathode ray tubes themselves,

the high voltage circuits, and related circuits are specified for

compliance with recognized codes pertaining to X-ray emission.

Consequently, when servicing these products, replace the cath-

ode ray tubes and other parts with only the specified parts.

Under no circumstances attempt to modify these circuits.

Unauthorized modification can increase the high voltage value

and cause X-ray emission from the cathode ray tube.

12. Crimp type wire connector

In such cases as when replacing the power transformer in sets

where the connections between the power cord and power

transformer primary lead wires are performed using crimp type

connectors, if replacing the connectors is unavoidable, in or-

der to prevent safety hazards, perform carefully and precisely

according to the following steps.

1) Connector part number : E03830-001

2) Required tool : Connector crimping tool of the proper type

which will not damage insulated parts.

3) Replacement procedure

(1) Remove the old connector by cutting the wires at a point

close to the connector.

Important : Do not reuse a connector (discard it).

Fig.7

cut close to connector

Fig.3

(2) Strip about 15 mm of the insulation from the ends of

the wires. If the wires are stranded, twist the strands to

avoid frayed conductors.

15 mm

Fig.4

(3) Align the lengths of the wires to be connected. Insert

the wires fully into the connector.

Connector

Metal sleeve

Fig.5

(4) As shown in Fig.6, use the crimping tool to crimp the

metal sleeve at the center position. Be sure to crimp fully

to the complete closure of the tool.

Precautions during Servicing

7. Observe that wires do not contact heat producing parts

(heatsinks, oxide metal film resistors, fusible resistors, etc.)

8. Check that replaced wires do not contact sharp edged or

pointed parts.

9. When a power cord has been replaced, check that 10-15 kg of

force in any direction will not loosen it.

1.25

2.0

5.5

Crimping tool

Fig.6

(5) Check the four points noted in Fig.7.

Not easily pulled free

Crimped at approx. center

of metal sleeve

Conductors extended

Wire insulation recessed

more than 4 mm

S40888-01

Safety Check after Servicing

Examine the area surrounding the repaired location for damage or deterioration. Observe that screws, parts and wires have been

returned to original positions, Afterwards, perform the following tests and confirm the specified values in order to verify compli-

ance with safety standards.

1. Insulation resistance test

Confirm the specified insulation resistance or greater between power cord plug prongs and

externally exposed parts of the set (RF terminals, antenna terminals, video and audio input

and output terminals, microphone jacks, earphone jacks, etc.). See table 1 below.

2. Dielectric strength test

Confirm specified dielectric strength or greater between power cord plug prongs and exposed

accessible parts of the set (RF terminals, antenna terminals, video and audio input and output

terminals, microphone jacks, earphone jacks, etc.). See table 1 below.

3. Clearance distance

When replacing primary circuit components, confirm specified clearance distance (d), (d') be-

tween soldered terminals, and between terminals and surrounding metallic parts. See table 1

below.

4. Leakage current test

Confirm specified or lower leakage current between earth ground/power cord plug prongs

and externally exposed accessible parts (RF terminals, antenna terminals, video and audio

input and output terminals, microphone jacks, earphone jacks, etc.).

Measuring Method : (Power ON)

Insert load Z between earth ground/power cord plug prongs and externally exposed accessi-

ble parts. Use an AC voltmeter to measure across both terminals of load Z. See figure 9 and

following table 2.

5. Grounding (Class 1 model only)

Confirm specified or lower grounding impedance between earth pin in AC inlet and externally exposed accessible parts (Video in,

Video out, Audio in, Audio out or Fixing screw etc.).

Measuring Method:

Connect milli ohm meter between earth pin in AC inlet and exposed accessible parts. See figure 10 and grounding specifications.

Chassis

Power cord,

primary wire

Region

USA & Canada

Europe & Australia

Grounding Impedance (Z)

0.1 ohm

0.5 ohm

AC inlet

Earth pin

Exposed accessible part

Milli ohm meter

Grounding Specifications

Fig. 10

Externally

exposed

accessible part

Fig. 9

Fig. 8

Clearance Distance (d), (d')

d, d'

3 mm

d, d'

4 mm

d, d'

3.2 mm

1 M

R 12 M/500 V DC

Dielectric Strength

AC 1 kV 1 minute

AC 1.5 kV 1 miute

AC 1 kV 1 minute

AC Line Voltage

100 V

100 to 240 V

110 to 130 V

200 to 240 V

Japan

USA & Canada

Europe & Australia

10 M

/500 V DC

Region

Insulation Resistance (R)

1 M

/500 V DC

AC 3 kV 1 minute

(Class

AC 1.5 kV 1 minute

(Class

4 mm

8 mm (Power cord)

6 mm (Primary wire)

Table 1 Specifications for each region

a, b, c

Leakage Current (i)

AC Line Voltage

100 V

110 to 130 V

220 to 240 V

Japan

USA & Canada

1 mA rms

Exposed accessible parts

Antenna earth terminals

Other terminals

0.5 mA rms

0.7 mA peak

2 mA dc

0.7 mA peak

2 mA dc

Europe & Australia

Region

Load Z

1 k

2 k

1.5 k

0.15

µF

50 k

Table 2 Leakage current specifications for each region

Note: These tables are unofficial and for reference only. Be sure to confirm the precise values for your particular country and locality.

S40888-01

1-1

SECTION 1

DISASSEMBLY

1.1 Before disassembling

1.1.1

Precaution

Be sure to disconnect the power supply unit prior to mount-

ing and soldering of parts.

Prior to removing a component part that needs to discon-

nect its connector(s) and its screw(s), first disconnect the

wire(s) from the connector(s), and then remove the screw(s).

Be careful not to damage the connector and wire etc. dur-

ing connection and disconnection.

When connecting the flat wire to the connector, be careful

with the flat wire direction.

Be careful in removing or handling the part to which some

spacer or shield is attached for reinforcement or insulation.

When replacing chip parts (especially IC parts), first remove

the solder completely to prevent peeling of the pattern.

Tighten screws properly during the procedures. Unless

specified otherwise, tighten screws at a torque of 0.078Nom

(0.8kgfocm).

The bracketed ( ) WR of the connector symbol are assigned

nos. in priority order and do not correspond to those on the

spare parts list.

1.1.2 Disconnection of connectors (wires)

· Torque driver

Be sure to use to fastening the mechanism and exterior parts

because those parts must strictly be controlled for tighten-

ing torque.

· Bit

This bit is slightly longer than those set in conventional torque

drivers.

· Tweezers

To be used for removing and installing parts and wires.

· Chip IC replacement jig

To be used for replacement of IC.

· Cleaning cloth

Recommended the Cleaning cloth to wipe down the video

heads, mechanism (tape transport system), optical lens sur-

face.

FPC connector

Flat wire

FPC connector

lock

Flat wire

B-B connector

· Extend the locks in the direction of the arrow for

unlocking and then pull out the wire. After re-

moving the wire, immediately restore the locks

to their original positions because the locks are

apt to come off the connector.

· Pull both ends of the connector in the arrow

direction, remove the lock and disconnect

the flat wire.

· Pull the board by both the sides in the direction of

the arrow for disconnecting the B-B connector.

Fig. 1-1-2a CONNECTOR

1.1.3

Required disassembling tools

Cleaning cloth

KSMM-01

Torque driver

YTU94088

Bit

YTU94088-003

Chip IC replacement jig

PTS40844-2

Tweezers

P-895

Fig. 1-1-3a

1.2 Removing the major parts

1.2.1 How to read the procedure table

This table shows the steps for disassembly of the major parts.

Reverse these steps when re-assembling them.

(*1) Order of steps in Procedure

When reassembling, perform the step(s) in the reverse or-

der.

(*2) Part name to be removed or installed.

(*3) Fig. No. showing procedure or part location.

(*4) Identification of part to be removed, unhooked, unlocked,

released, unplugged, unclamped or unsoldered.

P= Spring, W= Washer, S= Screw, L= Locking tab, SD=

Solder, CN**(WR**)= Remove the wire (WR**) from the con-

nector (CN**).

(*5) Adjustment information for installation

(*1)

(*2)

(*3)

(*4)

(*5)

Step

No.

Part Name

Fig. No.

Point

Note

[1]

Top cover,

1-3a 4(S1a),(S1b),3(L1a),

2(SD1a),(P1a),(W1a),

CN1(WR1a),

Bracket

2(S1c)

--------------------------