JVC AV14F33/PH - Service Manual Immediate Download

No.52021

Jul. 2002

AV-14F13

AV-14F33

Jul. 2002

AV-14F13

/PH

AV-14F33

/PH

CONTENTS

SPECIFICATIONS

! SAFETY PRECAUTIONS

! FEATURES

MAIN DIFFERENCE LIST

! FUNCTIONS

SPECIFIC SERVICE INSTRUCTIONS

SERVICE ADJUSTMENTS

! PARTS LIST

OPERATING INSTRUCTIONS

STANDARD CIRCUIT DIAGRAM (APPENDIX)

2-1

SERVICE MANUAL

COLOR TELEVISION

BASIC CHASSIS

GA2

RM-C372GY

[AV-14F13/PH]

RM-C373GY

[AV-14F33/PH]

No.52021

AV-14F13

AV-14F33

SPECIFICATIONS

Contents

Items

AV-14F13/PH

AV-14F33/PH

Dimensions (W×

H×

462mm×340.5mm×375mm

Mass

10kg

TV RF System

CCIR (M)&(N)

Color / Sound System

NTSC / PAL-M / PAL-N

BTSC (Multi Channel Sound)

TV Receiving Channels

and Frequency

VL Band

VH Band

UHF Band

(0206) 54MHz88MHz

(0713) 174MHz216MHz

(1469) 470MHz806MHz

CATVReceivingChannels

and Frequency

Low Band

High Band

Mid Band

Super Band

Hyper Band

Ultra Band

Sub Mid Band

(0206)

(0713)

(1422)

(2336)

(3764)

(6594, 100125)

(01, 9699)

TV/CATV Total Channel

181 Channels

Intermediate Frequency

Video IF Carrier

Sound IF Carrier

45.75MHz

41.25MHz (4.5MHz)

Color Sub Carrier

NTSC

: 3.579545MHz

PAL-M

: 3.57561149MHz

PAL-N

: 3.58205625MHz

Antenna terminal

75(VHF/UHF) Terminal, F-Type Connector

Power Input

Rated Voltage

Operating Voltage

110V240V AC, 50Hz/60Hz

90V260V AC, 50Hz/60Hz

Power Consumption

42W

44W

Picture Tube (measured diagonally)

Picture tube 36cm

Visible aria 34cm

High Voltage

22.5kV±1.0kV (at zero beam current)

Speaker

5cm×12cm Oval type×2 (monaural)

5×12cm Oval type×2 (stereo)

Audio Power Output

2W (monaural)

1.5W+1.5W (stereo)

Input

Video input

Audio input

1Vp-p, 75 (RCA pin jack)

500mVrms (-4dBs), High impedance

(RCA pin jack)

Output

Video output

Audio output

1Vp-p, 75

500mVrms (-4dBs), Low impedance

Headphone Jack

Stereo mini jack (dia. 3.5mm, Sound is Monaural)

Stereo mini jack (dia. 3.5mm, Sound is Stereo)

Remote Control Unit

RM-C372GY

(AA/R6/UM-3 battery×2)

RM-C373GY

(AA/R6/UM-3 battery×2)

Design & specifications are subject to change without notice.

(54MHz804MHz)

No.52021

AV-14F13

AV-14F33

SAFETY PRECAUTIONS

1. The design of this product contains special hardware, many

circuits and components specially for safety purposes. For

continued protection, no changes should be made to the original

design unless authorized in writing by the manufacturer.

Replacement parts must be identical to those used in the original

circuits. Service should be performed by qualified personnel

only.

2. Alterations of the design or circuitry of the products should not be

made. Any design alterations or additions will void the

manufacturer's warranty and will further relieve the manufacturer

of responsibility for personal injury or property damage resulting

therefrom.

3. Many electrical and mechanical parts in the products have

special safety-related characteristics. These characteristics are

often not evident from visual inspection nor can the protection

afforded by them necessarily be obtained by using replacement

components rated for higher voltage, wattage, etc. Replacement

parts which have these special safety characteristics are

identified in the parts list of Service manual. Electrical

components having such features are identified by shading

on the schematics and by (!

) on the parts list in Service

manual. The use of a substitute replacement which does not

have the same safety characteristics as the recommended

replacement part shown in the parts list of Service manual may

cause shock, fire, or other hazards.

4. Don't short between the LIVE side ground and ISOLATED

(NEUTRAL) side ground or EARTH side ground when

repairing.

Some model's power circuit is partly different in the GND. The

difference of the GND is shown by the LIVE : (") side GND, the

ISOLATED(NEUTRAL) : (#) side GND and EARTH : ($) side

GND. Don't short between the LIVE side GND and

ISOLATED(NEUTRAL) side GND or EARTH side GND and

never measure with a measuring apparatus (oscilloscope etc.)

the LIVE side GND and ISOLATED(NEUTRAL) side GND or

EARTH side GND at the same time.

If above note will not be kept, a fuse or any parts will be broken.

5. If any repair has been made to the chassis, it is recommended

that the B1 setting should be checked or adjusted (See

ADJUSTMENT OF B1 POWER SUPPLY).

6. The high voltage applied to the picture tube must conform with

that specified in Service manual. Excessive high voltage can

cause an increase in X-Ray emission, arcing and possible

component damage, therefore operation under excessive high

voltage conditions should be kept to a minimum, or should be

prevented. If severe arcing occurs, remove the AC power

immediately and determine the cause by visual inspection

(incorrect installation, cracked or melted high voltage harness,

poor soldering, etc.). To maintain the proper minimum level of

soft X-Ray emission, components in the high voltage circuitry

including the picture tube must be the exact replacements or

alternatives approved by the manufacturer of the complete

product.

7. Do not check high voltage by drawing an arc. Use a high voltage

meter or a high voltage probe with a VTVM. Discharge the

picture tube before attempting meter connection, by connecting

a clip lead to the ground frame and connecting the other end of

the lead through a 10k

2W resistor to the anode button.

8. When service is required, observe the original lead dress. Extra

precaution should be given to assure correct lead dress in the

high voltage circuit area. Where a short circuit has occurred,

those components that indicate evidence of overheating should

be replaced. Always use the manufacturer's replacement

components.

9. Isolation Check

(Safety for Electrical Shock Hazard)

After re-assembling the product, always perform an isolation

check on the exposed metal parts of the cabinet (antenna

terminals, video/audio input and output terminals, Control knobs,

metal cabinet, screw heads, earphone jack, control shafts, etc.)

to be sure the product is safe to operate without danger of

electrical shock.

(1) Dielectric Strength Test

The isolation between the AC primary circuit and all metal parts

exposed to the user, particularly any exposed metal part having a

return path to the chassis should withstand a voltage of 3000V

AC (r.m.s.) for a period of one second.

(. . . . Withstand a voltage of 1100V AC (r.m.s.) to an appliance

rated up to 120V, and 3000V AC (r.m.s.) to an appliance rated

200V or more, for a period of one second.)

This method of test requires a test equipment not generally found

in the service trade.

(2) Leakage Current Check

Plug the AC line cord directly into the AC outlet (do not use a line

isolation transformer during this check.). Using a "Leakage

Current Tester", measure the leakage current from each exposed

metal part of the cabinet, particularly any exposed metal part

having a return path to the chassis, to a known good earth

ground (water pipe, etc.). Any leakage current must not exceed

0.5mA AC (r.m.s.).

However, in tropical area, this must not exceed 0.2mA AC

(r.m.s.).

Alternate Check Method

Plug the AC line cord directly into the AC outlet (do not use a line

isolation transformer during this check.). Use an AC voltmeter

having 1000 ohms per volt or more sensitivity in the following

manner. Connect a 1500

10W resistor paralleled by a 0.15µF

AC-type capacitor between an exposed metal part and a known

good earth ground (water pipe, etc.). Measure the AC voltage

across the resistor with the AC voltmeter. Move the resistor

connection to each exposed metal part, particularly any exposed

metal part having a return path to the chassis, and measure the

AC voltage across the resistor. Now, reverse the plug in the AC

outlet and repeat each measurement. Any voltage measured

must not exceed 0.75V AC (r.m.s.). This corresponds to 0.5mA

AC (r.m.s.).

However, in tropical area, this must not exceed 0.3V AC (r.m.s.).

This corresponds to 0.2mA AC (r.m.s.).

0.15F AC-TYPE

1500 10W

GOOD EARTH GROUND

PLACE THIS PROBE

ON EACH EXPOSED

METAL PART

AC VOLTMETER

(HAVING 1000

/V,

OR MORE SENSITIVITY)

No. 52021

AV-14F13

AV-14F33

FEATURES

New chassis design enables use of a main board with simplified

circuitry.

Provided with miniature tuner (TV/CATV).

PLL synthesizer system TV/CATV totaling 181 channels.

Multifunctional remote control permits picture adjustment.

Adoption of the VIDEO STATUS function.

Adoption of the ON/OFF TIMER function.

With 75V/U in common (F-Type) ANT Terminal.

SLEEP TIMER for setting in real time.

Wide range voltage (110V240V) AC power input.

With AUDIO / VIDEO INPUT & OUTPUT terminal.

Closed-caption broadcast can be viewed.

No. 52021

AV-14F13

AV-14F33

MAIN DIFFERENCE LIST

Model Name

Part Name (Item)

AV-14F13/PH

AV-14F33/PH

MAIN PWB

SGA-1066A

SGA-1065A

FRONT CABINET

LC-10831-028A-H

LC-10831-027A-H

TERMINAL SHEET

GG40021-002A-H

GG40021-001A-H

SPEAKER

CEBSS09D-05KJ2

CEBSS09D-03KJ2

PACKING CASE

GG10056-079A-H

GG10056-077A-H

REMOTE CONTROL UNIT

RM-C372GY-1H

RM-C373GY-1H

Color / Sound System

NTSC / PAL-M / PAL-N

BTSC(Multi Channel Sound)

Power Consumption

42W

44W

Speaker

5cm×12cm Oval type×2 (monaural)

5×12cm Oval type×2 (stereo)

Audio Power Output

2W (monaural)

1.5W+1.5W (stereo)