background image
No.52029
Jul. 2002
AV-14A3
AV-1415EE
AV-14AMG3
1
COPYRIGHT © 2002 VICTOR COMPANY OF JAPAN, LTD.
AV-14A3 / AV-14A3/AU
AV-14A3/HK / AV-1415EE
AV-14AMG3 / AV-14AMG3/-A
CONTENTS
! SPECIFICATIONS
2
! SAFETY PRECAUTIONS
3
!
FEATURES
4
!
FUNCTIONS
5
! MAIN DIFFERENCE LIST
7
!
SPECIFIC SERVICE INSTRUCTIONS
8
! SERVICE ADJUSTMENTS
15
! PARTS LIST
33
OPERATING INSTRUCTIONS
STANDARD CIRCUIT DIAGRAM
2-1
SERVICE MANUAL
COLOUR TELEVISION
BASIC CHASSIS
CG


background image
No. 52029
AV-14A3
AV-1415EE
AV-14AMG3
2
SPECIFICATIONS
CONT ENT
ITEM
AV-14A3 / AV-14A3 /AU
AV-14A3/HK / AV-1415EE
AV-14AMG3 / AV-14AMG3/-A
Dimensions(W×H×D)
Mass
364mm×333.5mm×374mm
9.3kg
TV RF System
B/G, I, D/K
B/G, I, D/K,M
RF Mode
PAL / SECAM
PAL / SECAM / NTSC3.58 / NTSC4.43
Colour System
VIDEO Mode
PAL / SECAM / NTSC3.58 / NTSC4.43
Picture Tube
Visible size: 34cm measured diagonally
High Voltage
22.5kV±1.5kV(at zero beam current)
Receiving Frequency VHF (VL)
46.25MHz168.25MHz
VHF (VH)
175.25MHz463.25MHz
UHF
471.25MHz863.25MHz
CATV
Cable TVs of Mid (X-Z, S1-S10)
Super (S11-S20) & Hyper (S21-S41)
bands receivable
VIF Carrier
38.0MHz
Intermediate
Frequency
SIF Carrier
32.5MHz(5.5MHz)
31.5MHz (6.5MHz)
32.0MHz (6.0MHz)
32.5MHz(5.5MHz) / 33.5MHz(4.5MHz)
31.5MHz (6.5MHz)
32.0MHz (6.0MHz)
Colour Sub Carrier Frequency
PAL (4.43MHz),
SECAM (4.40625MHz / 4.25MHz)
NTSC (3.58MHz / 4.43MHz)
Power Input
Rated Voltage
[AV-14A3 / AV-1415EE]
: AC110240V, 50 / 60Hz
[AV-14A3/AU / AV-14A3/HK]
: AC220240V, 50 / 60Hz
AC110240V, 50 / 60Hz
Power Consumption
68W (Max) / 47W(Avg.)
Speaker
8cm, Round type×1
Audio Output
2W (monaural)
Aerial Input Terminal
75 Unbalanced
Input
Video
1V(p-p), 75, RCA×2 (Front / Rear)
Audio
500mV(rms) (-4dBs), High impedance,
RCA×2 (Front / Rear)
Output
Video
1V(p-p), 75, RCA×1
Audio
500mV(rms) (-4dBs), Low impedance,
RCA×1
Headphone jack
3.5mm mini jack
Remote Control Unit
RM-C360GY
(Battery size : AA / R06 / UM-3×2)
Design and specifications are subject to change without notice.


background image
No.52029
AV-14A3
AV-1415EE
AV-14AMG3
3
SAFETY PRECAUTIONS
1. The design of this product contains special hardware, many
circuits and components specially for safety purposes. For
continued protection, no changes should be made to the original
design unless authorized in writing by the manufacturer.
Replacement parts must be identic al to thos e used in the original
circuits. Service should be performed by qualified pers onnel
only.
2. Alterations of the design or circuitry of the products should not be
made. Any design alterations or additions will void the
manufacturer's warranty and will further relieve the manufacturer
of responsibility for personal injury or property damage resulting
therefrom.
3. Many electrical and mechanical parts in the products have
special safety-related characteristics. T hese characteristics are
often not evident from visual inspection nor can the protection
afforded by them necessarily be obtained by using replacement
components rated for higher voltage, wattage, etc. Replacement
parts whic h have these special s afety characteristics are
identified in the parts list of Servic e manual. Electrical
components having su ch features are identified by shading
on the schematics and by (!
!
!
!
) on the parts list in Service
manual. The us e of a substitute replacement which does not
have the same safety characteristics as the recommended
replac ement part shown in the parts list of Service manual may
cause shock, fire, or other hazards .
4. Do n't short between the LIVE side ground and ISOL ATED
(NEUTRAL) side ground or EARTH side ground when
repairing.
Some model's power circuit is partly different in the GND. The
differenc e of the GND is shown by the LIVE : (") side GND, the
ISOLATED(NEUTRAL) : (#) side GND and EARTH : ($) side
GND. Don't short between the LIVE side GND and
ISOLATED(NEUTRAL) side GND or EARTH side GND and
never measure with a measuring apparatus (oscilloscope etc.)
the LIVE side GND and ISOLATED(NEUTRAL) side GND or
EARTH side GND at the s ame time.
If above note will not be kept, a fuse or any parts will be broken.
5. If any repair has been made to the chassis, it is recommended
that the B1 setting should be checked or adjusted (See
ADJUSTMENT OF B1 POWER SUPPLY).
6. The high voltage applied to the picture tube must conform with
that specified in Service manual. Excessive high voltage can
cause an increase in X-Ray emission, arcing and possible
component damage, therefore operation under excessive high
voltage conditions should be k ept to a minimum, or should be
prevented. If s evere arc ing occurs, remove the AC power
immediately and determine the cause by visual inspection
(incorrect installation, cracked or melted high voltage harness,
poor soldering, etc.). To maintain the proper minimum level of
soft X-Ray emission, c omponents in the high voltage circuitry
including the picture tube must be the exact replacements or
alternatives approved by the manufacturer of the c omplete
product.
7. Do not c hec k high voltage by drawing an arc. Use a high voltage
meter or a high v oltage probe with a VTVM. Discharge the
picture tube before attempting meter connection, by c onnecting
a clip lead to the ground frame and c onnecting the other end of
the lead through a 10k
2W resistor to the anode button.
8. When service is required, observe the original lead dress. Extra
prec aution should be given to assure correct lead dress in the
high voltage circuit area. W here a s hort circuit has occurred,
those components that indicate evidence of overheating should
be replaced. Always use the manufacturer's replacement
components.
9. Isolation Check
(Safety for Electrical Shock Hazard)
After re-ass embling the product, always perform an isolation
check on the exposed metal parts of the cabinet (antenna
terminals, video/audio input and output terminals, Control knobs,
metal cabinet, screwheads, earphone jack, control shafts, etc.)
to be sure the product is s afe to operate without danger of
electrical shoc k.
(1) Dielectric Strength Test
The isolation between the AC primary circuit and all metal parts
exposed to the us er, particularly any expos ed metal part having a
return path to the chass is should withs tand a voltage of 3000V
AC (r.m.s.) for a period of one sec ond.
(. . . . Withstand a voltage of 1100V AC (r.m.s.) to an applianc e
rated up to 120V, and 3000V AC (r.m.s.) to an appliance rated
200V or more, for a period of one second.)
This method of test requires a test equipment not generally found
in the servic e trade.
(2) Leakage Current Check
Plug the AC line c ord directly into the AC outlet (do not use a line
isolation transformer during this check.). Using a " Leakage
Current Tester", measure the leakage current from each exposed
metal part of the cabinet, particularly any expos ed metal part
having a return path to the chassis , to a known good earth
ground (water pipe, etc.). Any leakage current must not exceed
0.5mA AC (r.m.s.).
However, in tropic al area, this must not exceed 0.2mA AC
(r.m.s.).
"
"
"
"
Alternate Check Method
Plug the AC line c ord directly into the AC outlet (do not use a line
isolation transformer during this check.). Use an AC voltmeter
having 1000 ohms per volt or more sens itivity in the following
manner. Connec t a 1500
10W res istor paralleled by a 0.15µF
AC-type c apacitor between an exposed metal part and a known
good earth ground (water pipe, etc.). Meas ure the AC voltage
across the res istor with the AC voltmeter. Move the resistor
connec tion to each exposed metal part, particularly any exposed
metal part having a return path to the chassis, and measure the
AC voltage ac ross the res istor. Now, reverse the plug in the AC
outlet and repeat eac h measurement. Any voltage measured
must not exc eed 0.75V AC (r.m.s.). This c orresponds to 0.5mA
AC (r.m.s.).
However, in tropical area, this must not exceed 0.3V AC ( r.m.s.).
This corresponds to 0.2mA AC (r.m.s.).
0.15F AC-TYPE
1500
10W
GOOD EARTH GROUND
PLACE THIS PROBE
ON EACH EXPOSED
METAL PART
AC VOLTMETER
(HAVING 1000
/V,
OR MOR E SENSITIVITY)


background image
No. 52029
AV-14A3
AV-1415EE
AV-14AMG3
4
FEATURES
" New chassis design enables us e of an interactive on-screen c ontrol.
" Wide range voltage (110V240V) AC power input (AV-14A3 / AV-1415EE / AV-14AMG3 / AV-14AMG3/-A)
"
With AUDIO / VIDEO INPUT & OUTPUT terminal.
" MUTING button can reduce the audio level to zero instantly.
"
Functional remote control to operate T V set (for channel select, volume c ontrol, power ON/OFF, etc.) from a distanc e.
" I2C bus control utilizes single chip ICs for IF, V/C, DEF. VSM PRESET, PRESET & SETUP TOUR.
"
By means of AUTO PROGRAM, the TV s tations c an be s elected automatically and the TV channels can also be rearranged automatically.
"
Built-in ON TIMER, RETURN + & CHILD LOCK.
SYSTEM BLOCK DIAGRAM
IC301
VIDEO/CHROMA
DECORDER
IC702
MEMORY
TU001
TUNER
IC701
MICRO
COMPUTER
SCL 1/SDA1
SCL 2/SDA2


background image
No. 52029
AV-14A3
AV-1415EE
AV-14AMG3
5
FUNCTIONS
FRONT PANEL
REAR TERMINAL
MENU buttons
CHANNEL / buttons
VOLUME / buttons
REMOTE CONTROL s ensor
POWER / ON TIMER lamp
MAIN POWER button
A/V INPUT terminal
HEADPHONE jack
1
2
3
4
5
6
7
8
1
2
3
4
5
6
7
8
ANT Terminal
VIDEO INPUT Terminal
AUDIO INPUT T erminal
AUDIO OUTPUT Terminal
VIDEO OUTPUT Terminal
1
2
3
4
5
2
3
4
5
1