- 1 -
PU-1569A-C
PU-1582A-C/A-D
Published by Service Dept.
Printed in Japan
Model
Service Manual
Clarion Co., Ltd.
Export Division - 22-3, Shibuya 2-chome, Shibuyaku, Tokyo, 150 Japan
Tel: 03-3400-1121
Service Dept.- 50 kamitoda,Toda-shi,Saitama,335 Japan Tel: 048-443-1111
FAX:048-433-6996
298-5603-00 Jul.1997 P
VOLKS WAGEN
Automobile Genuine
AM/FM Radio Cassette Stereo
PU-1569A-C
Genuine No. 1CO 035 180
Illumination
Red
PU-1582A-C
Genuine No. 1JO 035 180A
Illumination
Red
PU-1582A-D
Genuine No. 1JO 035 180
Illumination
Green
SPECIFICATIONS
Radio section
Tuning system:
PLL Frequency synthesizer system
Receive range:
AM 530kHz to 1,710kHz
FM 87.9MHz to 107.9MHz
Intermediate frequency:
AM 450kHz
FM 10.7MHz
Quieting sensitivity: AM Less than 38dB
(at 26dB S/N)
FM Less than 10dB
(at 30dB S/N)
Separation:
FM More than 26dB
Auto tuning stop sensitivity:
AM 42
3dB
FM 23
3dB
Tape section
Reproducting system:
4 track 2 program
2 channel stereo system
Wow and flutter:
Less than 0.3
(W.R.M.S)
Separation:
More than 40dB
Cross talk:
More than 40dB
S/N ratio:
Normal tape(120
s)
More than 48dB(DOLBY B NR OFF)
More than 56dB(DOLBY B NR ON)
Metal tape(70
s)
More than 50dB(DOLBY B NR OFF)
More than 58dB(DOLBY B NR ON)
FF/REW time:
120sec.(C-60)
(
)
(
)
Model
Model
(
)
PU-1569A
PU-1582A
General
Output power:
40W
4(MAX)
Power supply voltage:
DC13.2V(10.8V to 15.6V)
Negative ground
Consumptive current:
Less than 10A(MAX)
Dimensions(mm):
179(W)
50(H)
159(D)
Weight:
1.3kg
Dolby noise reduction manufactured under license
from Dolby Laboratories Licensing Corporation.
"DOLBY" and the double-D symbol are trademarks
of Dolby Laboratories Licensing Corporation.
Specifications and design are subject to change with-
out notice for further improvement.
COMPONENTS
PU-1569A-C/PU-1582A-C/PU-1582A-D
Main unit
1
- 2 -
PU-1569A-C
PU-1582A-C/A-D
To engineers in charge of repair
or inspection of our products.
Before repair or inspection,make sure to fol-
low the instructions so that customers and
Engineers in charge of repair or inspection can
avoid suffering any risk or injury.
1. Use specified parts.
The system uses parts with special safety features
against fire and voltage.Use only parts with equiva-
lent characteristics when replacing them.
The use of unspecified parts shall be regarded as re-
modeling for which we shall not be liable.The onus of
product liability (PL) shall not be our responsibility in
cases where an accident or failure is as a result of
unspecified parts being used.
2. Place the parts and wiring back in their original posi-
tions after replacement or re-wiring.
For proper circuit construction,use of insulation
tubes,bonding,gaps to PWB,etc,is involved.The wir-
ing connection and routing to the PWB are specially
planned using clamps to keep away from heated and
high voltage parts.Ensure that they are placed back
in their original positions after repair or inspection.
If extended damage is caused due to negligence dur-
ing repair,the legal responsibility shall be with the re-
pairing company.
3. Check for safety after repair.
Check that the screws,parts and wires are put back
securely in their original position after repair.Ensure
for safety reasons there is no possibility of secondary
ploblems around the repaired spots.
If extended damage is caused due to negligence of
repair,the legal responsibility shall be with the repair-
ing company.
4. Caution in removal and making wiring connection to
the parts for the automobile.
Disconnect the battery terminal after turning the igni-
tion key off.If wrong wiring connections are made with
the battery connected, a short circuit and/or fire may
occur.If extensive damage is caused due to negligence
of repair,the legal responsibility shall be with the re-
pairing company.
5. Cautions regarding chips.
Do not reuse removed chips even when no abnormal-
ity is observed in their appearance.Always replace
them with new ones.(The chip parts include
resistors,capacitors,diodes,transistors,etc).The nega-
tive pole of tantalum capacitors is highly susceptible
to heat,so use special care when replacing them and
check the operation afterwards.
6. Cautions in handling flexible PWB
Before working with a soldering iron,make sure that
the iron tip temperature is around 270
.Take care
not to apply the iron tip repeatedly(more than three
times)to the same patterns.Also take care not to ap-
ply the tip with force.
7. Turn the unit OFF during disassembly and parts
replacement.Recheck all work before you apply power
to the unit.
COMPUTER ANTI-THEFT SYSTEM
This unit has a built-in Computer Anti-Theft
System(CATS) whitch makes the radio inoperative if
power to the unit is interrupted for any reason
whatsoever(including disconnection and reconnection of
the car battery).The radio will remain inoperative unless
you enter the correct CATS code number.
Release CATS
1. Press the power button to turn on the power.
("SAFE"appears on the display,and "1000" appears
3 seconds later.)
2. Press 1,2,3 or 4 button the number of times neces-
sary for the secret number(CATS code) and display
the code number.
3. Press the "MANUAL UP" or "SEEK UP" button more
than 2 seconds.
If the input code number is correct,the radio turn on.A
radio frequency appears on the display.
4. If the input code number is incorrect,"SAFE" flashes
on the display,and "1000" re-appears 3 seconds
later.Input the correct code number.and press the
"MANUAL UP" or "SEEK UP" button more than 2
seconds.
ADJUSTMENTS
If you input an incorrect code number two times in
succession,it becomes impossible to input the code
for one hour.Wait one hour with the power on("SAFE"
remains on the display).After one hour,"1000" re-ap-
pears on the display.and input the correct code num-
ber.
Limiter
FM SD
AM SD
Dolby level
1. Input a 98.1MHz/65dB
(1kHz 30
MOD) signal.
2. Set an output level to 0dB(=775mV) with main volume.
3. Adjust VR102 so that the output is
3
1dB when SSG output is set 7dB
.
1. Connect TP101(
5V) to TP100(RF-MUTE).
2. Input a 107.9MHz/21dB
(1kHz 30
MOD) signal.
3. Adjust VR101 so that an output of TP102 is just hight level.
1. Connect TP101(
5V) to TP100(RF-MUTE).
2. Input a 1000kHz/42dB
(1kHz 30
MOD) signal.
3. Adjust VR100 so that an output of TP103 is just hight level.
1. Insert a Dolby level test tape(400Hz,200nWb/m).
2. Adjust VR600(L)/VR601(R) so that an output of TP600(L)/TP601(R) is
388mV
1dB.
SSG
Milli volt meter
SSG
Oscilloscope
SSG
Oscilloscope
Dolby level tape
Milli volt meter
Item
Procedure
Measuring
instrument
