CLARION PN-2669M-A - Service Manual Immediate Download

PN-2669M

- 1 -

Service Manual

Published by Service Dept.

Printed in Japan

Clarion Co., Ltd.

50 Kamitoda, Toda-shi, Saitama 335-8511 Japan

Service Dept.: 5-66 Azuma , Kitamoto-shi, Saitama 364-0007 Japan

Tel: +81-48-541-2335 / 2432 FAX: +81-48-541-2703

298-6391-00 Nov.2006

Model

( PN-2669M-A )

Model

NISSAN Automobile Genuine

CD AM/FM Radio

PN-2669M-A

(Genuine No. 28185 ET001)

(With satellite control)

PN-2669M-B

(Genuine No. 28185 ET002)

(Without satellite control)

SPECIFICATIONS

Radio section

Tuning system:

PLL frequency synthesizer system

Receive range:

87.75MHz to 107.9MHz

530kHz to 1,710kHz

Intermediate frequency:

10.7MHz

1st 10.7Mz

2nd 450kHz

Quieting sensitivity:

Less than 15dBu

(at 30dB S/N)

Less than 37dBu

(at 20dB S/N)

Separation:

30dB(1kHz)

S/N ratio:

More than 50dB

More than 40dB

Auto tuning stop sensitivity:

32dBu +6/-6dBu

39dBu +6/-6dBu

CD player section

Disc:

12cm, 8cm Disc

Separation:

More than 50dB

(1kHz,20kHz L.P.F.)

S/N ratio:

More than 65dB

(1kHz, 20kHz L.P.F., JIS-A)

Distortion:

Less than 0.4%

(1kHz, 20kHz L.P.F.)

General

Load impedance:

2 ohm/4ch

Power output:

40W x 4

Power supply voltage: DC13.2V (10.8V to 15.6V)

Negative ground

Back-up consumption: Less than 1.5mA

Dimensions(mm):

182(W) x 104(H) x 151(D)

Weight:

Approx. 1.6kg

NOTES

The tuner of this unit is DSP type. When you exchange

the tuner pack(880-2094A), it is necessary to adjust for

S-meter etc. The special JIG is used for an accurate

adjustment.

We cannot supply PWB with component parts in prin-

ciple. When a circuit on PWB has failure, please repair it

by component parts base. Parts which are not mentioned

in service manual are not supplied.

Specifications and design are subject to change without

notice for further improvement.

COMPONENT

PN-2669M-A, M-B

Main unit

-----------

PN-2669M

- 2 -

CAUTIONS

Use of controls, adjustment, or performance of procedures

other than those specified herein, may result in hazardous

radiation exposure.

The compact disc player should not be adjusted or repaired

by anyone except properly qualified service personnel.

To engineers in charge of repair or

inspection of our products.

Before repair or inspection, make sure to follow the

instructions so that customers and Engineers in charge

of repair or inspection can avoid suffering any risk or

injury.

1. Use specified parts.

The system uses parts with special safety features against fire

and voltage. Use only parts with equivalent characteristics

when replacing them.

The use of unspecified parts shall be regarded as remodeling

for which we shall not be liable. The onus of product liability

(PL) shall not be our responsibility in cases where an accident

or failure is as a result of unspecified parts being used.

2. Place the parts and wiring back in their original positions after

replacement or re-wiring.

For proper circuit construction, use of insulation tubes, bond-

ing, gaps to PWB, etc, is involved. The wiring connection and

routing to the PWB are specially planned using clamps to keep

away from heated and high voltage parts. Ensure that they are

placed back in their original positions after repair or inspec-

tion.

If extended damage is caused due to negligence during re-

pair, the legal responsibility shall be with the repairing com-

pany.

3. Check for safety after repair.

Check that the screws, parts and wires are put back securely

in their original position after repair. Ensure for safety reasons

there is no possibility of secondary ploblems around the re-

paired spots.

If extended damage is caused due to negligence of repair, the

legal responsibility shall be with the repairing company.

4. Caution in removal and making wiring connection to the parts

for the automobile.

Disconnect the battery terminal after turning the ignition key

off. If wrong wiring connections are made with the battery con-

nected, a short circuit and/or fire may occur. If extensive dam-

age is caused due to negligence of repair, the legal responsi-

bility shall be with the repairing company.

5. Cautions in soldering

Please do not spread liquid flux in soldering.

Please do not wash the soldering point after soldering.

6. Cautions in soldering for chip capacitors

Please solder the chip capacitors after pre-heating for replace-

ment because they are very weak to heat.

Please do not heat the chip capacitors with a soldering iron

directly.

7. Cautions in handling for chip parts.

Do not reuse removed chips even when no abnormality is ob-

served in their appearance. Always replace them with new

ones. (The chip parts include resistors, capacitors, diodes, tran-

sistors, etc).

Please make an operation test after replacement.

8. Cautions in handling flexible PWB

Before working with a soldering iron, make sure that the iron

tip temperature is around 270

. Take care not to apply the

iron tip repeatedly(more than three times)to the same patterns.

Also take care not to apply the tip with force.

9. Turn the unit OFF during disassembly and parts replacement.

Recheck all work before you apply power to the unit.

10. Cautions in checking that the optical pickup lights up.

The laser is focused on the disc reflection surface through the

lens of the optical pickup. When checking that the laser opti-

cal diode lights up, keep your eyes more than 30cms away

from the lens. Prolonged viewing of the laser within 30cms

may damage your eyesight.

11. Cautions in handling the optical pickup

The laser diode of the optical pickup can be damaged by elec-

trostatic charge caused by your clothes and body. Make sure

to avoid electrostatic charges on your clothes or body, or dis-

charge static electricity before handling the optical pickup.

11-1. Laser diode

The laser diode terminals are shorted for transportation in or-

der to prevent electrostatic damage. After replacement, open

the shorted circuit. When removing the pickup from the mecha-

nism, short the terminals by soldering them to prevent this

damage.

11-2. Actuator

The actuator has a powerful magnetic circuit. If a magnetic

material is put close to it. Its characteristics will change. En-

sure that no foreign substances enter through the ventilation

slots in the cover.

11-3. Cleaning the lens

Dust on the optical lens affects performance.

To clean the lens, apply a small amount of isopropyl alcohol to

lens paper and wipe the lens gently.

Top view of the unit

PN-2669M

- 3 -

ADJUSTMENT

Clock accuracy

adjustment

1. Set a universal timer to TP401(T-BASE), and adjust TC401 so that a reading of

the meter is 0+0.1/-0 sec./day.

Universal timer

EXPLANATION OF IC

051-6360-30

SAA7706H N20 Car radio Digital Signal Processor

Terminal Description

1: VDACP

: positive reference voltage ADC1, ADC2,

ADC3 and level-ADC

2: VDACN1

: ground reference voltage ADC1

3: LEVEL

: LEVEL input pin; via this pin the level of the

FM signal or level of the AM signal is fed

to the DSP1; the level information is used in

the DSP1 for dynamic signal processing

4: NAV_GND

: common mode reference input pin of the

navigation signal (pin AM_L/NAV)

5: POM

: power-on mute of the QFSDAC; timing is

determined by an external capacitor

6: RRV

: rear; right audio output of the QFSDAC

7: AUX_L

: left channel of analog AUX input

8: AUX_R

: right channel of analog AUX input

9: RLV

: rear; left audio output of the QFSDAC

pin 10: VSS A2

: ground supply analog part of the QFSDAC

and SPDIF bitslicer

pin 11: VDD A2

: positive supply analog part of the QFSDAC

and SPDIF bitslicer

pin 12: VREFDA

: voltage reference of the analog part of QFS-

DAC

pin 13: FRV

: front; right audio output of the QFSDAC

pin 14: CD_R_GND

: common-mode reference input pin for analog

CD_R or TAPE_R in the event of separated

ground reference pins for left and right are

used

pin 15: DSP2_INOUT2 : flag input/output 2 of the DSP2-core (DSP2-

flag) I2C-bus configurable

pin 16: FLV

: front; left audio voltage output of the QFS-

DAC

pin 17: DSP2_INOUT1 : flag input/output 1 of the DSP2-core (DSP2-

flag) I2C-bus configurable

pin 18: DSP2_INOUT3 : flag input/output 3 of the DSP2-core (DSP2-

flag) I2C-bus configurable

pin 19: DSP2_INOUT4 : flag input/output 4 of the DSP2-core (DSP2-

flag) I2C-bus configurable

pin 20: LOOPO

: SYSCLK output (256fs)

pin 21: TP1

: for test purpose only; this pin may be left

open or connected to ground

pin 22: VDD D3V7

: positive supply (peripheral cells only)

pin 23: VSS D3V7

: ground supply (peripheral cells only)

pin 24: SPDIF2

: SPDIF input 2; can be selected instead of

SPDIF1 via I2C-bus bit

pin 25: SPDIF1

: SPDIF input 1; can be selected instead of

SPDIF2 via I2C-bus bit

pin 26: SYSFS

: system fs clock input

pin 27: CD_WS

: digital CD-source word select input; I2S-bus

or LSB-justified format

pin 28: CD_DATA

: digital CD-source left-right data input; I2S-

bus or LSB-justified format

pin 29: CD_CLK

: digital CD-source clock input I2S-bus or

LSB-justified format

pin 30: IIS_CLK

: clock output for external I2S-bus receiver; for

example headphone or subwoofer

pin 31: IIS_IN1

: data 1 input for external I2S-bus transmitter;

e.g. audio co-processor

pin 32: IIS_IN2

: data 2 input for external I2S-bus transmitter;

e.g. audio co-processor

pin 33: IIS_WS

: word select output for external I2S-bus re-

ceiver; for example headphone or subwoof-

pin 34: IIS_OUT1

: data 1 output for external I2S-bus receiver

or co-processor

pin 35: IIS_OUT2

: data 2 output for external I2S-bus receiver or

co-processor

pin 36: VDD D3V6

: positive supply (peripheral cells only)

pin 37: VSS D3V6

: ground supply (peripheral cells only)

pin 38: DSP1_IN1

: flag input 1 of the DSP1-core

pin 39: DSP1_IN2

: flag input 2 of the DSP1-core

pin 40: DSP1_OUT1

: flag output 1 of the DSP1-core

pin 41: DSP1_OUT2

: flag output 2 of the DSP1-core

pin 42: DSP_RESET

: general reset of chip (active LOW)

pin 43: RTCB

: asynchronous reset test control block; con-

nect to ground (internal pull-down)

pin 44: SHTCB

: shift clock test control block (internal pull-

down)

pin 45: TSCAN

: scan control active high (internal pull-down)

pin 46: VDD D3V5

: positive supply (peripheral cells only)

pin 47: VSS D3V5

: ground supply (peripheral cells only)

pin 48: VDD D3V1

: positive supply (core only)

pin 49: VSS D3V1

: ground supply (core only)

pin 50: VSS D3V2

: ground supply (core only)

pin 51: VDD D3V2

: positive supply (core only)

pin 52: VDD D3V3

: positive supply (core only)

pin 53: VSS D3V3

: ground supply (core only)

pin 54: VSS D3V4

: ground supply (core only)

pin 55: VDD D3V4

: positive supply (core only)

pin 56: A0

: slave sub-address I2C-bus selection or seri-

al data input test control block

pin 57: SCL

: serial clock input I2C-bus

pin 58: SDA

: serial data input/output I2C-bus

pin 59: RDS_CLOCK

: radio data system bit clock output or RDS

external clock input I2C-bus bit controlled

pin 60: RDS_DATA

: radio data system data output

pin 61: SEL_FR

: AD input selection switch to enable high

ohmic FM_MPX input at fast tuner search on

FM_RDS input

pin 62: VSS (OSC)

: ground supply (crystal oscillator only)

pin 63: OSC_IN

: crystal oscillator input

pin 64: OSC_OUT

: crystal oscillator output

pin 65: VDD (OSC)

: positive supply (crystal oscillator only)

pin 66: AM_FM R

: right channel AM/FM input; analog input pin

pin 67: AM_FM L

: left channel AM/FM input; analog input pin

pin 68: CD_R

: right channel of analog CD input

pin 69: CD_L

: left channel of analog CD input

pin 70: DVD_R

: right channel of analog DVD input

pin 71: PHONE

: common mode PHONE signal, analog input

pin 72: DVD_L

: left channel of analog DVD input

pin 73: PHONE_GND

: common mode reference input pin of the

PHONE signal

pin 74: VDD A1

: positive supply analog (ADC1, ADC2, ADC3

and level-ADC only)

pin 75: VSS A1

: ground supply analog (ADC3 and level-ADC

only)

pin 76: VDACN2

: ground reference voltage (ADC2)

pin 77: DVD_GND

: common mode reference input pin for ana-

log DVD in the event of separated ground

reference pins used for DVD

pin 78: VREFAD

: common mode reference voltage ADC1,

ADC2, ADC3 and level-ADC

pin 79: FM_RDS

: FM RDS signal; analog input pin

pin 80: FM_MPX

: FM multiplex signal; analog input pin

Item

Procedure

Measuring instrument

PN-2669M

- 4 -

052-3208-00

M30843MW-M08GP

Audio CPU

Terminal Description

1: AF MUTE

: O : Audio frequency signal muting.

2: ILL PULSE

: IN : Illumination control signal input.

3: EEP SD

:I/O: Serial data input/output for EEP-ROM.

4: EEP CK

: O : EEP-ROM clock pulse out.

5: BU DET

: IN : Backup detection signal input.

6: BYTE

: IN : Data length selection(8bit/16bit).

7: CN VSS

: IN : Connect to VSS via a resistor.

8: ILL ON

: IN : Illumination ON signal input.

9: SYS ON

: O : System ON signal output.

pin 10: RESET

: IN : Reset signal input.

pin 11: X out

: O : Crystal connection.

pin 12: GND

: - : Ground.

pin 13: X in

: IN : Crystal connection.

pin 14: VDD

: - : Positive voltage supply.

pin 15: NMI

: IN : Nonmaskable interrupt. Connect to VDD

via a resistor.

pin 16: ACC DET

: IN : ACC detection signal input.

pin 17: PLL DI

: IN : PLL serial data input.

pin 18: PLL DO

: O : PLL serial data output.

pin 19: TIME BASE

: IN : Time base pulse input.

pin 20: V-CAN RS

: O : V-CAN standby output.

pin 21: V-CAN RX

: IN : V-CAN serial data input.

pin 22: V-CAN TX

: O : V-CAN serial data output.

pin 23: P-IC STANDBY : O : Power IC Standby signal output.

pin 24: BEEP

: O : Beep out.

pin 25: NU

: - : Not in use.

pin 26: DIMMER

: O : PWM output.

pin 27: TUNER CK

: IN : Clock pulse input from the tuner pack.

pin 28: TUNER SD

:I/O: Serial data input/output to the tuner pack.

pin 29: NDS TX

: O : NDS serial data output to NDS-A/C.

pin 30: NDS RX

: IN : NDS serial data input from NDS-A/C.

pin 31: NDS REQ

: IN : The request pulse from NDS.

pin 32: NU

: - : Not in use.

pin 33: GS1 BUCK

: O : 1CD BUCK.

pin 34: GS1 CCE

: O : 1CD CCE.

pin 35: NU

: - : Not in use.

pin 36: NU

: - : Not in use.

pin 37: GS1 BUS

:I/O: 1CD

BUS

pin 38: GS1 BUS

:I/O: 1CD

BUS

pin 39: GS1 BUS

:I/O: 1CD

BUS

pin 40: GS1 BUS

:I/O: 1CD

BUS

pin 41: GS1 RESET

: O : 1CD Reset output.

pin 42: GS1 S STOP

: IN : 1CD S STOP.

pin 43: GS1 CHU SW

: IN : 1CD CHU SW.

pin 44: GS1 TR A

: IN : 1CD TR A.

pin 45: GS1 TR B

: IN : 1CD TR B.

pin 46: GS1 LD CONT : O : 1CD LD CONT.

pin 47: GS1 LD MUTE : O : 1CD LD MUTE.

pin 48: CD ON

: O : CD ON signal output.

pin 49: PWER DIAG

: IN : The diagnosis signal input for the power

IC.

pin 50: AM ON

: O : AM ON signal output.

pin 51: KEY STANDBY : O : Standby pulse output for the key scan IC.

pin 52: KEY CHIP SEL : O : Chip select signal output to the key scan

IC.

pin 53: COMMON CK

: IN : CCB Common clock.

pin 54: COMMON DO

: O : CCB Common data.

pin 55: KEY DI

: IN : Serial data input from the Key scan IC.

pin 56: VOL 2

: IN : Volume control pulse input from the rota-

ry encoder.

pin 57: VOL 1

: IN : Volume control pulse input from the rota-

ry encoder.

pin 58: NU

: - : Not in use.

pin 59: NU

: - : Not in use.

pin 60: VDD

: - : Positive voltage supply.

pin 61: POWER ON

: IN : Power ON signal input.

pin 62: GND

: - : Ground.

pin 63: NU

: - : Not in use.

pin 64: Mini Jack Det

: IN : Mini Jack connection detection.

pin 65: DISP C/D

: O : Display C/D output.

pin 66: DISP SI

: IN : Display serial data input.

pin 67: DISP SHT

: O : Display SHT output.

pin 68: DISP SO

: O : Display serial data output.

pin 69: DISP RESET

: O : Display reset signal output.

pin 70: DISP CS

: O : Display CS output.

pin 71: GS1 SBSY

: IN : 1CD sub code block synchronous signal

intput.

pin 72: DISP KEY REQ : IN : Display key request input.

pin 73: RDS CK

: IN : RDS clock pulse input.

pin 74: RDS DI

: IN : RDS data input.

pin 75: PLL CE

: O : PLL chip enable signal output.

pin 76: PLL CK

: O : PLL clock pulse output.

pin 77: NU

: - : Not in use.

pin 78: DSP RESET

: O : Reset signal output to the DSP IC.

pin 79: S METER

: IN : Input terminal of internal A/D converter to

monitor radio field strength.

pin 80: NU

: - : Not in use.

pin 81: NU

: - : Not in use.

pin 82: CLIP DET

: IN : Clipping detection for the audio power

amplifier.

pin 83: Power ON Mute : O : DSP power-on-mute output.

pin 84: FM ON

: O : FM ON signal output.

pin 85: TEMP

: IN : Input of the internal ADC for the temper-

ature sensor.

pin 86: TEL ON

: IN : Telephone ON signal input.

pin 87: NU

: - : Not in use.

pin 88: CD EJECT

: IN : CD eject switch signal input.

pin 89: NU

: - : Not in use.

pin 90: NU

: - : Not in use.

pin 91: NU

: - : Not in use.

pin 92: N REMO B

: IN : Steering wheel remote control signal input.

pin 93: N REMO A

: IN : Steering wheel remote control signal input.

pin 94: A GND

: - : Analog ground.

pin 95: ILL DC

: IN : The illumination voltage input.

pin 96: VREFI

: IN : Reference voltage input.

pin 97: A VCC

: - : Positive voltage supply for the internal

analog section.

pin 98: DSP PIC SCL

: O : I2C clock pulse output to the DSP and the

power IC.

pin 99: DSP/P-IC DO

: O : DSP/Power-IC serial data output.

pin100: ANT ON

: O : Antenna ON command output.

PN-2669M

- 5 -

BLOCK DIAGRAM

SUB

MAIN

AM/FM-TUNER

POWER-IC

40W

RESET

ANT101

BL101

GND

EEPROM

STBY

BEEP

BACK

ACC

GND

SHIELD

GND

REQ

(CD

COMBI)

(CD

COMBI)

(COMBI

CD)

ANT-ON

STRG

ILL-

ILL+

SHIELD

STRG

GND

IC503

IC501

20K-LPF

PRE-AMP

IC301

DSP

N-BUS

AUDIO-IN

IC201

N-BUS

INTERFACE

TEL-IN+

J201(TEL/V-CAN)

TEL-IN-

TEL-ON

V-CAN+

TEL

SHIELD

V-CAN

SHIELD

V-CAN-

LED

GND

LED+

LED

GND

SO(SERIAL

OUTPUT)

RESET

SHT(SHIFT

CLOCK)

SI(SERIAL

OUTPUT)

C/D(COMMAND/DATA)

VDD+

GND

AUX

MIN

JACK

KEY-IC

IC601

MAIN

VOL

CD-EJ

MUTE

ILL

J204(DISPLAY)

IC403

AUDIO-CPU

IC402

IC405

ANT-ON

PLL-IC

IC401

SYS+5V

ILL

CONT.

LIGHT+B

BACK

REMOTE

CONT.

POWER-SUPPLY

DIMMER

D-OUT

FM/AM

TEL

AUX

N-BUS

INPUT(-)

J820(N-BUS)

N-BUS

INPUT(+)

N-BUS

INPUT(-)

N-BUS

INPUT(+)

N-BUS

DISP

KEY-

MATRIX

LH(+)

J502(POWER/SP)

LH(-)

LH(+)

LH(-)

RH(+)

RH(-)

RH(+)

RH(-)

CAN-

TRANCEVER

IC404

TEMP

TEMP+

TEMP-

For

PN-2669M-A

1CD

MECHANISM

CLIP

DET