Operation Guide ANALOG (HK-W)
1
MA0801-EA
[Modules 1362, 1398, 1770, 2799, 3378, 4370]
To set the time
Pull out the crown. Set the hands by
rotating the crown. Push the crown
back in on a time signal to resume
timekeeping.
I For watch with the elapsed time bezel
Rotate the elapsed time bezel to align the
mark with the minute hand.
After certain amount of time elapsed, read the
graduation on the elapsed time bezel which
the minute hand points to.
The elapsed time is indicated.
· Some water resistant models are equipped
with a screw lock crown.
· With such models, you must unscrew the
crown in the direction noted in the illustration
to loosen it before you can pull it out. Do not
pull too forcibly on such crowns.
· Also note that such watches are not water
resistant while their crowns are loosened. Be
sure to screw the crowns back in as far as
they will go after making any setting.
5
0
40
30
20
10
Elapsed time bezel
Crown
[Days of the Week]
English
Spanish
SUN
DOM
MON
LUN
TUE
MAR
WED
MIER
THU
JUEV
FRI
VIER
SAT
SAB
SUN 30
Crown
(Normal position)
First click
(Day, day of week setting)
Second click
(Time setting)
First click
(Day setting)
Second click
(Time setting)
Crown
(Normal position)
[Modules 1782,
4328, 4747]
· Your watch may differ somewhat from the one shown in the illustration.
[Modules 705, 706, 1300, 1311, 1330,
1344, 1360, 1399, 1747, 1771, 4394, 5049]
To set the time
1. When the second hand is at
12 o'clock, pull out the crown
to stop it.
2. Set the hands by rotating the
crown. Move the minute hand
four or five minutes past the
setting you want, and then
back them up to the setting.
3. Push the crown back in on a
time signal to resume
timekeeping.
[Modules 707, 708, 1331, 1332, 1342, 1345,
1346, 1787, 2717, 2718, 2719, 2725, 2731,
2748, 2749, 2783, 2784, 3363, 3711, 3712,
4393, 5025, 5044]
To set the time
1. When the second hand is at
12 o'clock, pull out the crown to the
second click to stop it.
2. Set the hands by rotating the crown.
Move the minute hand four or five
minutes past the setting you want,
and then back them up to the setting.
3. Push the crown back in on a time
signal to resume timekeeping.
To set the day
· Avoid setting the day between 8:00
p.m. and 2:00 a.m. The day may not
change in the following day if you do.
1. Pull out the crown to the first click.
2. Set the day by rotating the crown.
3. Push the crown back in to its normal
position.
[Modules 709, 1333, 1347, 3716]
To set the time
1. When the second hand is at
12 o'clock, pull out the crown to the
second click to stop it.
2. Set the hands by rotating the crown.
Move the minute hand four or five
minutes past the setting you want,
and then back them up to the
setting.
3. Push the crown back in on a time
signal to resume timekeeping.
To set the day and day of the
week
· Avoid setting the day and day of the
week between 8:00 p.m. and 4:00
a.m. The day and day of the week
may not change in the following day if
you do.
1. Pull out the crown to the first click.
2. Set the day by rotating the crown
counterclockwise.
3. Set the day of the week by rotating
the crown clockwise. Confirm that
the correct language (English or
Spanish) is selected.
4. Push the crown back in to its normal
position.
[Module 4746]
30
Crown
(Normal position)
First click (Day setting)
Crown