CASIO MTG700-2DR - Owner's Manual Immediate Download

USER'S GUIDE 2549

About This Manual

· Button operations are indicated using the letters shown

in the illustration.

· Each section of this manual provides you with the

information you need to perform operations in each

mode. Further details and technical information can be

found in the "Reference" section.

(Light)

General Guide

· Press C to change from mode to mode.

· In any mode, press L to illuminate the display.

Timekeeping

Use the Timekeeping Mode to set and view the current

time and date.

Read This Before You Set the Time and Date !

The times displayed in the Timekeeping Mode and World

Time Mode are linked. Because of this, make sure you

select a city code for your Home City (the city where you

normally use the watch) before you set the time and date.

Timekeeping Mode

World Time Mode

e-DATA MEMORY Mode

Stopwatch Mode

Countdown Timer Mode

Alarm Mode

Press

Seconds

Hour : Minutes

indicator

Day of week

Month Day

To set the time and date

1. In the Timekeeping Mode, hold down A until the

seconds start to flash, which indicates the setting

screen.

2. Press C to move the flashing in the sequence shown

below to select other settings.

City code

Minutes

12/24-Hour

Format

Seconds

City Code

Hour

Year

Day

DST

Month

3. When the setting you want to change is flashing, use D and B to change it as

described below.

· For full information on city codes, see the "City Code Table".

· See "Daylight Saving Time (DST)" for details about DST setting.

4. Press A to exit the setting screen.

· With the 12-hour format, the P (PM) indicator appears on the display for times in the

range of noon to 11:59 p.m. and the A (AM) indicator appears for times in the range

of midnight to 11:59 a.m.

· With the 24-hour format, times are displayed in the range of 0:00 to 23:59, without

any indicator.

· The 12-hour/24-hour timekeeping format you select in the Timekeeping Mode is

applied in all modes.

· The day of the week is automatically displayed in accordance with the date (year,

month, and day) settings.

Daylight Saving Time (DST)

Daylight Saving Time (summer time) advances the time setting by one hour from Standard

Time. Remember that not all countries or even local areas use Daylight Saving Time.

To toggle the Timekeeping Mode time between DST and Standard Time

1. In the Timekeeping Mode, hold down A until the

seconds start to flash, which indicates the setting

screen.

2. Press C to display the DST setting screen.

3. Press D to toggle between Daylight Saving Time

(ON displayed) and Standard Time (OFF displayed).

· Note that you cannot switch between Standard Time

and Daylight Saving Time while GMT is selected as

the Home City code.

4. Press A to exit the setting screen.

· The DST indicator appears on the display to indicate

that Daylight Saving Time is turned on.

Screen

DSTOFF

TYO

10:58

12H

2002

6-30

To do this:

Reset the seconds to 00

Toggle between Daylight Saving Time (0N)

and Standard Time (0FF)

Change the city code

Change the hour or minutes

Toggle between 12-hour (12H) and 24-hour

(24H) timekeeping

Change the year

Change the month or day

Do this:

Press D.

Use D (east) and B (west).

Use D (+) and B ().

Press D.

Use D (+) and B ().

e-DATA MEMORY

You can use the watch's e-DATA MEMORY to store e-mail

addresses, Web page URLs, and other text data.

You can also use a password to limit access to e-DATA

MEMORY contents.

· All of the operations in this section are performed in the

e-DATA MEMORY Mode, which you enter by pressing

e-DATA MEMORY Management

e-DATA MEMORY can hold up to 315 characters total,

while each record can contain up to 63 characters. The

maximum number of records depends on the number of

characters per record, as shown below.

· 63 characters per record: 5 records

· 7 or fewer characters per record: 40 records

To create a new e-DATA MEMORY record

1. In the e-DATA MEMORY Mode, press D and B at the

same time to display the remaining memory screen.

· If 0 % is shown for remaining memory, it means that

memory is full. To store another record, you will first

have to delete some of the records stored in memory.

2. Hold down A until the flashing cursor ( #) appears on

the display, which indicates the setting screen.

· The setting screen also shows the record number that

is automatically assigned to the new record.

3. Input the text you want.

· When inputting the text, use D (+) and B () to

cycle through characters at the current cursor

location, and C to move the cursor to the right. See

"Inputting Text".

Record number

(Page number)

Text

Remaining memory (%)

4. Press A to store your data and return to the e-DATA MEMORY record screen

(without the cursor).

· Pressing A causes the message SET to appear for about two seconds as the data

is stored. After that, the e-DATA MEMORY record screen appears.

· The text can show only three characters at a time, so longer text scrolls continuously

from right to left. The last character is indicated by the symbol s after it. Press A to

stop and restart scrolling.

· Records are stored in memory in the sequence they are created.

To recall e-DATA MEMORY records

In the e-DATA MEMORY Mode, use D (+) and B () to cycle through e-DATA

MEMORY records as shown below.

Press

Remaining

memory

screen

Record 1

()

Record 2

()

Password

setting

screen

Remaining Memory Screen

Password Setting Screen

· The value on the remaining memory screen is the percentage of memory that is still

available. It does not indicate the number of records that can be stored.

· The Password Setting screen shows

xxxx when a password is already registered.

· You can use the Password Setting screen to register, edit, or delete your password.

See "Using a Password to Protect e-DATA MEMORY Data" for more information.

To edit an e-DATA MEMORY record

1. In the e-DATA MEMORY Mode, use D (+) and B () to display the record you

want to edit.

2. Hold down A until the flashing cursor appears on the display.

3. Use C to move the flashing to the character you want to change.

4. Use D (+) and B () to change the character.

5. After making the changes you want, press A to store them and return to the

e-DATA MEMORY record screen.

USER'S GUIDE 2549

To delete an e-DATA MEMORY record

1. In the e-DATA MEMORY Mode, use D (+) and B () to display the record you

want to delete.

2. Hold down A until the flashing cursor appears on the display.

3. Press B and D at the same time to delete the record.

· The message CLR appears to indicate that the record is being deleted. After the

record is deleted, the cursor appears on the display, ready for input.

4. Input data or press A to return to the remaining memory screen.

Using a Password to Protect e-DATA MEMORY Data

You can register a 4-digit password to keep e-DATA MEMORY data secure.

Important!

Use a 4-digit password that is easy for you to remember, but difficult for others to

decipher. If you forget the password, you will have to have your watch initialized

(which deletes all data in memory) in order to access the e-DATA MEMORY again. To

have the watch initialized, contact the store or dealer where you purchased it, and ask

to have the AC operation performed.

To register a new password

1. In the e-DATA MEMORY Mode, use D (+) and B ()

to display the Password Setting screen.

· This displays a screen that shows SET PA55.

2. Hold down A for about one second until NEW

appears, with the first 0 flashing.

· This is the New Password Setting screen.

3. Use D (+) and B () to scroll through numbers at the first digit.

4. When the first digit is the number you want, press C to advance to the next digit.

5. Repeat steps 3 and 4 to input all four digits of the password you want.

· Pressing A while inputting a new password clears your input and returns to the

Password Setting screen.

6. After all four of the password digits are the way you want, press C to register

them.

· Pressing C causes the message SET to appear for about one second as the

password is stored. After that, the Password Setting screen appears.

· After registering a password, you can input, recall, edit and delete data, if you want.

After you exit the e-DATA MEMORY Mode, you will have to input the password

every time you want to enter it again.

To input the password

1. Enter the e-DATA MEMORY Mode.

2. On the Password Input screen (PA55 xxxx), press D

or B. This causes the first digit of the password to

flash.

3. Input the password.

· Use D (+) and B () to scroll through numbers at

each digit.

· Press C to advance to the next digit.

· Pressing A while inputting the password clears your

input and returns to the Password Input screen.

4. After the password is the way you want, press C.

· If the input password matches the one registered, the message OK!appears,

followed by an e-DATA MEMORY screen.

· If the password does not match, the message ERR appears, followed by the

Password Input screen.

To change the password

1. Enter the e-DATA MEMORY Mode by inputting the current password.

2. Use D (+) and B () to display the Password Setting screen.

3. Perform the procedure starting from step 2 under "To register a new password" to

specify the new password.

To delete the password

1. Enter the e-DATA MEMORY Mode by inputting the current password.

2. Use D (+) and B () to display the Password Setting screen.

3. Hold down A for about one second until NEW appears, with the first 0 flashing.

4. Press B and D at the same time to delete the password.

· The message CLR appears to indicate that the password is being deleted. After the

password is deleted, the Password Setting screen appears.

World Time

World Time shows the current time in 27 cities (29 time

zones) around the world.

· All of the operations in this section are performed in the

World Time Mode, which you enter by pressing C.

To view the time in another city code

In the World Time Mode, press D to scroll through city

codes (time zones) to the east or B to scroll to the west.

· For full information about city codes, see the "City Code

Table".

· If the current time shown for a city is wrong, check your

Timekeeping Mode time and Home City code settings

and make the necessary changes.

· When the currently selected time zone is one that includes

mostly ocean, a value indicating the zone's Greenwich

Mean Time differential appears in place of a city code.

To toggle a city code time between Standard Time and Daylight Saving Time

1. In the World Time Mode, use B and D to display the

city code (time zone) whose Standard Time/Daylight

Saving Time setting you want to change.

2. Hold down A for about one second to toggle Daylight

Saving Time (DST displayed) and Standard Time (DST

not displayed).

· The DST indicator is on the display whenever you

display a city code for which Daylight Saving Time is

turned on.

· Note that the DST/Standard Time setting affects only the currently displayed city

code. Other city codes are not affected.

· Note that you cannot switch between Standard Time and Daylight Saving Time while

GMT

is selected as the city code.

Current time in the zone

of the selected city code

Timekeeping

Mode time

City code

Alarms

You can set up to five independent multi-function alarms

with hour, minutes, month, and day. When an alarm is

turned on, the alarm tone sounds when the alarm time is

reached. One of the alarms is a snooze alarm, while the

other four are one-time alarms. You can also input

reminder text that appears when the alarm time is

reached.

You can also turn on an Hourly Time Signal that causes

the watch to beep twice every hour on the hour.

· There are five alarm screens numbered AL1through

AL4

for the one-time alarm, a snooze alarm screen

indicated by SNZ. The Hourly Time Signal screen is

indicated by SIG.

· The alarm number indicator points to the number of the

alarm screen that is currently displayed. In the case of

the snooze alarm screen, the snooze alarm indicator

(

) appears in the lower right corner of the display.

· Alarm settings (and Hourly Time Signal settings) are available in the Alarm Mode,

which you enter by pressing C.

Alarm Types

The alarm type is determined by the settings you make, as described below.

· Daily alarm

Set the hour and minutes for the alarm time. This type of setting causes the alarm to

sound everyday at the time you set.

· Date alarm

Set the month, day, hour and minutes for the alarm time. This type of setting causes

the alarm to sound at the specific time, on the specific date you set.

· 1-Month alarm

Set the month, hour and minutes for the alarm time. This type of setting causes the

alarm to sound everyday at the time you set, only during the month you set.

· Monthly alarm

Set the day, hour and minutes for the alarm time. This type of setting causes the alarm

to sound every month at the time you set, on the day you set.

To set an alarm time

1. In the Alarm Mode, use D and B to scroll through the

alarm screens until the one whose time you want to set

is displayed.

Press

· To set a one-time alarm, display one of the screens indicated by an alarm number

from AL1through AL4. To set the snooze alarm, display the screen indicated

by SNZ.

· The snooze alarm repeats every five minutes.

2. After you select an alarm, hold down A until the hour setting of the alarm time

starts to flash, which indicates the setting screen.

· This operation automatically turns on the alarm.

3. Press C to move the flashing in the sequence shown below to select other settings.

Hour

Text

Minutes

Month

Day

· Selecting the text causes the text input cursor ( #) to appear. There are eight

spaces in the text, so you have to press C eight times to move to the Hour

setting.

4. While a setting is flashing, use D, B, and C to change it as described below.

Alarm time

(Hour : Minutes)

Alarm number

indicator

Alarm number

Timekeeping Mode time

· Pressing B and D at the same time while any setting is flashing automatically

sets the time to AM12:00 and the date to x-xx. It also clears any text that is input

for the alarm.

5. Press A to exit the setting screen.

· If you input reminder text, the text appears in place of

the alarm number. When this happens, you can find out

which alarm's screen is displayed by checking the alarm

number indicator or the snooze alarm indicator.

· If the reminder text is more than three characters, it will

scroll form right to left.

· If the alarm has a month and/or day setting, the month/

day appears in the upper right corner of the display, in

place of the Timekeeping Mode time.

Screen

12:00

x-xx

To do this:

Change the hour

and minutes

Change the

month and day

Input reminder

text

Do this:

Use D (+) and B ().

·With the 12-hour format, set the time correctly as a.m.

(A indicator) or p.m. (P indicator).

·To set an alarm that does not include a month and/or

day, set x for each setting.

Use D (+) and B () to cycle through characters at the

current cursor location, and C to move the cursor to the

right. See "Inputting Text".

Snooze alarm indicator

Alarm on indicator

Alarm Operation

The alarm tone sounds at the preset time for 10 seconds, regardless of the mode the

watch is in. In the case of the snooze alarm, the alarm operation is performed a total

of seven times, every five minutes, until you turn the alarm off.

· To stop the alarm tone after it starts to sound, press any button.

· If you input reminder text for an alarm, the text appears for one minute on the

Timekeeping Mode screen when the alarm time is reached. You can clear the

reminder text display by pressing A, B, or D, or by exiting the Timekeeping

Mode.

· In the case of the snooze alarm, the reminder text appears on the Timekeeping

Mode screen for the initial alarm operation only.

· Performing any one of the following operations during a 5-minute interval between

snooze alarms cancels the current snooze alarm operation.

Displaying the Timekeeping Mode setting screen

Displaying the SNZ setting screen

Changing the DST setting of the Home City code in the World Time Mode

To test the alarm

In the Alarm Mode, hold down D to sound the alarm.

USER'S GUIDE 2549

To turn an alarm on and off

1. In the Alarm Mode, use D and B to select an alarm.

2. Press A to toggle it on and off.

· Turning on a alarm (AL1to AL4, or SNZ) displays

the alarm on indicator (

) on its Alarm Mode screen.

· In all modes, the alarm on indicator is shown for any

alarm that is currently turned on.

· The alarm on indicator and applicable alarm number

indicator flash while the alarm is sounding.

· The snooze alarm indicator (

) flashes during the

5-minute intervals between alarms.

· In other modes besides the Alarm Mode, alarm number

indicators are displayed for each alarm that is currently

turned on.

To turn the Hourly Time Signal on and off

1. In the Alarm Mode, use D and B to select the Hourly

Time Signal (SIG).

2. Press A to toggle it on (ON) and off (OFF).

· The Hourly Time Signal on indicator (

) is shown on

the display in all modes while this function is turned on.

Alarm number indicator

(Alarm 3)

Alarm on indicator

Hourly time signal on

indicator

Countdown Timer

You can set the countdown timer within a range of

one minute to 24 hours. An alarm sounds when the

countdown reaches zero.

· You can also select auto-repeat, which automatically

restarts the countdown from the original value you set

whenever zero is reached.

· The initial default countdown start time when you

purchase the watch or after you have its battery

replaced is 15 minutes.

· Countdown timer functions are available in the

Countdown Timer Mode, which you can enter using C.

Hours

Minutes

Seconds

Timekeeping Mode time

To use the countdown timer

Press D while in the Countdown Timer Mode to start the countdown timer.

· When the end of the countdown is reached and auto-repeat is turned off, the alarm

sounds for 10 seconds or until you stop it by pressing any button. The countdown

time is automatically reset to its starting value after the alarm stops.

· When the end of the countdown is reached and auto-repeat is turned on, the alarm

sounds, but the countdown starts again automatically whenever the countdown

reaches zero.

· The countdown timer measurement operation continues even if you exit the

Countdown Timer Mode.

· Press D while a countdown operation is in progress to pause it. Press D again to

resume the countdown.

· To completely stop a countdown operation, first pause it (by pressing D), and then

press B. This returns the countdown time to its starting value.

To set up the countdown timer

1. While the countdown start time is on the display in the

Countdown Timer Mode, hold down A until the hour

setting of the countdown start time starts to flash, which

indicates the setting screen.

· If the countdown start time is not displayed, use the

procedure "To use the countdown timer" to display it.

2. Press C to move the flashing in the sequence shown

below to select other settings.

Auto-repeat

Minutes

Hours

3. While a setting is flashing, use D and B to change it as described below.

· To specify a countdown start time of 24 hours, set 0:00.

4. Press A to exit the setting screen.

· The auto-repeat on indicator (

) appears on the display while this function is turned on.

· Frequent use of auto-repeat and the alarm can run down battery power.

Stopwatch

The stopwatch lets you measure elapsed time, split times,

and two finishes.

· The display range of the stopwatch is 23 hours,

59 minutes, 59.99 seconds.

· The stopwatch continues to run, restarting from zero

after it reaches its limit, until you stop it.

· The stopwatch measurement operation continues even

if you exit the Stopwatch Mode.

· Exiting the Stopwatch Mode while a split time is frozen

on the display clears the split time and returns to

elapsed time measurement.

· All of the operations in this section are performed in the

Stopwatch Mode, which you enter by pressing C.

Screen

0:15

RPTOFF

To do this:

Change the hours or minutes

Toggle auto-repeat on (ON) and off (OFF)

Do this:

Use D (+) and B ().

Press D.

To measure times with the stopwatch

Elapsed Time

Start

Stop

Re-start

Stop

Clear

Start

Split

(

displayed)

Split release

Stop

Clear

Start

Split

Stop

Split release

Clear

Split Time

Two Finishes

First runner

finishes.

Display time of

first runner.

Second runner

finishes.

Display time of

second runner.

· The time on the screen may not appear to stop immediately when you press a

button to stop timing or to perform a split operation. Despite this, the time recorded

by your button operation is accurate.

Backlight

The backlight uses an EL (electro-luminescent) panel that

causes the entire display to glow for easy reading in the

dark. The watch's auto light switch automatically turns on

the backlight when you angle the watch towards your

face.

· The auto light switch must be turned on (indicated by

the auto light switch on indicator) for it to operate.

· See "Backlight Precautions" for other important

information about using the backlight.

To turn on the backlight manually

In any mode, press L to illuminate the display for about

one second.

· The above operation turns on the backlight regardless

of the current auto light switch setting.

About the Auto Light Switch

Turning on the auto light switch causes the backlight to turn on for about one second,

whenever you position your wrist as described below in any mode.

Moving the watch to a position that is parallel to the ground and then tilting it

towards you more than 40 degrees causes the backlight to turn on.

Parallel to ground

More than 40 °

Warning!

· Always make sure you are in a safe place whenever you are reading the

display of the watch using the auto light switch. Be especially careful when

running or engaged in any other activity that can result in accident or injury.

Also take care that sudden illumination by the auto light switch does not

surprise or distract others around you.

· When you are wearing the watch, make sure that its auto light switch is turned

off before riding on a bicycle or operating a motorcycle or any other motor

vehicle. Sudden and unintended operation of the auto light switch can create

a distraction, which can result in a traffic accident and serious personal injury.

To turn the auto light switch on and off

In the Timekeeping Mode, hold down L for about one second to toggle the auto light

switch on (

displayed) and off (

not displayed).

· The auto light switch on indicator (

) is on the display in all modes while the auto

light switch is turned on.

· In order to protect against running down the battery, the auto light switch

automatically turns off approximately six hours after you turn it on. Repeat the above

procedure to turn the auto light switch back on if you want.

Reference

This section contains more detailed and technical information about watch operation.

It also contains important precautions and notes about the various features and

functions of this watch.

Inputting Text

The following describes how to input text in the e-DATA MEMORY and Alarm Modes.

To input characters

1. When the cursor is on the display, use D and B to

cycle through the available letters, numbers and

symbols, in the sequence shown below.

Hours

Seconds

1/100 second

Minutes

Auto light switch on

indicator

Cursor

(space)

(symbol)

(number)

Press

(lower-case)

(upper-case)

2. When the character you want is at the cursor position, press C to move the cursor

to the right.

3. Repeat steps 1 and 2 to input the rest of the characters you want.

· See the "Character List" for information about the characters you can input.

USER'S GUIDE 2549

Auto Return Features

· If you leave the watch in the e-DATA MEMORY or Alarm Mode for two or three

minutes without performing any operation, it automatically changes to the

Timekeeping Mode.

· If you leave a screen with flashing digits or a cursor on the display for two or three

minutes without performing any operation, the watch automatically saves any

settings you have made up to that point and exits the setting screen.

Scrolling

The B and D buttons are used in various modes and setting screens to scroll

through data on the display. In most cases, holding down these buttons during a scroll

operation scrolls at high speed.

Initial Screens

When you enter the e-DATA MEMORY, World Time, or Alarm Mode, the data you

were viewing when you last exited the mode appears first.

Timekeeping

· Resetting the seconds to 00 while the current count is in the range of 30 to 59

causes the minutes to be increased by 1. In the range of 00 to 29, the seconds are

reset to 00 without changing the minutes.

· The year can be set in the range of 2000 to 2039.

· The watch's built-in full automatic calendar makes allowances for different month

lengths and leap years. Once you set the date, there should be no reason to change

it except after you have the watch's battery replaced.

World Time

· The current time in all World Time Mode cities is calculated in accordance with the

Greenwich Mean Time (GMT) differential for each city, based on the current Home

City time setting in the Timekeeping Mode.

· The seconds count of the World Time is synchronized with the seconds count of the

Timekeeping Mode.

· The GMT differential is the time difference of the time zone where the city is located

from Greenwich Mean Time.

· GMT differential is calculated by this watch based on Universal Time Coordinated

(UTC) data.

Backlight Precautions

· The electro-luminescent panel that provides illumination loses power after very long

use.

· The illumination provided by the backlight may be hard to see when viewed under

direct sunlight.

· The watch may emit an audible sound whenever the display is illuminated. This is

due to vibration of the EL panel used for illumination, and does not indicate

malfunction.

· The backlight automatically turns off whenever an alarm sounds.

· Frequent use of the backlight shortens the battery life.

Auto light switch precautions

· Wearing the watch on the inside of your wrist and movement or vibration of your

arm can cause the auto light switch to activate and illuminate the display. To avoid

running down the battery, turn off the auto light switch whenever engaging in

activities that might cause frequent illumination of the display.

· The backlight may not light if the face of the watch is

more than 15 degrees above or below parallel. Make

sure that the back of your hand is parallel to the ground.

· The backlight turns off in about one second, even if you

keep the watch pointed towards your face.

· Static electricity or magnetic force can interfere with

proper operation of the auto light switch. If the backlight

does not light, try moving the watch back to the starting

position (parallel with the ground) and then tilt it back

toward you again. If this does not work, drop your arm

all the way down so it hangs at your side, and then bring

it back up again.

· Under certain conditions, the backlight may not light

until about one second after you turn the face of the

watch towards you. This does not necessarily indicate

malfunction of the backlight.

Character List

More than 15 degrees

too high

City Code Table

*Based on data as of June 2002.

PAGO PAGO

HNL

HONOLULU

PAPEETE

ANC

ANCHORAGE

NOME

LAX

LOS ANGELES

SAN FRANCISCO, LAS VEGAS, VANCOUVER, SEATTLE,

DAWSON CITY

DEN

DENVER

EL PASO, EDMONTON

CHI

CHICAGO

HOUSTON, DALLAS/FORT WORTH, NEW ORLEANS,

MEXICO CITY, WINNIPEG

NYC

NEW YORK

MONTREAL, DETROIT, MIAMI, BOSTON, PANAMA CITY,

HAVANA, LIMA, BOGOTA

CCS

CARACAS

LA PAZ, SANTIAGO, PORT OF SPAIN

RIO

RIO DE JANEIRO

SAO PAULO, BUENOS AIRES, BRASILIA, MONTEVIDEO

PRAIA

GMT

+00

DUBLIN, LISBON, CASABLANCA, DAKAR, ABIDJAN

LON

LONDON

PAR

PARIS

+01

MILAN, ROME, MADRID, AMSTERDAM, ALGIERS,

HAMBURG, FRANKFURT, VIENNA, STOCKHOLM, BERLIN

CAI

CAIRO

+02

ATHENS, HELSINKI, ISTANBUL, BEIRUT, DAMASCUS,

JRS

JERUSALEM

CAPE TOWN

JED

JEDDAH

+03

KUWAIT, RIYADH, ADEN, ADDIS ABABA, NAIROBI, MOSCOW

THR

TEHRAN

+3.5

SHIRAZ

DXB

DUBAI

+04

ABU DHABI, MUSCAT

KBL

KABUL

+4.5

KHI

KARACHI

+05

MALE

DEL

DELHI

+5.5

MUMBAI, KOLKATA

DAC

DHAKA

+06

COLOMBO

RGN

YANGON

+6.5

BKK

BANGKOK

+07

JAKARTA, PHNOM PENH, HANOI, VIENTIANE

HKG

HONG KONG

+08

SINGAPORE, KUALA LUMPUR, BEIJING, TAIPEI, MANILA,

PERTH, ULAANBAATAR

TYO

TOKYO

+09

SEOUL, PYONGYANG

ADL

ADELAIDE

+9.5

DARWIN

SYD

SYDNEY

+10

MELBOURNE, GUAM, RABAUL

NOU

NOUMEA

+11

PORT VILA

WLG WELLINGTON

+12

CHRISTCHURCH, NADI, NAURU ISLAND

City

GMT

Other major cities in same time zone

Code

Differential