CASIO MTG530SC-2B - Owner's Manual Immediate Download

Module No. 2339

2339-1

WORLD TIME MODE

The World Time Mode shows you the current time in 27

cities (29 time zones) around the world.

· For full information on city codes, see the "CITY CODE

TABLE".

· The time setting of the Timekeeping Mode and the World

Time Mode are synchronized. Whenever you change

the time setting for any city in the Timekeeping Mode,

the settings of all World Time cities are changed ac-

cordingly.

To select a World Time City and view its time

1. In the World Time Mode, press D to scroll forward

through the city codes (time zones). Holding down D

scrolls at high speed.

2. When the city code you want is on the display, press

A to view its current time.

· The backlight may not illuminate if the face of the watch is more than 15 degrees off

parallel to the left or right. Make sure that the back of your hand is parallel to the

ground.

TIMEKEEPING MODE

· Press D to toggle the display between the date screen

(day of the week, month, day) and the time screen (hour,

minutes, seconds).

To set the time and date

1. While in the Timekeeping Mode, hold down A until the

seconds digits flash on the display, indicating the set-

ting screen.

2. Press C to move the flashing in the sequence shown

below.

3.While the seconds setting is selected (flashing), press

D to reset it to 00. If you press D while the seconds

setting is in the range of 30 to 59, the seconds are re-

set to 00 and 1 is added to the minutes. If the seconds

setting is in the range of 00 to 29, the minutes count is

unchanged.

· Static electricity or magnetic force can interfere with proper operation of the auto

backlight function. If the auto backlight does not illuminate, try moving the watch

back to the starting position (parallel with the ground) and then tilt it back toward

you again. If this does not work, drop your arm all the way down so it hangs at your

side, and then bring it back up again.

· Under certain conditions the backlight may not light until about one second or less

after turning the face of the watch towards you. This does not necessarily indicate

malfunction of the backlight.

To switch the auto light switch function on and off

In the Timekeeping Mode, hold down D for one or two seconds to turn the auto light

switch function on and off.

· The auto light switch indicator is shown on the display in all modes while the auto

light switch function is on.

· In order to protect against running down the battery, the auto light switch function is

automatically turned off approximately six hours after you turn it on. Repeat the

above procedure to turn the auto light switch function back on if you want.

· Pressing B at any time illuminates the display, regardless of the auto light switch's

on/off setting.

Caution

· The backlight of this watch employs an electro-luminescent (EL) light, which loses

its illuminating power after very long term use.

· Frequent use of the backlight shortens the battery life.

· The watch emits an audible sound whenever the display is illuminated. This is be-

cause the EL light vibrates slightly when lit. It does not indicate malfunction of the

watch.

Warning!

· Never try to read your watch when mountain climbing or hiking in areas that

are dark or in areas with poor footing. Doing so is dangerous and can result

in serious personal injury.

· Never try to read your watch when running where there is the danger of acci-

dents, especially in locations where there might be vehicular or pedestrian

traffic. Doing so is dangerous and can result in serious personal injury.

· Never try to read your watch when riding on a bicycle or when operating a

motorcycle or any other motor vehicle. Doing so is dangerous and can result

in a traffic accident and serious personal injury.

· When you are wearing the watch, make sure that its auto light switch function

is turned off before riding on a bicycle or operating a motorcycle or any other

motor vehicle.

Sudden and unintended operation of the auto light switch can create a dis-

traction, which can result in a traffic accident and serious personal injury.

GENERAL GUIDE

· Press C to change from mode to mode.

· Pressing B in any mode illuminates the digital display for about 1.5 seconds. The backlight is disabled while a setting screen is on the display.

· If you do not perform any operation for a few minutes while a setting screen (with flashing digits) is on the display, the watch automatically exits the setting screen.

Press C.

Press

Timekeeping Mode

World Time Mode

Telememo Mode

Alarm Mode

Stopwatch Mode

Hand Setting Mode

DST

Press D.

Minute hand

Hour hand

Month-

Day

24H indicator

Hour

Minutes

Seconds

Day of

week

DST on indicator

· While the DST (Daylight Saving Time) setting is selected, press D to toggle it on

and off. If you turn the DST on, the DST on indicator appears on the display.

· The DST on/off setting you make for the city code that is currently selected in the

Timekeeping Mode (your home time city) is also applied to that city code in the

World Time Mode.

· While the city codes setting is selected, use D (+) and B () to scroll thorough the

available codes until the one you want to use as your home time city is displayed.

· For full information on city codes, see the "CITY CODE TABLE".

· While the 12/24-hour setting is selected, press D to switch between the two for-

mats.

· With 12-hour timekeeping, times between midnight and noon are indicated by A

(am), while times between noon and midnight are indicated by P (pm).

· The 24H indicator is on the display while 24-hour timekeeping is selected.

· While any other setting is selected (flashing), press D (+) or B () to change it.

Holding down either button changes the setting at high speed.

4. After you make the settings you want, press

A to exit the setting screen.

· The day of the week is automatically set in accordance with the date.

· The date can be set within the range of January 1, 2000 to December 31, 2039.

· The watch's built-in full automatic calendar automatically makes allowances for dif-

ferent month lengths and leap years. Once you set the date, there should be no

reason to change it except after the replacement of the watch's battery.

Daylight Saving Time (DST), which is also sometimes called "summer time" ad-

vances the time for one hour, as is the custom in some areas during the summer.

Remember that not all countries or even local areas use Daylight Saving Time.

Seconds

DST

City Code

Hour

Minutes

Day

Month

Year

12/24

DST

ABOUT THE BACKLIGHT

About the Auto Light Switch Function

When the auto light switch function is turned on, the backlight automatically turns on

for about 1.5 seconds under the conditions described below. Avoid wearing the watch

on the inside of your wrist. Doing so causes the auto light switch to operate when not

needed, which shortens battery life.

Moving the watch to a position that is parallel to the ground and then tilting it towards

you approximately 40 degrees causes the backlight to illuminate.

Parallel to

ground

Parallel to ground

More than 15 degrees

too high

More than 15 degrees

too low

Hold down D.

Auto light switch

indicator

OFF

Press A.

Press

Mode

indicator 2

Current Time in

City Code zone

City

Code

DST on indicator

Mode indicator 1

3. While the time screen is on the display, press D to switches back to the city code

screen.

· At this point you could press D again to scroll through city codes.

Daylight Saving Time (DST)

Daylight Saving Time automatically advances the time setting by one hour from

Standard Time. You can make individual Daylight Saving Time settings for each city

code (time zone). Remember that not all countries or even local areas use Daylight

Saving Time.

To switch between Standard Time and Daylight Saving Time

1. In the World Time Mode, use D to display the city code (time zone) whose stan-

dard time/daylight saving time setting you want to change.

2. Hold down A toggle between Daylight Saving Time and Standard Time.

· The DST indicator appears on the display whenever you display a city code for

which daylight saving time is turned on.

2339-2

TELEMEMO MODE

The Telememo Mode lets you store up to 30 records, each

with a name (up to eight characters) and a phone number

(up to 14 digits). Records are automatically sorted based

on the names. You can recall records by scrolling through

them on the display.

· See the "CHARACTER LIST" for details on how the

watch sorts records.

· The message "NO-DATA" appears when there are no

records stored in memory.

· The blank screen appears when you scroll to the loca-

tion between the last and the first records stored in

memory.

Press D.

Press A.

Mode indicator

Telephone number

Name

Remaining memory

0 ~ 9

(Space)

Press

· The record on the display when you exit the Telememo Mode appears first the next

time you enter the Telememo Mode.

To input a new Telememo record

1. In the Telememo Mode, if the message "NO-DATA" is not on the display, press D

and B at the same time. This causes the blank screen to appear.

· If the blank screen does not appear when you press D and B, it means that

memory is full. To store another record, you will first have to delete a record stored

in memory.

2. Hold down A and a cursor appears on the display.

3. Use D (+) and B () to scroll through characters at the current cursor position.

Characters scroll in the sequence shown below.

· Holding down D or B scrolls at high speed.

4. When the character you want is at the current cursor position, press C to move

the cursor to the right.

5. Repeat the steps 3 and 4 to input the rest of the characters.

6. After you input the name, use C to move the cursor to the right until the number

input screen "-----" appears.

· You can input up to eight characters for the name, though only six characters are

visible at a time. If the name you input has fewer than eight characters, use C to

move the cursor to the eighth space (which means you would press C three times

after inputting a five-character name).

· Pressing C again while the cursor is at the eighth space changes to the number

input screen. When the cursor is at the 14th digit of the number input screen, press-

ing C causes the name input screen to appear again.

7. Use D (+) and B () to scroll through characters (hyphen, numbers, space) at the

current cursor position on the number screen. Characters scroll in the sequence

shown below.

A ~ Z

0 ~ 9

(

(Space)

Press

· Holding down D or B scrolls characters at high speed.

8.When the character you want is at the cursor position, press C to move the cursor

to the right.

9.Repeat steps 7 and 8 to input the rest of the numbers you want.

· You can input up to 14 digits for the number.

10. After inputting the name and number of the record, press A to store it.

· The message "SORT" appears on the display for a few moments after you press

A to indicate that the watch is sorting records.

· After the record is sorted, the cursor appears in the display, ready for input.

11. Input the next record or press A to exit the setting screen.

· The display can show only six name characters or nine number digits at a time.

Longer names and numbers scroll continuously from right to left. The symbol "

indicates that the character or digit to the left is the last, and the character or digit to

the right is the first.

· Pressing D while a name is scrolling on the display jumps to the first character of

the name. Scrolling resumes from there.

· Pressing A while a number is scrolling on the display jumps to the first digit of the

number. Scrolling resumes from there.

To recall Telememo data

1. In the Telememo Mode, press D to scroll forward through the names of the stored

records.

· Holding down D scrolls through the names at high speed.

2. When the name for the record you want is on the display, press A to view its

number.

3. Pressing D while a number screen is on the display returns to the name screen.

· At this point you could press D again to scroll through names.

To edit Telememo data items

1. In the Telememo Mode, press D to scroll forward through the names of the stored

records.

· Holding down D scrolls through the names at high speed.

2. When the name for the record you want is on the display, hold down A until the

cursor appears in the display.

3. Use C to move the cursor to the character you want to change.

4. Use D (+) and B () to change the character.

· See step 3 of "To input a new Telememo record" for information on inputting name

characters, and step 7 for inputting number characters.

5. After making the changes that you want, press A to store them and exit the set-

ting screen.

· The message "SORT" appears on the display for a few moments after you press

A to indicate that the watch is sorting records.

To delete Telememo data

1. In the Telememo Mode, press D to scroll forward through the names of the stored

records.

· Holding down D scrolls through the names at high speed.

2. When the name for the record you want is on the display, hold down A until the

cursor appears in the display.

3. Press D and B at the same time. The message "CLEAR" appears in the display,

indicating that the record was deleted.

· After the record is deleted, the cursor appears in the display, ready for input.

4. Input a record or press A to exit the setting screen.

ALARM MODE

You can set up to five daily alarms. When the Daily Alarm

is turned on, the alarm sounds for 20 seconds at the pre-

set time each day. Press any button to stop the alarm

after it starts to sound. When the Hourly Time Signal is

turned on, the watch beeps every hour on the hour.

To set the alarm time

1. While in the Alarm Mode, press D to display the num-

ber of the alarm you want to set.

Mode indicator

Alarm number

Hour Minutes

Alarm on indicator

2. Hold down A until the hour digits flash on the display, indicating the setting screen.

· At this time, the alarm is turned on automatically.

3. Press C to move the flashing in the sequence shown below.

4. Use D (+) and B () to change the setting. Holding down either button changes

the setting at high speed.

5. After you set the alarm time, press A to exit the setting screen.

· The format (12-hour and 24-hour) of the alarm time matches the format you select

in the Timekeeping Mode.

· When setting the alarm time using the 12-hour format, take care to set the time

correctly as morning or afternoon.

To stop the alarm

· Press any button to stop the alarm after it starts to sound.

To turn a daily Alarm or the Hourly Time Signal on and off

1. Use D to display the alarm you want to turn on or off, or the screen for turning the

Hourly Time Signal on or off.

2. Press A to toggle the displayed alarm or Hourly Time Signal on and off.

· In the Alarm Mode, the alarm on indicator appears to indicate the on/off status of

the currently displayed alarm. In all other modes, the alarm on indicator appears

when any one of the five alarms is turned on. The alarm on indicator is not dis-

played in other modes when all alarms are turned off.

Alarm 1

Alarm 5

Alarm 2

Alarm 3

Alarm 4

Hourly Time Signal

Hour

Minutes

Daily Alarm indicator

Hourly Time

Signal indicator

· The Hourly Time Signal indicator is displayed in all modes when the Hourly Time

Signal is turned on.

To test the alarm

In the Alarm Mode, hold down D to sound the alarm.

· The alarm test does not work while the Alarm Mode setting screen is on the display.

· Holding down D to test the alarm also advances to the next alarm number.

Mode indicator

1/100 second

Minutes

Seconds

STOPWATCH MODE

The Stopwatch Mode lets you measure elapsed time, split

times, and two finishes. The range of the stopwatch is 59

minutes, 59.99 seconds. You can use the EL backlight by

pressing B at any time while the stopwatch is operating.

Elapsed time measurement

Start

Stop

Re-start

Stop

Clear

Split time measurement

Start

Split

Split release

Stop

Clear

Split time and 1st-2nd place times

Start

Split

Stop

Split release

Clear

First runner

finishes.

Second runner

finishes.

Record time of

first runner.

Record time of

second runner.

2339-3

HAND SETTING MODE

When the analog setting does not match the time shown

on the digital display, use this mode to correct the analog

setting.

1. Hold down A while in the Hand Setting Mode until the

message "SET" start to flash on the display.

2. Each press of D advances the hands 20 seconds. Hold-

ing down D advances the hand at high speed.

· Pressing B while holding down D causes the hand

setting to change at high speed, even if you release the

buttons. Press any key to stop.

· The analog time setting does not stop automatically when

it reaches the current time. You must stop the hands manu-

ally.

· Note that the hands can be advanced only and cannot be moved back. Take care

so you do not go past the setting you want to make.

3. After you set the analog time, press A to exit the setting screen.

· Depending on your timing when you operate the D button, the above operation

can cause the minute hand timing to become late. If this happens, repeat the above

operation to correct the minute hand timing.

Mode indicator

Hour

Minutes

CITY CODE TABLE

HNL

HONOLULU

PAPEETE

ANC

ANCHORAGE

NOME

LAX

LOS ANGELES

SAN FRANCISCO, LAS VEGAS,

VANCOUVER, SEATTLE, DAWSON CITY

DEN

DENVER

EL PASO, EDMONTON

HOUSTON, DALLAS/FORT WORTH,

CHI

CHICAGO

NEW ORLEANS, MEXICO CITY,

WINNIPEG

MONTREAL, DETROIT, MIAMI, BOSTON,

NYC

NEW YORK

PANAMA CITY, HAVANA, LIMA,

BOGOTA

CCS

CARACAS

LA PAZ, SANTIAGO, PORT OF SPAIN

RIO

RIO DE JANEIRO

SAO PAULO, BUENOS AIRES, BRASILIA,

MONTEVIDEO

GMT

LON

LONDON

DUBLIN, LISBON, CASABLANCA,

DAKAR, ABIDJAN

MILAN, ROME, MADRID, AMSTERDAM,

PAR

PARIS

ALGIERS, HAMBURG, FRANKFURT,

VIENNA, STOCKHOLM, BERLIN

CAI

CAIRO

ATHENS, HELSINKI, ISTANBUL,

JRS

JERUSALEM

BEIRUT, DAMASCUS, CAPE TOWN

JED

JEDDAH

MOSCOW, KUWAIT, RIYADH, ADEN,

ADDIS ABABA, NAIROBI

+3.5

THR

TEHRAN

SHIRAZ

DXB

DUBAI

ABU DHABI, MUSCAT

+4.5

KBL

KABUL

KHI

KARACHI

MALE

+5.5

DEL

DELHI

MUMBAI, CALCUTTA

DAC

DHAKA

COLOMBO

+6.5

RGN

YANGON

BKK

BANGKOK

JAKARTA, PHNOM PENH, HANOI,

VIENTIANE

SINGAPORE, KUALA LUMPUR,

HKG

HONG KONG

BEIJING, TAIPEI, MANILA, PERTH,

ULAANBAATAR

TYO

TOKYO

SEOUL, PYONGYANG

+9.5

ADL

ADELAIDE

DARWIN

+10

SYD

SYDNEY

MELBOURNE, GUAM, RABAUL

+11

NOU

NOUMEA

PORT VILA

+12

WLG

WELLINGTON

CHRISTCHURCH, NADI, NAURU ISLAND

Based on data as of June 2000.

GMT

City

Other major cities in same time zone

differential Code

CHARACTER LIST