CASIO MRG200T-7 - Owner's Manual Immediate Download

-- 2 --

2. OPERATION CHART: QW-1673

GENERAL GUIDE

· Press C to change from mode to mode. Each mode is explained in detail on the

following pages.

· In any mode, press E to illuminate the display for about three seconds.

Contact Code Mode

Identification (ID) Mode

Vital Statistics Mode

Timekeeping Mode

Alarm Mode

Stopwatch Mode

TIMEKEEPING MODE

In addition to normal timekeeping, the Timekeeping Mode

is also used to set the current time and date, and to turn the

EL alarm on and off.

· In the Timekeeping Mode, graphic area indicates counting

of seconds.

To set the time and date

1. Press A while in the Timekeeping Mode. The seconds

digits flash on the display because they are

selected.

2. Press C to change the selection in the following

sequence.

Seconds

Hour

Minutes

12/24-hour

format

Year

Month

Day

3. While the seconds digits are selected (flashing), press D to reset the seconds to 00.

If you press D while the seconds count is in the range of 30 to 59, the seconds are

reset to 00 and 1 is added to the minutes. If the seconds count is in the range of 00

to 29, the minutes count is unchanged.

4. While any other digits (besides seconds) are selected (flashing), press D to increase

the number. While the 12/24-hour setting is selected, press D to switch between the

two formats.

· Holding down D changes the current selection at high speed.

· When the 12-hour format is selected, the 12H indicator appears on the display. With

the 12-hour format, the P (PM) indicator appears on the display to indicate "p.m."

times. There is no indicator for "a.m." times.

· Selecting the 24-hour format causes the 24H and the 24 indicators to appear on the

display.

5. After you set the time and date, press A to return to the Timekeeping Mode.

· The day of the week is automatically set in accordance with the date.

· The date can be set within the range of January 1, 1995 to December 31, 2039.

· If you do not operate any button for a few minutes while a selection is flashing, the

flashing stops and the watch goes back to the Timekeeping Mode automatically.

About the backlight

In any mode, press E to illuminate the display for about

three seconds. If the EL alarm is turned on, the backlight

flashes whenever a daily alarm or hourly time signal sounds.

Note

· For details on using the alarm function, see "ALARM

MODE".

· The backlight of the watch employs an electro-luminescent

(EL) light, which loses illuminating power after very long

use.

· The backlight remains lit for about three seconds from the point you press E , even if

it already lit when you press E . If you keep E depressed for one or two minutes, the

backlight will automatically turn off.

· The illumination provided by the backlight may be hard to see when viewed under

direct sunlight.

· The backlight automatically stops illuminating whenever an alarm sounds.

· The watch will emit an audible sound whenever the display is illuminated. This is caused

by a transistor that vibrates when the EL panel lights up. It does not indicate malfunction

of the watch.

To turn the EL alarm on and off

In the Timekeeping Mode, hold down D for one or two seconds to turn the EL alarm on

and off.

· An EL alarm on indicator (

) appears on the display to indicate that the EL alarm is

turned on. The indicator disappears when you turn the EL alarm off.

· When an alarm is reached while the EL alarm is turned on, the flashing of the backlight

and the timing of the alarm tones may not be exactly matched. This is normal and does

not indicate malfunction.

Month Day

Year

Minutes

Seconds

PM indicator

Hour

Day of

week

Graphic area

CONTACT CODE MODE

The Contact Code Mode lets you store up to 20* sets of

contact data (such as telephone numbers). Stored data is

sorted automatically into alphabetic sequence based on the

text area text.

* The Contact Code Mode shares memory with the

Identification (ID) Mode. This means that the maximum

number of Contact Code Mode entries you can store is

reduced by one each time you store Identification Mode.

To check remaining memory

In the Contact Code Mode, hold down B and D to display

how much memory remains for input of data. The value that

appears shows how many more data items (Contact Code

Mode and ID Mode) you can input.

· This watch has three built-in ID Mode titles, which are programmed in memory when

you first purchase the watch and which are automatically set whenever the watch's

battery is replaced. Because of this, the remaining memory display shows a value of

17 (20 3) whenever it is performed immediately after you purchase the watch or

have the battery changed.

To input new Contact Code data

1. In the Contact Code Mode, press B or D until the new

data screen appears.

· If there is no Contact Code data stored in memory yet, the

new data screen appears as soon as you enter the Contact

Code Mode.

· If the message FULL appears in the text area, it means

that memory is full. To store more data, you will first have

to delete some of the data stored in memory.

2. Press A and a cursor appears in the text area.

3. Input a name in the text area and a contact number in the

number area.

· You can input up to eight characters in the text area, and 12 digits in the number area.

Use B and D to input characters, and C to move the cursor around the display.

For details, see "How to input characters".

· Make sure that you distinguish between the letter O and the number 0 (zero). Inputting

a zero for the letter O will affect automatic sorting.

4. After inputting your data, press A to store it and return to the Contact Code Mode.

· The text area can show only five characters at a time, so longer messages scroll

continuously right to left.

To recall Contact Code data

In the Contact Code Mode, press D to scroll forward through stored data items or B to

scroll in reverse.

· Holding down either button scrolls through the data at high speed.

· The data item that is displayed when you exit the Contact Code Mode is still displayed

the next time you enter the Contact Code Mode.

To edit Contact Code data items

1. In the Contact Code Mode, scroll through the data items and display the one you want

to edit.

2. Press A and a cursor appears in the text area.

3. Use C to move the cursor to the character you want to change.

4. Change the character.

· See "How to input characters" for details.

5. After making the changes that you want, press A to store them and return to the

Contact Code Mode.

To delete Contact Code data

1. In the Contact Code Mode, scroll through the data items and display the one you want

to delete.

2. Press A and a cursor appears in the text area.

3. Press B and D at the same time to delete the Contact Code data item.

· At this time the cursor appears in the text area, ready for input.

4. Input data or press A to return to the Contact Code Mode.

Number area

Text area

Mode indicator

Cursor

Text area

Number area

[New Data Screen]

EL alarm on indicator

-- 3 --

To edit ID Mode data items

1. In the ID Mode, scroll through the data items and display the one you want to edit.

2. Press A and the characters in the text area begin to flash.

· You can also use this procedure to edit built-in title names.

3. Use C to move the cursor to the character you want to change.

4. Change the character.

· See "How to input characters" for details.

5. After making the changes that you want, press A to store them and return to the ID

Mode.

To delete ID Mode data items

1. In the ID Mode, scroll through the data items and display the one you want to delete.

2. Press A and the characters in the text area begin to flash.

3. Press B and D at the same time to delete the ID data item.

4. Press A to return to the ID Mode.

VITAL STATISTICS MODE

The Vital Statistics Mode provides space in memory for storage of your name, blood

type, and the date of your birth.

To recall Vital Statistics data

In the Vital Statistics Mode, press D or B to change the data on the display in the

following sequence.

Press D

Press B

· The name display always appears first whenever you enter the Vital Statistics Mode.

Important!

· In the blood type display, the text area shows the blood type (A, B, O, AB) and

the number area indicates the Rh factor (+ or ). If no blood type data is stored in

memory (after you purchase the watch or have the battery replaced), the text

area shows "" and the number area shows "RH". Since these indicators can

easily be misunderstood as meaning "RH negative," we recommend that you

input the correct blood type data as soon as possible when necessary.

· Use the Vital Statistics Mode to store your own personal data (name, blood type, date

of birth). Once you input your personal data, take care that the watch is not borrowed

by another person. Otherwise, emergency medical personnel may assume that your

data in the Vital Statistics Mode applies to the person who borrowed the watch.

· Data stored in the Vital Statistics Mode is cleared when you have the battery of the

watch replaced. Be sure to input data again after battery replacement.

To input your name

1. In the Vital Statistics Mode, display the NAME screen.

2. Press A and a cursor appears in the text area.

3. Input your name into the text area.

· You can input up to 20 characters for your name.

Use B and D to input characters, and C to move

the cursor around the display. For details, see "How to

input characters".

· You can clear the characters currently input for the name by pressing B and D at the

same time.

4. After inputting your data, press A to store it and return to the normal NAME screen.

· The text area can show only five characters at a time, so a longer name scrolls

continuously right to left.

To input your blood type

1. In the Vital Statistics Mode, display the BLOOD screen.

2. Press A and the blood type ABO appears in the text

area.

3. Use B and

to scroll through the available blood types

in the following sequence:

Press D

Press B

4. Press C to advance to specification of the Rh factor.

· At this time the current Rh factor (xx or *) will flash on the display.

5. Press B or D to select either xx (negative) or * (positive).

6. After inputting your data, press A to store it and return to the normal BLOOD screen.

To input the date of your birth

1. In the Vital Statistics Mode, display the BIRTH screen.

2. Press A and the year digits flash in the number area

because they are

selected.

3. Press C to change the selection in the following

sequence:

Month

Year

Day

[New Data Screen]

Text area

Number area

IDENTIFICATION (ID) MODE

With the Identification (ID) Mode, you can input up to 20*

sets of data, each of which contains a title (such as passport,

credit card, etc.) and a number. Data is automatically sorted

into the alphabetic sequence of the titles.

* The ID Mode shares memory with the Contact Code Mode.

This means that the maximum number of ID Mode entries

you can store is reduced by one each time you store

Contact Code Mode.

Important!

The ID Mode is useful for storing important data like passport numbers, license numbers,

credit card numbers, etc. Note, however, that storing such important data in the watch's

memory runs the risk of it being misused should you lend the watch to someone, or should

the watch become lost or stolen. Because of this, the manufacturer strongly recommends

that you store such important information in coded form that cannot be understood by

others.

Note that CASIO COMPUTER CO., LTD. shall not be held liable to you or any third party

for any losses or damages suffered through the misuse of data stored in the memory of

this watch.

About titles

· This watch has three built-in ID Mode titles: PASSPORT, LICENSE, and

CREDIT (credit card). You can use these built-in titles as they are, append eight

more characters to a built-in title (to indicate a credit card company name, for example),

or change a built-in title to a different one.

· In addition to the three built-in titles, you can also input your own titles, up to eight

characters long.

· You can input more than one set of data using the same title.

About automatic sorting

ID Mode data items are automatically sorted according to their titles. The three built-in

titles come first, followed by the titles you input, in alphabetical order.

To check remaining memory

In the ID Mode, hold down B and D to display how much

memory remains for input of data. The value that appears

shows how many more data items (Contact Code Mode and

Identification Mode) you can input.

· This watch has three built-in ID Mode titles, which are

programmed in memory when you first purchase the watch

and which are automatically set whenever the watch's

battery is replaced. Because of this, the remaining memory

display shows a value of 17 (20 3) whenever it is

performed immediately after you purchase the watch or

have the battery changed.

To input new ID Mode data

1. In the ID Mode, press B or D until the text area of the

display shows either one of the built-in titles or the new

data screen.

· If the message FULL appears in the text area, it means

that memory is full. To store more data, you will first have

to delete some of the data already stored in memory.

2. Press A and the characters in the text area begin to

flash.

3. Use D and B to display a built-in title or new title input

(-----). Each press of B and D changes the

selected title in the following sequence.

Press D

PASSP?

(PASSPORT)

LICEN?

(LICENSE)

CREDI?

(CREDIT)

-----

Press B

· The built-in titles PASSP, LICEN, and CREDI always appear in the above

sequence, along with the display for input of a new title. Titles you previously created

when inputting other data do not appear.

· If you want to input your own title for the data, select -----.

4. Press C and a cursor appears in the text area.

5. Input a title in the text area and a number in the number area.

· You can input up to eight characters in the text area, and 12 digits in the number area.

Use B and D to input characters, and C to move the cursor around the display.

For details, see "How to input characters".

· If you are using a built-in title, you can append up to eight characters to the built-in title.

· To use a built-in title as it is without appending text, press C eight times to move the

cursor to the number area.

6. After inputting your data, press A to store it and return to the normal ID Mode data

screen.

· The text area can show only five characters at a time, so longer titles scroll continuously

right to left.

To recall ID Mode data

In the ID Mode, press D to scroll forward through stored data items or B to scroll in

reverse.

· Holding down either button scrolls through the data at high speed.

· The data item that is displayed when you exit the ID Mode is still displayed the next

time you enter the ID Mode.

Text area

Name

Date of Birth

Blood type

Number area

Cursor

Text area

Mode indicator

Number area

Blood type ABO

Rh factor

Month

Day

Year

-- 4 --

4. Press D to increase the selected digits and B to decrease them. Holding down

either button changes the selected digits at high speed.

· The year can be set in the range of 1900 to 2039.

5. After inputting your data, press A to store it and return to the normal BIRTH screen.

ALARM MODE

When the Daily Alarm is turned on, the alarm sounds for 20

seconds at the preset time each day. Press any button to

stop the alarm after it starts to sound.

When the Hourly Time Signal is turned on, the watch beeps

every hour on the hour.

To set the alarm time

1. Press A while in the Alarm Mode. The hour digits flash

on the display because they are

selected.

· This operation will turn the Daily Alarm on automatically.

2. Press C to change the selection in the following

sequence.

Hour

Minutes

3. Press D to increase the selected digits. Holding down D changes the selection at

high speed.

· The format (12-hour and 24-hour) of the alarm time matches the format you select for

normal timekeeping.

· When setting the alarm time using the 12-hour format, take care to set the time correctly

as morning (no indicator) or afternoon (P).

4. After you set the alarm time, press A to return to the Alarm Mode.

To turn the Daily Alarm and Hourly Time Signal on and off

Press D while in the Alarm Mode to change the status of the Daily Alarm and Hourly

Time Signal in the following sequence.

[Alarm ON Indicator/Hourly Time Signal ON Indicator]

To test the alarm

Hold down B while in the Alarm Mode to sound the alarm.

STOPWATCH MODE

The Stopwatch Mode lets you measure elapsed time, split

times, and two finishes. The range of the stopwatch is 23

hours, 59 minutes, 59.99 seconds.

3. Repeat steps 1 and 2 until your text is complete.

· The text area in the Contact Code Mode and ID Mode can hold up to eight characters.

When the cursor is located at the eighth space of the text area in these modes, moving

the cursor to the right causes it to jump down to the first digit in the number area. When

the cursor is at the 12th digit of the number area, moving it to the right causes it to jump

back up to the first character of the text area.

· You can input only numbers and spaces in the number area. Each press of D or B

changes the input at the current cursor location in the following sequence:

0 to 9

(space)

· If you do not perform any button operation for about two or three minutes while the

cursor is on the display, the watch automatically returns to the normal data display (the

cursor disappears).

Press D

Press B

CHARACTER LIST

Alarm on indicator

Mode indicator

Hourly time signal on

indicator

Minutes

Hour

Daily Alarm

Only

Hourly Time

Signal only

Both ON

Both OFF

First runner

finishes.

Record time of

second runner.

(a) Elapsed time measurement

Start

Stop

Re-start

Stop

Clear

(b) Split time measurement

Start

Split

Split release

Stop

Clear

Start

Split

Stop

Split release Clear

Second runner

finishes.

Record time of

first runner.

1/100 second

Hours

Seconds

Minutes

Mode indicator

Press B

Press D

Text area

INPUTTING TEXT

The following describes how to input text in the Contact Code Mode, ID Mode, and Vital

Statistics Mode.

How to input characters

1. When the cursor is blinking in the text area, use D and

B to scroll through the available letters, numbers and

symbols, in the following sequence.

A to Z

0 to 9

(Alphabet)

(Japanese)

(space)

· Holding down either button scrolls through at high speed.

· You can input Japanese characters (katakana), English alphabetic characters, numbers,

and symbols in the text area. For a complete list of characters you can input, see the

"CHARACTER LIST" at the back of this manual.

2. When the character you want at the cursor position is shown, press C to move the

cursor to the right.

Number area

Cursor

space