CASIO GW701D-8B - Owner's Manual Immediate Download

USER'S GUIDE 2534/2654

If the display of the watch is blank...

If the SLEEP indicator is on the display, it means that the

display is blank because the watch's Power Saving

function has turned off the display to conserve power.

Power Saving automatically turns off the display and puts

the watch into a sleep state whenever your watch is left for

a certain period where it is dark.

· The initial factory default setting is Power Saving on.

· The watch recovers from the sleep state if you move it to

a well-lit area*, if you press any button, or if you angle

the watch towards your face for reading.

It can take up to five seconds for the display to turn on.

· See "Power Saving Function" for more information.

Getting Acquainted

Congratulations upon your selection of this CASIO watch. To get the most out of your

purchase, be sure to carefully read this manual and keep it on hand for later reference

when necessary.

Expose the watch to bright light to charge its battery before using it.

You can use this watch even as its battery is being charged by exposure to bright

light.

· Be sure to read "Battery" of this manual for important information you need

to know when exposing the watch to bright light.

About This Manual

· Button operations are indicated using the letters shown

in the illustration.

· Each section of this manual provides you with the

information you need to perform operations in each

mode. Further details and technical information can be

found in the "Reference" section.

(Light)

MO0302-A

Telememo Mode

World Time Mode

Countdown Timer Mode

Alarm Mode

General Guide

· Press C to change from mode to mode.

· In any mode, press L to illuminate the display.

Timekeeping Mode

Press C.

Stopwatch Mode

Hour

Seconds

12/24-Hour

Format

Power Saving

Day

Month

Year

Minutes

Timekeeping

Use the Timekeeping Mode to set and view the current

time and date.

To set the time and date

1. In the Timekeeping Mode, hold down A until the

seconds start to flash, which indicates the setting

screen.

2. Press C to move the flashing in the sequence shown

below to select other settings.

Hour : Minutes Seconds

Year

Day of week

Month Day

PM indicator

3. When the setting you want to change is flashing, use D and B to change it as

described below.

4. Press A to exit the setting screen.

· See "Power Saving Function" for details about configuring Power Saving settings.

· The 12-hour/24-hour timekeeping format you select in the Timekeeping Mode is

applied in all modes.

Setting

Seconds

Hour, Minutes

12/24-Hour

Format

Year,Month,Day

Power Saving

Button Operation

Press D to reset to

00.

Use D (+) and B () to change the setting.

Press D to toggle between 12-hour (

12H) and

24-hour (

24H) timekeeping.

Use D (+) and B () to change the setting.

Press D to toggle Power Saving on (

ON) and

off (

OFF).

Screen

· The day of the week is automatically displayed in accordance with the date (year,

month, and day) settings.

To create a new Telememo record

1. In the Telememo Mode, use B and D to cycle through

the record screens until the new data screen appears.

· The new data screen is the one that is blank (contains

no name and telephone number).

· If the message FULL appears on the display, it

means that memory is full. To store another record,

you will first have to delete some of the records stored

in memory.

2. Hold down A until the flashing cursor (

_) appears in

the name area of the display.

3. In the name area, use D and B to cycle through

characters at the cursor position. The characters cycle

in the sequence shown below.

Name area

Number area

New Data Screen

A to Z

(space)

0 to 9

-.:/

Press D.

Press B.

4. When the character you want is at the cursor position, press C to move the cursor

to the right.

5. Repeat steps 3 and 4 until the name is complete.

· You can input up to eight characters for the name.

6. After you input the name, press C as many times as necessary to move the cursor

to the number area.

· When the cursor is located at the eighth space of the name area, moving the

cursor to the right causes it to jump to the first digit of the number. When the

cursor is at the 12th digit of the number, moving it to the right (by pressing C)

causes it to jump to the first character in the name.

7. In the number area, use D and B to cycle through numbers and symbols

(hyphen, space) at the cursor position. The characters cycle in the sequence shown

below.

8. When the character you want is at the cursor position, press C to move the cursor

to the right.

9. Repeat steps 7 and 8 until you complete number input.

· You can input up to 12 digits for the number.

10. After inputting your data, press A to store it.

· After data storage is complete, the cursor appears in the name area of the

display, ready for input of a new Telememo record.

11. Input more data (starting from step 3) or press A again to return to the Telememo

record screen (without the cursor).

· The name can show only three characters at a time, so longer text scrolls

continuously from right to left. The last character is indicated by the symbol

after it.

0 to 9

(space)

Press D.

Press B.

Telememo

The Telememo Mode lets you store up to 30 records, each

containing name and telephone number data. Records are

automatically sorted based on the characters of the name.

You can recall records by scrolling through them on the

display.

· See "Sort Table" for details on how the watch sorts

records.

· All of the operations in this section are performed in the

Telememo Mode, which you enter by pressing C.

Remaining memory

Name

Telephone number

USER'S GUIDE 2534/2654

Reset Time

You can set a "reset time," which is a kind of alternate countdown start time you can

recall with the press of a button any time a countdown operation is in progress.

Timer Mode

The countdown timer gives you a choice of two modes: auto-repeat and elapsed time.

Auto-repeat

Auto-repeat mode automatically restarts the countdown from the countdown start time

you set whenever zero is reached.

· Auto-repeat mode is best when timing the starts of match races.

· Even if you start a countdown operation from the reset time, the countdown

automatically restarts from the countdown start time whenever it reaches zero.

· Auto repeat timing repeats up to seven times.

To recall Telememo records

In the Telememo Mode, use D (+) and B () to scroll through Telememo records on

the display.

· Pressing D while the last Telememo record is on the display or B while the first

record is on the display displays the new data screen.

To edit a Telememo record

1. In the Telememo Mode, use D (+) and B () to scroll through the records and

display the one you want to edit.

2. Hold down A until the flashing cursor appears on the display.

3. Use C to move the flashing to the character you want to change.

4. Use D (+) and B () to change the character.

5. After making the changes that you want, press A to store them and return to the

Telememo record screen.

To delete a Telememo record

1. In the Telememo Mode, use D (+) and B () to scroll through the records and

display the one you want to delete.

2. Hold down A until the flashing cursor appears on the display.

3. Hold down D and B until the watch beeps and

CLR stops flashing on the

display.

· The message

CLR appears, which indicates that the record is being deleted.

After the record is deleted, the cursor appears on the display, ready for input.

4. Input data or press A to return to the Telememo record screen.

World Time

The World Time Mode shows you the current time in 27

cities (29 time zones) around the world.

· The time settings of the Timekeeping Mode and the

World Time Mode are independent from each other, so

you must make separate settings for each.

· Whenever you change the time setting for any city in the

World Time Mode, the settings of all other cities are

changed accordingly.

· For full information on city codes, see the "City Code

Table".

· All of the operations in this section are performed in the

World Time Mode, which you enter by pressing C.

City Code

GMT differential

Timekeeping Mode time

Current time in the zone

of the selected city code

To view the time in another city code

In the World Time Mode, press D to scroll through city codes (time zones) to the east

or B to scroll to the west.

To set the World Time

1. In the World Time Mode, use D and B to scroll

through the city code (time zone) and find the one you

want.

2. Hold down A until the hour setting of the world time

starts to flash, which indicates the setting screen.

3. Press C to move the flashing between the hour and

minute settings.

4. While a setting is flashing, use D (+) and B () to

change it.

5. Press A to exit the setting screen.

Daylight Saving Time (DST)

Daylight Saving Time (summer time) advances the time setting by one hour from

Standard Time. Remember that not all countries or even local areas use Daylight

Saving Time.

To toggle a city code time between Standard Time and Daylight Saving Time

1. In the World Time Mode, use D and B to display the

city code whose Standard Time/Daylight Saving Time

setting you want to change.

2. Hold down A until the hour setting of the world time

starts to flash, which indicates the setting screen.

3. Press L to toggle Daylight Saving Time (

displayed)

and Standard Time (

not displayed).

4. Press A to exit the setting screen.

· The Daylight Saving Time indicator appears while the

GMT differential is on the display only. It does not

appear while the city code is on the display.

· Note that you cannot switch between Standard Time

and Daylight Saving Time while

GMT is selected as the

city code.

· Note that the DST/Standard Time setting affects only the

currently displayed city code. Other city codes are not

affected.

· The indicator is on the display whenever you display a

city code for which Daylight Saving Time is turned on.

Elapsed Time

When the end of the countdown is reached in the elapsed time mode, the timer

automatically switches to an elapsed time measurement operation.

· The elapsed time mode is best when timing the speed of yachts during ocean races.

· The elapsed time operation is performed in one-second increments up to 99 hours,

59 minutes, 59 seconds.

Countdown Timer Beeper Operations

The watch beeps at various times during a countdown so you can keep informed

about the countdown status without looking at the display. The following describes the

types of beeper operations the watch performs during a countdown.

Countdown End Beeper

The watch beeps each second of the final 10 seconds before a countdown reaches

zero, and at zero. The first five beeps (seconds 10 through 6) are higher pitched than

the final five beeps (seconds 5 through 1). The watch emits a longer beep to signal

when the countdown reaches zero.

· The countdown end beeper always sounds, regardless of the on/off status of the

progress beeper.

Progress Beeper

The progress beeper actually includes two beepers: a reset time beeper and a reset

period progress beeper.

· The reset time beeper and reset period progress beeper sound only while the

progress beeper is turned on.

Reset Time Beeper

The reset time beeper is similar to the countdown end beeper. When the progress

beeper is turned on, the watch beeps each second of the final 10 seconds before the

countdown reaches the reset time.

Reset Period Progress Beeper

The reset period is the portion of the countdown between the reset time and zero.

When the progress beeper is turned on, the watch emits four short beeps at the top of

each minute during the reset period, and 30 seconds before the end of the

countdown.

Countdown Timer Examples

Countdown start time: 10 minutes; Reset time: 5 minutes; Timer mode: Auto-repeat;

Progress beeper: On

10'00"

Start Time

Reset Time

0'00"

1'00" 0'30"

2'00"

3'00"

4'00"

5'00"

Reset Period

Reset Period Progress Beeper

Countdown

End Beeper

Reset Time Beeper

Countdown start time: 10 minutes; Reset time: 5 minutes; Timer mode: Elapsed time;

Progress beeper: Off

10'00"

0'00"

5'00"

Countdown

End Beeper

Elapsed time

measurement

Start Time

Reset Time

· See "To configure the countdown timer" for information about setting up the timer.

Countdown Timer

The countdown timer can be set within a range of one

minute to 60 minutes. An alarm sounds when the

countdown reaches zero. The countdown timer has two

modes: auto-repeat and elapsed time, and a progress

beeper signals the progress of the countdown. All of this

makes the countdown timer a valuable tool for timing the

start of a yacht race.

· All of the operations in this section are performed in the

Countdown Timer Mode, which you enter by pressing

Configuring the Countdown Timer

The following are the settings you should configure before actually using the

countdown timer.

Countdown start time and reset time

Timer mode (auto-repeat, elapsed time)

Progress beeper on/off

Seconds

Minutes

Timekeeping Mode time

To configure the countdown timer

1. While the countdown start time is on the display in the

Countdown Timer Mode, hold down A until the

countdown start time setting starts to flash, which

indicates the setting screen.

· If the countdown start time is not displayed, use the

procedure under "To use the countdown timer" to

display it.

2. Press C to move the flashing in the sequence shown

below to select other settings.

Start

Time

Reset

Time

Timer

Mode

Progress

Beeper

3. When the setting you want to change is flashing, use D and B to change it as

described below.

Setting

Start Time

Reset Time

Timer Mode

Progress

Beeper

Screen

Button Operations

Use D (+) and B () to change the setting.

· You can set a start time in the range of 1 to 60 minutes

in 1-minute increments.

Use D (+) and B () to change the setting.

· You can set a reset time in the range of 1 to 5 minutes

in 1-minute increments.

Press D to toggle between the auto-repeat mode (

ON)

and the elapsed time mode (

OFF).

· An auto-repeat indicator ( ) appears when the auto-

repeat mode is selected.

Press D to toggle progress beeper on (

ON) and off (OFF).

· A progress beeper indicator ( ) appears when this

setting it turned on.

4. Press A to exit the setting screen.

· The reset time setting must be less than the countdown start time setting.

USER'S GUIDE 2534/2654

To use the countdown timer

In the Countdown Timer Mode, press D to start the

countdown timer.

· The countdown timer measurement operation continues

even if you exit the Countdown Timer Mode.

· The table below describes button operations you can

perform to control countdown operations.

To do this:

Stop the countdown operation

Resume a stopped countdown operation

Display the countdown start time

Stop the countdown operation and display the reset time

Start the countdown from the displayed reset time

Do this:

Press D.

Press D again.

While the countdown is

stopped, press B.

Press B.

Press D.

· The table below describes button operations you can perform during an elapsed

time measurement operation in the elapsed time mode.

To do this:

Stop the elapsed time operation

Resume a stopped elapsed time operation

Display the countdown start time

Stop the elapsed time operation and display the reset time

Start the countdown from the displayed reset time

Do this:

Press D.

Press D again.

While the elapsed time is

stopped, press B.

Press B.

Press D.

Alarms

You can set five independent Daily Alarms. When an

alarm is turned on, the alarm tone sounds when the alarm

time is reached. One of the alarms can be configured as a

snooze alarm or a one-time alarm, while the other four are

one-time alarms.

You can also turn on an Hourly Time Signal that causes

the watch to beep twice every hour on the hour, and a

brightness alarm that beeps whenever the watch is moved

from an area where it is dark to an area where it is light.

· There are five alarm screens numbered 1 through 5.

The hourly time signal screen is indicated by

:00. The

brightness alarm screen shows

ON or OFF.

· All of the operations in this section are performed in the

Alarm Mode, which you enter by pressing C.

Alarm number

Alarm time

(Hour : Minutes)

Timekeeping Mode time

To set an alarm time

1. In the Alarm Mode, use D to scroll through the alarm

screens until the one whose time you want to set is

displayed.

:00

ON or OFF

· You can configure Alarm 1 as a snooze alarm or a one-time alarm. Alarms 2

through

5 can be used as one-time alarms only.

· The snooze alarm repeats every five minutes.

2. After you select an alarm, hold down A until the hour setting of the alarm time

starts to flash. This indicates the setting screen.

3. Press C to move the flashing between the hour and minute settings.

4. While a setting is flashing, use D (+) and B () to change it.

· When setting the alarm time using the 12-hour format, take care to set the time

correctly as a.m. (no indicator) or p.m. (P indicator).

5. Press A to exit the setting screen.

Alarm Operation

The alarm sounds at the preset time for about 10 seconds. In the case of the snooze

alarm, the alarm operation is performed a total of seven times, every five minutes,

until you turn the alarm off or change it to a one-time alarm.

The watch also has a brightness alarm. When turned on, the brightness alarm causes

the watch to beep for 10 seconds when the watch is brought from the dark into the

light. The following are the conditions for brightness alarm operation.

· The watch needs to be in the dark for about 30 to 35 minutes for the brightness

alarm to become activated.

· The brightness alarm sounds about 15 to 20 minutes after the watch is next exposed

to light.

· The brightness alarm sounds only once and then turns off automatically.

Note

· Pressing any button stops the alarm tone operation.

· Performing any one of the following operations during a 5-minute interval between

snooze alarms cancels the current snooze alarm operation.

Displaying the Timekeeping Mode setting screen

Displaying the Alarm

1 setting screen

To test the alarm

In the Alarm Mode, hold down D to sound the alarm.

To turn Alarms

2 through 5

5 on and off

1. In the Alarm Mode, use D to select a one-time alarm

(alarm number

2 through 5).

2. Press B to toggle the displayed alarm on and off.

· Turning on a one-time alarm (2 through 5) displays the

one-time alarm on indicator (ALM) on its screen.

· The one-time alarm on indicator is displayed in all

modes.

· If any alarm is on, the alarm on indicator is shown on

the display in all modes.

One-time alarm on

indicator

To select the operation of Alarm

1. In the Alarm Mode, use D to select Alarm

2. Press B to cycle through the available settings in the sequence shown below.

· The applicable alarm on indicator (ALM or SNZ ALM) is displayed in all modes

when an alarm is turned on.

· The SNZ indicator flashes during the 5-minute intervals between alarms.

· Displaying the Alarm 1 setting screen while the snooze alarm is turned on

automatically turns off the snooze alarm (making Alarm

1 a one-time alarm).

SNZ ALM

ALM

SNZ indicator and one-time alarm on indicator

One-time alarm on

Snooze alarm on

Alarm off

To turn the hourly time signal and the brightness alarm on and off

1. In the Alarm Mode, use D to select the Hourly Time

Signal or the brightness alarm.

2. Press B to toggle the displayed item on and off.

· Turning on the Hourly Time Signal displays the hourly

time signal on indicator (SIG) on its screen.

· Turning on the brightness alarm displays the brightness

alarm on indicator (BRT) on its screen.

· The hourly time signal on indicator and brightness alarm

on indicator are displayed in all modes.

Hourly time signal on

indicator

Brightness alarm on

indicator

Stopwatch

The stopwatch lets you measure elapsed time, split times,

and two finishes.

· The display range of the stopwatch is 99 hours, 59

minutes, 59.99 seconds.

· The stopwatch continues to run, restarting from zero

after it reaches its limit, until you stop it.

· The stopwatch measurement operation continues even

if you exit the Stopwatch Mode.

· Exiting the Stopwatch Mode while a split time is frozen

on the display clears the split time and returns to

elapsed time measurement.

· All of the operations in this section are performed in the

Stopwatch Mode, which you enter by pressing C.

Seconds

1/100 second

Minutes

Hours

To measure times with the stopwatch

Start

Stop

Elapsed Time

Re-start

Clear

Stop

Split Time

Start

Split

Split release

Clear

Stop

Two Finishes

Start

Split

Stop

Clear

Split release

First runner

finishes.

Display time of

first runner.

Second runner

finishes.

Display time of

second runner.

(SPL displayed)

Backlight

The backlight uses an EL (electro-luminescent) panel that

causes the entire display to glow for easy reading in the

dark. The watch's auto light switch automatically turns on

the backlight when you angle the watch towards your face.

· The auto light switch must be turned on (indicated by

the auto light switch on indicator) for it to operate.

· See "Backlight Precautions" for other important

information about using the backlight.

To turn on the backlight manually

In any mode, press L to illuminate the display for about

one second.

· The above operation turns on the backlight regardless of

the current auto light switch setting.

Auto light switch

on indicator

About the Auto Light Switch

Turning on the auto light switch causes the backlight to turn on for about one second,

whenever you position your wrist as described below in any mode. Note that this

watch features a "Full Auto EL Light," so the auto light switch operates only when

available light is below a certain level. It does not turn on the backlight under bright

light.

Moving the watch to a position that is parallel to the ground and then tilting it towards

you more than 40 degrees causes the backlight to turn on.

Parallel to

ground

More than

USER'S GUIDE 2534/2654

Warning!

· Always make sure you are in a safe place whenever you are reading the

display of the watch using the auto light switch. Be especially careful when

running or engaged in any other activity that can result in accident or injury.

Also take care that sudden illumination by the auto light switch does not

surprise or distract others around you.

· When you are wearing the watch, make sure that its auto light switch is turned

off before riding on a bicycle or operating a motorcycle or any other motor

vehicle. Sudden and unintended operation of the auto light switch can create a

distraction, which can result in a traffic accident and serious personal injury.

To turn the auto light switch on and off

In the Timekeeping Mode, hold down D for about two seconds to toggle the auto light

switch on (AUTO EL displayed) and off (AUTO EL not displayed).

· The auto light switch on indicator (AUTO EL) is on the display in all modes while the

auto light switch is turned on.

Battery

This watch is equipped with a solar cell and a rechargeable battery (secondary

battery) that is charged by the electrical power produced by the solar cell. The

illustration shown below shows how you should position the watch for charging.

Example: Orient the watch so its

face is pointing at a light source.

· Note that charging efficiency drops

when any part of the solar cell is

blocked by clothing, etc.

· The illustration shows how to position

a watch with a resin band.

Important!

· Storing the watch for long periods in an area where there is no light or wearing it in

such a way that it is blocked from exposure to light can cause rechargeable battery

power to run down. Be sure that the watch is normally exposed to bright light

whenever possible.

Solar cell

· This watch employs a solar cell that converts light into electricity, which charges a

built-in rechargeable battery. Normally, the rechargeable battery should not need

replacement, but after very long use over a number of years, the rechargeable

battery may lose its ability to achieve a full charge. Should you notice problems with

getting the rechargeable battery to a full charge, contact your dealer or CASIO

distributor about having the rechargeable battery replaced.

· The rechargeable battery should be replaced with a CASIO-specified CTL1616

battery only. Other rechargeable batteries can cause damage to the watch.

· All data stored in memory is deleted, and the current time and all other settings

return to their initial factory defaults whenever battery power drops to Level 5 and

when you have the battery replaced.

· Turn on the watch's Power Saving function and keep it in an area normally exposed

to bright light when storing it for long periods. This helps to keep the rechargeable

battery from going dead.

Battery Power Indicator

The battery power indicator on the display shows you the current status of the

rechargeable battery's power.

Level

Battery Power

Indicator

(Charge Soon Alert)

Function Status

All functions enabled.

Beeper tone, backlight,

display, and buttons are

disabled.

All functions, including

timekeeping, are disabled.

Battery power indicator

· The flashing

indicator at Level 4 tells you that battery power is very low, and that

exposure to bright light for charging is required as soon as possible.

· At Level 5, all functions are disabled and settings return to their initial factory

defaults. Functions are enabled once again after the rechargeable battery is

charged, but you need to set the current time, date, and all other settings after the

battery is recharged to Level 3 from Level 5. Though the time appears on the display

after the battery is charged to Level 4, you will not be able to change the time setting

until the battery reaches Level 3.

· Leaving the watch in direct sunlight or some other very strong light source can

cause the battery power indicator to temporarily show a reading that is higher than

the actual battery level. The correct battery power indicator should appear after a

few minutes.

· If you use the backlight or any of the alarm functions a number of times during a

short period, RECOVER appears on the display and the following operations

become disabled until battery power recovers.

Backlight

Beeper tone

After some time, battery power will recover and RECOVER will disappear, indicating

that the above functions are enabled again.

Charging Precautions

Certain charging conditions can cause the watch to become very hot. Avoid leaving

the watch in the areas described below whenever charging its rechargeable battery.

Also note that allowing the watch to become very hot can cause its liquid crystal

display to black out. The appearance of the LCD should become normal again when

the watch returns to a lower temperature.

Warning!

Leaving the watch in bright light to charge its rechargeable battery can cause it

to become quite hot. Take care when handling the watch to avoid burn injury.

The watch can become particularly hot when exposed to the following

conditions for long periods.

· On the dashboard of a car parked in direct sunlight

· Too close to an incandescent lamp

· Under direct sunlight

Charging Guide

After a full charge, timekeeping remains enabled for up to about nine months (Module

2534)/11 months (Module 2654), while the watch is used under the conditions

described below.

Operating Conditions

· Watch is not exposed to light

· Display on 18 hours per day, sleep state 6 hours per day

· 1 backlight operation (1.5 seconds) per day

· 10 seconds of alarm operation per day

· 1 countdown timer operation per day

Charge Times

Exposing the watch to light for the periods shown below each day restores the power

used by the above operating conditions.

Exposure Level (Brightness)

Outdoor Sunlight (50,000 lux)

Sunlight Through a Window (10,000 lux)

Daylight Through a Window on a Cloudy Day

(5,000 lux)

Indoor Fluorescent Lighting (500 lux)

Approximate Exposure Time

5 minutes

24 minutes

48 minutes

8 hours

· Stable operation is promoted by frequent charging.

Recovery Times

The table below shows the amount exposure that is required to take the battery from

one level to the next.

Exposure Level

(Brightness)

Outdoor Sunlight

(50,000 lux)

Sunlight Through a

Window(10,000 lux)

Daylight Through a Window

on a Cloudy Day (5,000 lux)

Indoor Fluorescent Lighting

(500 lux)

Approximate Exposure Time

Level 5

Level 4

Level 3

Level 2

65 minutes (Module 2534)

1 hour (Module 2654)

4 hours

7 hours (Module 2534)

6 hours (Module 2654)

60 hours

18 hours (Module2534)

14 hours (Module 2654)

98 hours (Module 2534)

67 hours (Module 2654)

4 hours

19 hours

· The above exposure time values are all for reference only. Actual required exposure

times depend on lighting conditions.

Level 1

Reference

This section contains more detailed and technical information about watch operation.

It also contains important precautions and notes about the various features and

functions of this watch.

Power Saving Function

When turned on, the Power Saving function automatically

puts the watch into a sleep state whenever it is left in an

area where it is dark for 30 to 35 minutes. The sleep state

is indicated by a blank screen with SLEEP flashing on it.

In the sleep state, all functions are enabled, except for the

display.

· Wearing watch inside the sleeve of clothing can cause it

to enter the sleep state.

Auto Return Feature

If you leave a screen with flashing digits on the display for two or three minutes without

performing any operation, the watch automatically saves any settings you have made

up to that point and exits the setting screen.

Initial Screens

When you enter the Telememo, World Time, or Alarm Mode, the data you were

viewing when you last exited the mode appears first.

Data and Setting Scrolling

The B and D buttons are used in various modes and setting screens to scroll

through data on the display. In most cases, holding down these buttons during a scroll

operation scrolls through the data at high speed.

To recover from the sleep state

Perform any one of the following operations.

· Move the watch to a well-lit area. It can take up to five seconds for the display to turn

on.

· Press any button.

· Angle the watch towards your face for reading.

To turn Power Saving on and off

1. In the Timekeeping Mode, hold down A until the

seconds start to flash, which indicates the setting

screen.

2. Press C seven times until the Power Saving on/off

screen appears.

3. Press D to toggle Power Saving on (

ON) and off

(

OFF).

4. Press A to exit the setting screen.

· The Power Saving on indicator (SAVE) is on the display

in all modes while the Power Saving is turned on.

USER'S GUIDE 2534/2654

City Code Table

HNL

ANC

LAX

DEN

CHI

NYC

CCS

RIO

+05.5

+06.0

+06.5

+07.0

+08.0

+09.0

+09.5

+10.0

+11.0

+12.0

MUMBAI, KOLKATA

COLOMBO

JAKARTA, PHNOM PENH, HANOI, VIENTIANE

SINGAPORE, KUALA LUMPUR, BEIJING, TAIPEI,

MANILA, PERTH, ULAANBAATAR

SEOUL, PYONGYANG

DARWIN

MELBOURNE, GUAM, RABAUL

PORT VILA

CHRISTCHURCH, NADI, NAURU ISLAND

DELHI

DHAKA

YANGON

BANGKOK

HONG KONG

TOKYO

ADELAIDE

SYDNEY

NOUMEA

WELLINGTON

LONDON

PARIS

CAIRO

JERUSALEM

JEDDAH

TEHRAN

DUBAI

KABUL

KARACHI

Timekeeping

· Resetting the seconds to 00 while the current count is in the range of 30 to 59

causes the minutes to be increased by 1. In the range of 00 to 29, the seconds are

reset to

00 without changing the minutes.

· With the 12-hour format, the P (PM) indicator appears on the display for times in the

range of noon to 11:59 p.m. and no indicator appears for times in the range of

midnight to 11:59 a.m.

· With the 24-hour format, times are displayed in the range of 0:00 to 23:59, without

any indicator.

· The year can be set in the range of 2000 to 2039.

· The watch's built-in full automatic calendar automatically makes allowances for

different month lengths and leap years. Once you set the date, there should be no

reason to change it except when battery power drops to Level 5.

World Time

· The seconds count of the World Time is synchronized with the seconds count of the

Timekeeping Mode.

· The GMT differential is the time difference between the time zone where the city is

located and Greenwich Mean Time.

· GMT differential is calculated by this watch based on Universal Time Coordinated

(UTC) data.

Backlight Precautions

· The electro-luminescent panel that provides illumination loses power after very long

use.

· The illumination provided by the backlight may be hard to see when viewed under

direct sunlight.

· The watch may emit an audible sound whenever the display is illuminated. This is

due to vibration of the EL panel used for illumination, and does not indicate

malfunction.

· The backlight automatically turns off whenever an alarm sounds.

· Frequent use of the backlight runs down the battery.

Auto light switch precautions

· Wearing the watch on the inside of your wrist and movement or vibration of your arm

can cause the auto light switch to activate and illuminate the display. To avoid

running down the battery, turn off the auto light switch whenever engaging in

activities that might cause frequent illumination of the display.

· The backlight may not light if the face of the watch is

more than 15 degrees above or below parallel. Make

sure that the back of your hand is parallel to the ground.

· The backlight turns off in about one second, even if you

keep the watch pointed towards your face.

· Static electricity or magnetic force can interfere with

proper operation of the auto light switch. If the backlight

does not light, try moving the watch back to the starting

position (parallel with the ground) and then tilt it back

toward you again. If this does not work, drop your arm

all the way down so it hangs at your side, and then bring

it back up again.

More than 15 degrees

too high

· Under certain conditions, the backlight may not light until

about one second after you turn the face of the watch

towards you. This does not necessarily indicate

malfunction of the backlight.

· You may notice a very faint clicking sound coming from

the watch when it is shaken back and forth. This sound

is caused by mechanical operation of the auto light

switch, and does not indicate a problem with the watch.

(space)

Sort Table

HONOLULU

ANCHORAGE

LOS ANGELES

DENVER

CHICAGO

NEW YORK

CARACAS

RIO DE JANEIRO

City

GMT

Other major cities in same time zone

Code

Differential

11.0

10.0

09.0

08.0

07.0

06.0

05.0

04.0

03.0

02.0

PAGO PAGO

PAPEETE

NOME

SAN FRANCISCO, LAS VEGAS, VANCOUVER,

SEATTLE, DAWSON CITY

EL PASO, EDMONTON

HOUSTON, DALLAS/FORT WORTH, NEW ORLEANS,

MEXICO CITY, WINNIPEG

MONTREAL, DETROIT, MIAMI, BOSTON, PANAMA CITY,

HAVANA, LIMA, BOGOTA

LA PAZ, SANTIAGO, PORT OF SPAIN

SAO PAULO, BUENOS AIRES, BRASILIA,

MONTEVIDEO

GMT

LON

PAR

CAI

JRS

JED

THR

DXB

KBL

KHI

01.0

+00.0

+01.0

+02.0

+03.0

+03.5

+04.0

+04.5

+05.0

PRAIA

DUBLIN, LISBON, CASABLANCA, DAKAR, ABIDJAN

MILAN, ROME, MADRID, AMSTERDAM, ALGIERS,

HAMBURG, FRANKFURT, VIENNA, STOCKHOLM,

BERLIN

ATHENS, HELSINKI, ISTANBUL, BEIRUT, DAMASCUS,

CAPE TOWN

KUWAIT, RIYADH, ADEN, ADDIS ABABA, NAIROBI,

MOSCOW

SHIRAZ

ABU DHABI, MUSCAT

MALE

DEL

DAC

RGN

BKK

HKG

TYO

ADL

SYD

NOU

WLG

· Based on data as of June 2002.