CASIO GW1401D-4A - Owner's Manual Immediate Download

Operation Guide 3357

To do this:

Change the city code

Toggle between Daylight Saving Time

(ON) and Standard Time (OFF)

Toggle between 12-hour (12H) and

24-hour (24H) timekeeping

Do this:

Press D (east).

Press D.

MO0405-EA

Getting Acquainted

Congratulations upon your selection of this CASIO watch. To get the most out of your

purchase, be sure to read this manual carefully and keep it on hand for later reference

when necessary.

Expose the watch to bright light to charge its battery before using it.

You can use this watch even as its battery is being charged by exposure to bright

light.

· Be sure to read "Power Supply" for important information you need to know

when exposing the watch to bright light.

If the digital display of the watch is blank...

If the Power Saving on indicator is flashing on the display,

it means that the Power Saving function has turned off the

display to conserve power. Power Saving automatically

turns off the display and enters a sleep state whenever

the watch is left for a certain period where it is dark.

· The initial factory default setting is Power Saving on.

· The watch will recover from the sleep state if you move it

to a well-lit area,* if you press any button, or if you angle

the watch towards your face for reading.

* It can take up to two seconds for the display to turn on.

· See "Power Saving" for more information.

Power saving on indicator

Digital display

About This Manual

· Button operations are indicated using the letters shown

in the illustration.

· Most of the display examples in this manual show only

the digital display, without the analog hands.

· Each section of this manual provides you with the

information you need to perform operations in each

mode. Further details and technical information can be

found in the "Reference" section.

Digital display

Hour hand

Minute hand

General Guide

· Press C to change from mode to mode.

· In any mode, press B to illuminate the face of the watch.

· The Battery Level Screen shows the current battery level. See "Battery Power

Levels" for more information.

WED

NYC

STW

World Time Mode

Alarm Mode

Stopwatch Mode

Timekeeping Mode

Press C.

Battery Level Screen

Hand Setting Mode

Timekeeping

Use the Timekeeping Mode to set and view the current time and date.

· In the Timekeeping Mode, press A to cycle through the digital time screens as

shown below.

Time

Seconds

Date

Press A.

Month. Day

Hour : Minutes

PM indicator

Day of week

2 seconds

Setting the Digital Time and Date

This watch is preset with a number of city codes, each of which represents the time

zone where that city is located. When setting the digital time, it is important that you

select the correct city code for your Home City (the city where you normally use the

watch). If your location is not included in the preset city codes, select the preset city

code that is in the same time zone as your location.

· Note that all of the times for the World Time Mode city codes are displayed in

accordance with the digital time and date settings you configure in the Timekeeping

Mode.

To set the digital time and date

1. In the Timekeeping Mode, hold down A until the city

code starts to flash, which indicates the setting screen.

2. Press D to select the city code you want.

· Make sure you select your Home City code before

changing any other setting.

· See "City Code Table" for a complete list of available

city codes.

l l l l l

3. Press C to move the flashing in the sequence shown below to select other settings.

Seconds

Hour

Minutes

12/24-Hour

Format

Month

Year

DST

Day

Power

Saving

City Code

4. When the setting you want to change is flashing, use D to change it as described

below.

· The following steps explain how to configure timekeeping settings only.

Screen

Reset the seconds to 00

Change the hour or minutes

Change the year

Change the month or day

Press D.

Press D(to increase).

5. Press A to exit the setting screen.

· When you exit the setting screen, the analog hands are adjusted automatically to

match the digital time. See "Analog Timekeeping" for more information.

· See "Daylight Saving Time (DST)" for details about the DST setting.

· For information about specifying how long the face of the watch remains illuminated,

see "To specify the illumination duration".

· For details about configuring settings for the Power Saving feature, see "Power

Saving".

Daylight Saving Time (DST)

Daylight Saving Time (summer time) advances the time setting by one hour from

Standard Time. Remember that not all countries or even local areas use Daylight

Saving Time.

To toggle the Timekeeping Mode digital time between DST and Standard Time

1. In the Timekeeping Mode, hold down A until the city

code starts to flash, which indicates the setting screen.

2. Press C once and the DST setting screen appears.

3. Press D to toggle between Daylight Saving Time (ON

displayed) and Standard Time (OFF displayed).

4. Press A to exit the setting screen.

· The DST indicator appears on the display to indicate

that Daylight Saving Time is turned on.

l ll

lll

Analog Timekeeping

The analog time of this watch is synchronized with the digital time. The analog time

setting is adjusted automatically whenever you change the digital time.

Note

· The hands for the analog timepiece move to adjust to a new setting whenever any of

the following occurs.

When you change the digital time setting

When you change the Home City code and/or DST setting

· If the analog time does not match the digital time for some reason, use the

procedure below to adjust the analog time to the digital time.

· Whenever you need to adjust both the digital and the analog time settings manually,

make sure you adjust the digital setting first.

· Depending on how much the hands have to move in order to adjust to the digital

time, it may take some time before they stop moving.

To adjust the analog time

1. In the Timekeeping Mode, press C five times to enter

the Hand Setting Mode.

2. Hold down A until the current digital time starts to

flash, which indicates the analog time setting screen.

3. Press D to advance the analog time setting by 20

seconds.

· Holding down D advances the analog time setting at

high speed.

· If you need to advance the analog time setting a long way, hold down D until the

time starts advancing at high speed, and then press B. This locks the high-speed

hand movement, so you can release the two buttons. High-speed hand movement

continues until you press any button. It will also stop automatically after the time

advances 12 hours or if an alarm starts to sound.

4. Press A to exit the setting screen.

· The minute hand will be adjusted slightly to match the seconds when you exit the

setting screen.

· To return to the Timekeeping Mode, press C.

l l l l

l l

Operation Guide 3357

World Time

World Time digitally displays the current time in 30 cities

(29 time zones) around the world.

· For full information on city codes, see the "City Code

Table".

· All of the operations in this section are performed in the

World Time Mode, which you enter by pressing C.

NYC

City code

Current time in the

zone of the

selected city code

To view the time in another city

In the World Time Mode, press D to scroll eastwardly through city codes (time

zones).

· The city code is displayed for about two seconds, and then it is replaced with the

current time for that city code. Pressing A while the time is displayed in the World

Time Mode causes the city code of the currently selected zone to appear.

· When the currently selected time zone is one that includes mostly ocean, a value

indicating the zone's Greenwich Mean Time differential appears in place of a city

code.

· If the current time shown for a city is wrong, check your Home City time settings and

make the necessary changes.

To toggle a city code time between Standard Time and Daylight Saving Time

1. In the World Time Mode, use D to display the city

code (time zone) whose Standard Time/Daylight Saving

Time setting you want to change.

2. Hold down A to toggle between Daylight Saving Time

(DST indicator displayed) and Standard Time (DST

indicator not displayed).

· The DST indicator appears on the display whenever you

display a city code for which Daylight Saving Time is

turned on.

· You cannot toggle between Daylight Saving Time and Standard Time if the displayed

city code is GMT or the city code that is currently selected as the Home City in the

Timekeeping Mode. To change the DST setting of your Home City, use the

procedure under "To toggle the Timekeeping Mode digital time between DST and

Standard Time" .

· Note that the DST/Standard Time setting affects only the currently displayed city

code. Other city codes are not affected.

DST indicator

Alarm

When the alarm is turned on, the alarm sounds when the

alarm time is reached. You can also turn on an Hourly

Time Signal, which will cause the watch to beep twice

every hour on the hour.

· When the alarm is turned on, the alarm screen

alternates between qmOo (alarm on) and the current

alarm time (hour and minutes). When the alarm is off,

qmOw (alarm off) remains on the alarm screen.

· All of the operations in this section are performed in the

Alarm Mode, which you enter by pressing C.

· Pressing D in the Alarm Mode toggles between the

alarm screen and Hourly Time Signal screen.

2 seconds

On/Off status

Alarm Screen

Hourly Time Signal Screen

Press D.

To set the alarm time

1. In the Alarm Mode, press D to display the alarm

screen.

2. Hold down A until the hour setting of the alarm time

starts to flash, which indicates the setting screen.

· This operation automatically turns on the alarm.

3. Press C to move the flashing between the hour and

minute settings.

4. While a setting is flashing, use D (+) and B () to

change it.

· When setting the alarm time using the 12-hour format,

take care to set the time correctly as a.m. (no

indicator) or p.m. (P indicator).

5. Press A to exit the setting screen.

Alarm Operation

The alarm sounds at the preset time for about 10 seconds, regardless of the mode the

watch is in.

l ll

lll

Alarm time

(Hour : Minutes)

· To stop the alarm tone after it starts to sound, press any button.

· Alarm and Hourly Time Signal operations are performed in accordance with the

Timekeeping Mode digital time.

To test the alarm

In the Alarm Mode, hold down D to sound the alarm.

To turn the alarm and the Hourly Time Signal on and off

1. In the Alarm Mode, press D to select the alarm or the

Hourly Time Signal screen.

2. Press A to toggle the currently selected function on

(Oo displayed) and off (Ow displayed).

· The alarm on indicator and the Hourly Time Signal on

indicator remain on the display in all modes while these

functions are turned on.

Hourly time signal

on indicator

Alarm on indicator

On/Off status

Stopwatch

The stopwatch lets you measure elapsed time, split times,

and two finishes.

· The display range of the stopwatch is 59 minutes, 59.99

seconds.

· The stopwatch continues to run, restarting from zero

after it reaches its limit, until you stop it.

· Exiting the Stopwatch Mode while a split time is frozen

on the display clears the split time and returns to

elapsed time measurement.

· The elapsed time measurement operation continues

even if you exit the Stopwatch Mode.

· All of the operations in this section are performed in the

Stopwatch Mode, which you enter by pressing C.

STW

Minutes

Seconds

Split Time

Start

Split

Split release

Clear

Stop

*2Split times are displayed by cycling alternately through the split indicator ( SPL),

a minute and seconds screen, and a 1/100 second screen.

lll

lllll

llll

lll

Start

Stop

Elapsed Time

Re-start

Clear

Stop

*1When elapsed time measurement is stopped, the display alternates between a

minute and seconds screen, and a 1/100 second screen at 2-second intervals.

To measure times with the stopwatch

1/100 second

Minutes' Seconds

*3When a split time operation is stopped, the display cycles through the same values

as those described in *2 above. In this case, however, the minute symbol ( ') and

the seconds symbol ( '') do not flash.

Two Finishes

Start

Split

Split stop

Clear

Split release

First runner

finishes.

Display time of

first runner.

Second runner

finishes.

Display time of

second runner.

Illumination

Two LEDs (light-emitting diodes) illuminate the face of the

watch for easy reading in the dark. The watch's auto light

switch automatically illuminates the face when you angle

the watch towards your face.

· The auto light switch must be turned on (indicated by

the auto light switch on indicator) for it to operate.

· You can specify 1.5 seconds or 3 seconds as the

illumination duration.

· See "Illumination Precautions" for other important

information.

To illuminate the face of the watch manually

In any mode (except when a setting screen is on the display), press B to illuminate

the face of the watch.

· The above operation turns on illumination regardless of the current auto light switch

setting.

Auto light switch

on indicator

Parallel to

ground

More than

About the Auto Light Switch

Turning on the auto light switch causes the face to illuminate, whenever you position

your wrist as described below in any mode. Note that this watch features a "Full Auto

LED Light", so the auto light switch operates only when available light is below a

certain level. It does not illuminate the face under bright light.

Moving the watch to a position that is parallel to the ground and then tilting it

towards you more than 40 degrees causes illumination to turn on.

· Wear the watch on the outside of your wrist.

Warning!

· Always make sure you are in a safe place whenever you are reading the face

of the watch using the auto light switch. Be especially careful when running or

engaged in any other activity that can result in accident or injury. Also take

care that sudden illumination by the auto light switch does not surprise or

distract others around you.

· When you are wearing the watch, make sure that its auto light switch is turned

off before riding on a bicycle or operating a motorcycle or any other motor

vehicle. Sudden and unintended operation of the auto light switch can create a

distraction, which can result in a traffic accident and serious personal injury.

To turn the auto light switch on and off

In any mode (except when a setting screen is on the display), hold down B for about

two seconds to toggle the auto light switch on (

displayed) and off (

not

displayed).

· The auto light switch on indicator (

) is on the display in all modes while the auto

light switch is turned on.

· The auto light switch turns off automatically whenever battery power drops to Level 3.

· The auto light switch is disabled, regardless of its on/off setting, when the Hand

Setting Mode's setting screen.

Operation Guide 3357

To specify the illumination duration

1. In the Timekeeping Mode, hold down A until the city

code starts to flash, which indicates the setting screen.

2. Press C three times to move the flashing to the

seconds setting.

3. Press B to toggle the illumination duration setting

between 3 seconds ( ) and 1.5 seconds (

4. Press A to exit the setting screen.

l l l l l ll

lll

Power Supply

This watch is equipped with a solar cell and a special rechargeable battery

(secondary battery) that is charged by the electrical power produced by the solar cell.

The illustration shown below shows how you should position the watch for charging.

Example: Orient the watch so its face

is pointing at a light source.

· The illustration shows how to position

a watch with a resin band.

· Note that charging efficiency drops

when any part of the solar cell is

blocked by clothing, etc.

· Normally, you should try to keep the

watch outside of your sleeve as much

as possible. Charging is significantly

reduced if the face is only partially

covered.

Solar cell

Important!

· Storing the watch for long periods in an area where there is no light or wearing it in

such a way that it is blocked from exposure to light can cause rechargeable battery

power to run down. Make sure that the watch is normally exposed to bright light

whenever possible.

· This watch uses a special rechargeable battery to store power produced by the solar

cell, so regular battery replacement is not required. However, after very long use, the

rechargeable battery may lose its ability to achieve a full charge. If you experience

problems getting the special rechargeable battery to fully charge, contact your

dealer or CASIO distributor about having it replaced.

· Never try to remove or replace the watch's special battery yourself. Use of the wrong

type of battery can damage the watch.

· The current time and all other settings return to their initial factory defaults whenever

battery power drops to Level 4 and when you have the battery replaced.

· Turn on the watch's Power Saving function and keep it in an area normally exposed

to bright light when storing it for long periods. This helps to keep the rechargeable

battery from going dead.

Battery Power Levels

The digital display show you the current level of the rechargeable battery's power.

· All of the watch's functions are available when

(high) or

(medium) is

indicated on the Battery Level Screen.

Function Status

All functions enabled.

Except for internal

timekeeping and the charge

indicator, all functions and

display indicators are

disabled.

All functions disabled.

Level

(Charge

soon alert)

Digital Display

Charge indicator

l lll

llll

· Level 1 and Level 2 are indicated on the Battery Level Screen only. Level 3 and

Level 4 are indicated in all modes.

· The flashing charge indicator at Level 3 tells you that battery power is very low, and

that exposure to bright light for charging is required as soon as possible.

· When the battery level approaches Level 3, the analog hands move automatically to

the 12 o'clock position. Charge the battery as soon as possible when this happens.

All of the digital screen indicators flash while the analog hands are in motion.

· At Level 4, all functions are disabled and settings return to their initial factory

defaults. Functions are enabled once again after the rechargeable battery is

charged, but you need to set the digital time and date, after the battery reaches

Level 3 from Level 4. You will not be able to set any of the other settings until the

battery reaches Level 2 after dropping to Level 4.

· Display indicators reappear as soon as the battery is charged from Level 4 to Level 3.

· If the analog time and digital time do not match after the watch recovers to Level 2

from Level 3 or Level 4 , adjust the analog hand setting so it matches the digital time.

· Leaving the watch exposed to direct sunlight or some other very strong light source

can cause the digital display to temporarily show a reading that is higher than the

actual battery level. The correct battery level should be indicated after a few minutes.

Recover Indicator

If you use illumination or alarms a number of times during

a short period, the recover indicator (R) appears on the

display and the following operations become disabled until

battery power recovers.

Illumination; Beeper tone; Coordination between digital

and analog timekeeping

After some time, battery power will recover and the

recover indicator will disappear, indicating that the above

functions are enabled again.

· If the battery drops to Level 3 while the recover indicator is on the display, the

Battery Level Screen will indicate

. Charge the battery as soon as possible.

· If the recover indicator appears frequently, it probably means that remaining battery

power is low. Leave the watch in bright light to allow it to charge.

lll

llll

l l

Recover indicator

Charging Precautions

Certain charging conditions can cause the watch to become very hot. Avoid leaving

the watch in the areas described below whenever charging its rechargeable battery.

Also note that allowing the watch to become very hot can cause its liquid crystal

display to black out. The appearance of the LCD should become normal again when

the watch returns to a lower temperature.

Warning!

Leaving the watch in bright light to charge its rechargeable battery can cause it

to become quite hot. Take care when handling the watch to avoid burn injury.

The watch can become particularly hot when exposed to the following

conditions for long periods.

· On the dashboard of a car parked in direct sunlight

· Too close to an incandescent lamp

· Under direct sunlight

Charging Guide

After a full charge, timekeeping remains enabled for up to about 15 months.

· The following table shows the amount of time the watch needs to be exposed to light

each day in order to generate enough power for normal daily operations.

Exposure Level (Brightness)

Outdoor Sunlight (50,000 lux)

Sunlight Through a Window (10,000 lux)

Daylight Through a Window on a Cloudy Day

(5,000 lux)

Indoor Fluorescent Lighting (500 lux)

Approximate Exposure Time

7 minutes

24 minutes

39 minutes

7 hours

· Since these are the specs, we can include all the technical details.

· Watch is not exposed to light

· Internal timekeeping

· Display on 18 hours per day, sleep state 6 hours per day

· 1 light operation (1.5 seconds) per day

· 10 seconds of alarm operation per day

· Stable operation is promoted by frequent charging.

Recovery Times

The table below shows the amount exposure that is required to take the battery from

one level to the next.

· The above exposure time values are all for reference only. Actual required exposure

times depend on lighting conditions.

54 hours

203 hours

328 hours

15 hours

56 hours

90 hours

Outdoor Sunlight (50,000 lux)

Sunlight Through a Window

(10,000 lux)

Daylight Through a Window

on a Cloudy Day (5,000 lux)

Indoor Fluorescent Lighting

(500 lux)

Approximate Exposure Time

Level 4

Level 3

Level 2

Level 1

3 hours

9 hours

14 hours

169 hours

Exposure Level

(Brightness)

Reference

This section contains more detailed and technical information about watch operation.

It also contains important precautions and notes about the various features and

functions of this watch.

Power Saving

When turned on, Power Saving automatically enters a sleep state whenever the watch

is left for a certain period in an area where it is dark. The table below shows how

watch functions are affected by Power Saving.

· There are actually two sleep state levels: "display sleep" and "function sleep".

Elapsed Time in Dark

60 to 70 minutes

(Display Sleep)

6 or 7 days

(Function Sleep)

Operation

Digital display off, but all functions are enabled and the

power saving on indicator flashes on the display

· Digital display off, but the power saving on indicator

flashes on the display

· All functions, including analog timekeeping, disabled

· Internal timekeeping maintained

· Wearing the watch inside your sleeve can cause it to enter the sleep state.

· The watch will not enter the sleep state while the digital time is between 6:00 AM

and 9:59 PM. If the watch is already in the sleep state when the digital time reaches

6:00 AM, however, it will remain in the sleep state.

· The analog hands move to the 12 o'clock position when the watch enters the

function sleep state. If the analog time and digital time do not match after the watch

recovers from the function sleep state, adjust the analog hand setting so it matches

the digital time.

· The watch will not enter the sleep state while it is in the Stopwatch Mode.

To recover from the sleep state

Perform any one of the following operations.

· Move the watch to a well-lit area. It can take up to two seconds for the display to turn

on.

· Press any button.

· Angle the watch towards your face for reading.

To turn Power Saving on and off

1. In the Timekeeping Mode, hold down A until the city

code starts to flash, which indicates the setting screen.

2. Press C nine times until the Power Saving on/off

screen appears.

3. Press D to toggle Power Saving on (jsOo) and off

(jsOw).

4. Press A to exit the setting screen.

· The Power Saving on indicator is on the display in all

modes while Power Saving is turned on.

Auto Return Features

· The watch automatically returns to the Timekeeping Mode if you do not perform any

button operation for two or three minutes while the Battery Level Screen is

displayed, or while in the Alarm, or Hand Setting Mode.

· If you leave a screen with flashing digits on the display for two or three minutes

without performing any operation, the watch automatically exits the setting screen.

l l l l l l lll

lll

Power saving

on indicator

Scrolling

The B and D buttons are used in various modes and setting screens to scroll

through data on the display. In most cases, holding down these buttons during a scroll

operation scrolls through the data at high speed.

Operation Guide 3357

Initial Screens

When you enter the Timekeeping, World Time, or Alarm Mode, the data you were

viewing when you last exited the mode appears first.

Timekeeping

· Resetting the seconds to 00 while the current count is in the range of 30 to 59

causes the minutes to be increased by 1. In the range of 00 to 29, the seconds are

reset to 00 without changing the minutes.

· The year can be set in the range of 2000 to 2099. The day of the week is calculated

automatically in accordance with the date.

· The watch's built-in full automatic calendar makes allowances for different month

lengths and leap years. Once you set the date, there should be no reason to change

it except after you have the watch's battery replaced or when battery power drops to

Level 4.

· The current time for all city codes in the Timekeeping Mode and World Time Mode is

calculated in accordance with the Greenwich Mean Time (GMT) differential for each

city, based on your Home City time setting.

· GMT differential is calculated by this watch based on Universal Time Coordinated

(UTC*) data.

* UTC is the world-wide scientific standard of timekeeping. It is based upon carefully

maintained atomic (cesium) clocks that keep time accurately to within microseconds.

Leap seconds are added or subtracted as necessary to keep UTC in sync with the

Earth's rotation. The reference point for UTC is Greenwich, England.

12-hour/24-hour Timekeeping Formats

The 12-hour/24-hour timekeeping format you select in the Timekeeping Mode is

also applied in all other modes.

· With the 12-hour format, the P (PM) indicator appears on the display for times in the

range of noon to 11:59 p.m. and no indicator appears for times in the range of

midnight to 11:59 a.m.

· With the 24-hour format, times are displayed in the range of 0:00 to 23:59, without

any indicator.

Illumination Precautions

· The illumination provided by the light may be hard to see when viewed under direct

sunlight.

· Illumination automatically turns off whenever an alarm sounds.

· Frequent use of illumination shortens the battery operating time.

Auto light switch precautions

· Wearing the watch on the inside of your wrist, movement of your arm, or vibration of

your arm can cause frequent activation of the auto light switch and illumination of the

face of the watch. To avoid running down the battery, turn off the auto light switch

whenever engaging in activities that might cause frequent illumination of the face.

· Note that wearing the watch under your sleeve while the auto light switch is turned

on can cause frequent illumination of the face and can run down the battery.

· Illumination may not turn on if the face of the watch is

more than 15 degrees above or below parallel. Make

sure that the back of your hand is parallel to the ground.

· Illumination turns off after the preset illumination

duration (see "To specify the illumination duration"),

even if you keep the watch pointed towards your face.

More than 15 degrees

too high

· Static electricity or magnetic force can interfere with proper operation of the auto

light switch. If illumination does not turn on, try moving the watch back to the starting

position (parallel with the ground) and then tilt it back towards your face again. If this

does not work, drop your arm all the way down so it hangs at your side, and then

bring it back up again.

· Under certain conditions, illumination may not turn on until about one second after

you turn the face of the watch towards you. This does not necessarily indicate

malfunction of the auto light switch.

· You may notice a very faint clicking sound coming from the watch when it is shaken

back and forth. This sound is caused by mechanical operation of the auto light

switch, and does not indicate a problem with the watch.

Honolulu

Anchorage

Los Angeles

Denver

Chicago

New York

Caracas

Rio De Janeiro

London

Paris

Berlin

HNL

ANC

LAX

DEN

CHI

NYC

CCS

RIO

GMT

LON

PAR

BER

11.0

10.0

09.0

08.0

07.0

06.0

05.0

04.0

03.0

02.0

01.0

+00.0

+01.0

Pago Pago

Papeete

Nome

San Francisco, Las Vegas, Vancouver,

Seattle/Tacoma, Dawson City, Tijuana

El Paso, Edmonton, Culiacan

Houston, Dallas/Fort Worth,

New Orleans, Mexico City, Winnipeg

Montreal, Detroit, Miami, Boston,

Panama City, Havana, Lima, Bogota

La Paz, Santiago, Port of Spain

Sao Paulo, Buenos Aires, Brasilia, Montevideo

Praia

Dublin, Lisbon, Casablanca, Dakar, Abidjan

Milan, Rome, Madrid, Amsterdam, Algiers, Hamburg,

Frankfurt, Vienna, Stockholm

City

GMT

Other major cities in same time zone

Code

Differential

City Code Table

Athens

Cairo

Jerusalem

Jeddah

Tehran

Dubai

Kabul

Karachi

Delhi

Dhaka

Yangon

Bangkok

Hong Kong

Seoul

Tokyo

Adelaide

Sydney

Noumea

Wellington

+02.0

+03.0

+03.5

+04.0

+04.5

+05.0

+05.5

+06.0

+06.5

+07.0

+08.0

+09.0

+09.5

+10.0

+11.0

+12.0

Helsinki, Istanbul, Beirut, Damascus,

Cape Town

Kuwait, Riyadh, Aden, Addis Ababa, Nairobi, Moscow

Shiraz

Abu Dhabi, Muscat

Male

Mumbai, Kolkata

Colombo

Jakarta, Phnom Penh, Hanoi, Vientiane

Singapore, Kuala Lumpur, Beijing, Taipei, Manila, Perth,

Ulaanbaatar

Pyongyang

Darwin

Melbourne, Guam, Rabaul

Port Vila

Christchurch, Nadi, Nauru Island

ATH

CAI

JRS

JED

THR

DXB

KBL

KHI

DEL

DAC

RGN

BKK

HKG

SEL

TYO

ADL

SYD

NOU

WLG

· Based on data as of December 2003.