CASIO AWE10D-7E - Owner's Manual Immediate Download

USER'S GUIDE 2705

Stopwatch Mode

Dual Time Mode

Alarm Mode

General Guide

· Some models have a white-on-black display.

· Press A to change from mode to mode.

Timekeeping Mode

Calendar Mode

[ Modules 2337/2338 ]

Press A.

About the Backlight

· Press L to illuminate the display for about 2 seconds.

· The backlight of this watch employs an electro-luminescent (EL) light, which

loses its illuminating power after very long term use.

· Frequent use of the backlight shortens the battery life.

· The watch may emit an audible sound whenever the display is illuminated.

This does not indicate malfunction of the watch.

· The illumination provided by the backlight may be hard to see when viewed

under direct sunlight.

· The backlight automatically turns off whenever an alarm sounds.

· When the backlight is turned on, it blinks whenever the minute hand moves.

This is normal, and does not indicate malfunction of the watch.

· The backlight of Module 2338 illuminates both the digital display and analog

face. The backlight of Module 2337 illuminates the digital display only. The

backlight of Modules 2374, 2384 and 2705 illuminates the analog face only.

Timekeeping Mode

· Use this mode to set the current time. An incorrect digital time setting will

result in incorrect operation of the calendar.

To set the time and date

Seconds

12/24

Hour

Minutes

Hour

Minutes

Seconds

PM indicator

Minute hand

Hour hand

Hold down C.

Press C.

1. Hold down C until the seconds digits start to flash.

2. Press A to reset the seconds to 00. If you press A while the seconds

count is in the range of 30 to 59, the seconds are reset to 00 and 1 is added

to the minutes. If the seconds count is in the range of 00 to 29, the minutes

count is unchanged.

3. Press C to move the selection to the hour digits.

4. Press A to increase the hour digits. Holding down A changes the hour

digits at high speed.

5. Press C to move the selection to the minutes digits.

6. Press A to increase the minutes digits. Holding down A changes the

minutes digits at high speed.

7. Press C to move the selection to 12/24.

8. Press A to toggle the timekeeping format between 12-hour and 24-hour.

· When 12-hour format is selected, the indicator P appears on the display to

indicate "p.m." times. There is no indicator for "a.m." times.

9. Press C to complete the procedure.

· If you do not operate any button for a few minutes while a selection is

flashing, the flashing stops and the watch goes back to the Timekeeping

Mode automatically.

To set the hands

When in any Mode, press B with a thin object to advance the analog time

setting. Each press of B advances the time by 20 seconds. Three presses

advance by one minute.

Holding down B advances the analog setting at high speed. You can only

advance the setting and cannot reverse it.

1. Hold down C until the month digits start to flash.

2. Press A to increase the month digits. Holding down A changes the digits

at high speed.

3. Press C to move the selection to day digits.

4. Press A to increase the day digits. Holding down A changes the digits at

high speed.

5. Press C to move the selection to the day of the week indication.

6. Press A to advance to the next day. Holding down A changes the

indication at high speed.

7. Press C to complete the procedure.

· If you do not operate any button for a few minutes while a selection is

flashing, the flashing stops and the watch goes back to the Calendar Mode

automatically.

Calendar Mode

To set the date

Month

Day of week

Day

Month

Day

Day of week

Hold down C.

Press C.

1. Hold down C until the hour digits start to flash.

2. Press A to increase the hour digits. Holding down A changes the digits at

high speed.

· The format (12-hour and 24-hour) of the alarm time matches the format you

select for normal timekeeping.

3. Press C to move the selection to the left minutes digit.

4. Press A to increase the left minutes digit. Holding down A changes the

digit at high speed.

5. Press C to move the selection to the right minutes digit.

6. Press A to increase the right minutes digit. Holding down A changes the

digit at high speed.

7. Press C to move Daily Alarm and Hourly Time Signal on and off setting.

8. Press A to change the status of the Daily Alarm and Hourly Time Signal in

the following sequence.

· At this time Daily Alarm and Hourly Time Signal automatically turn on.

Alarm Mode

When the Daily Alarm is turned on, an alarm sounds for 20 seconds at the

preset time each day. When the Hourly Time Signal is switched on, the watch

beeps every hour on the hour.

To set the alarm time and to turn the Daily Alarm and Hourly Time Signal on

and off

Hour

Alarm/Hourly Time Signal setting

Right

minutes

digit

Left

minutes

digit

Hour Minutes

Alarm on indicator

Hourly Time Signal on indicator

Hold down

Press

Press C.

9. Press C to complete the procedure.

· If you do not operate any button for a few minutes while a selection is

flashing, the flashing stops and the watch goes back to the Alarm Mode

automatically.

Hourly Time

Signal only

Daily Alarm

only

Both OFF

Both ON

[Module 2374]

[Modules 2384/2705]

[Modules

2337/2338]

Press

To stop the alarm

· Press any button to stop the alarm after it starts to sound.

To test the alarm and select an alarm tone

Hold down A in any mode (except when making any settings) to sound the

alarm.

Each time you test the alarm, a four different alarm tones. The alarm tone you

select is used for the Daily Alarm and Hourly Time Signal.

· Note that holding down A also changes the mode.

USER'S GUIDE 2705

Hour

Minutes

12/24

Dual Time Mode

To set the Dual Time

1. Hold down C until the hour digits start to flash.

2. Press A to increase the hour digits. Holding down A changes the digits at

high speed.

3. Press C to move the selection to the minutes digits.

4. Press A to increase the minutes digits. Holding down A changes the digits

at high speed.

5. Press C to move the selection to 12/24.

6. Press A to toggle the timekeeping format between 12-hour and 24-hour.

· When 12-hour format is selected, the indicator P appears on the display to

indicate "p.m." times. There is no indicator for "a.m." times.

7. Press C to complete the procedure.

· If you do not operate any button for a few minutes while a selection is

flashing, the flashing stops and the watch goes back to the Dual Time Mode

automatically.

· In the Dual Time Mode, the seconds count is synchronized with the seconds

count of the Timekeeping Mode.

Hour

Minutes

Seconds

Press C.

Hold down C.

Press C.

PM indicator

Stopwatch Mode

The Stopwatch Mode lets you measure elapsed time.

The range of the stopwatch is 59 minutes 59.99

seconds.

To use the Stopwatch

1. Press C to start the stopwatch.

2. Press C to stop the time measurement.

· You can press C as many times as you want to

resume and stop timing.

3. After you are finished using the stopwatch, hold

down C to clear the stopwatch time to all zeros.

Minutes

Seconds

1/100 second