CANON MSC1 - Service Manual Immediate Download

CANON STAPLER SOTRER-L1 MS-C1 REV.0 NOV. 1998 PRINTED IN JAPAN (IMPRIME AU JAPON)

REVSION 0

NOV. 1998

FY8-13F9-000

STAPLER SORTER-L1

MS-C1

CANON STAPLER SOTRER-L1 MS-C1 REV.0 NOV. 1998 PRINTED IN JAPAN (IMPRIME AU JAPON)

IMPORTANT

THIS DOCUMENTATION IS PUBLISHED BY CANON INC., JAPAN, TO SERVE AS A SOURCE

OF REFERENCE FOR WORK IN THE FIELD.

SPECIFICATIONS AND OTHER INFORMATION CONTAINED HEREIN MAY VARY SLIGHTLY

FROM ACTUAL MACHINE VALUES OR THOSE FOUND IN ADVERTISING AND OTHER

PRINTED MATTER.

ANY QUESTIONS REGARDING INFORMATION CONTAINED HEREIN SHOULD BE DIRECTED

TO THE COPIER SERVICE DEPARTMENT OF THE SALES COMPANY.

THIS DOCUMENTATION IS INTENDED FOR ALL SALES AREAS, AND MAY CONTAIN IN-

FORMATION NOT APPLICABLE TO CERTAIN AREAS.

Printed in Japan

Imprimé au Japon

Use of this manual should be strictly su-

pervised to avoid disclosure of confidential

information.

Prepared by

OFFICE IMAGING PRODUCTS TECHNICAL SUPPORT DEPARTMENT 1

OFFICE IMAGING PRODUCTS TECHNICAL SUPPORT DIVISION

CANON INC.

5-1, Hakusan, 7-chome, Toride-City, Ibaraki-Pref., 302-8501, Japan

CANON STAPLER SOTRER-L1 MS-C1 REV.0 NOV. 1998 PRINTED IN JAPAN (IMPRIME AU JAPON)

This Service Manual provides basic facts and figures needed to service the Stapler

Sorter-L1/MS-C1 in the field and consists of the following:

Chapter 1

"General Descriptions" shows features, specifications, and names of

external parts and how to operate the sorter.

Chapter 2

"Operations and Timing" discusses the sorter's mechanical and

electrical systems by function and various timing of operation.

Chapter 3

"Mechanical System" shows how to disassemble, assemble, and

adjust the sorter.

Chapter 4

"Maintenance and Inspection" gives lists of periodically replaced parts

and consumables/ durables and a scheduled servicing chart.

Chapter 5

"Troubleshooting" shows how to troubleshoot possible faults and gives

electrical parts arrangement diagrams, LED/check pin diagrams by

PCB, and self diagnosis tables.

In addition to the above chapters, this Service Manual contains an Appendix

consisting of a general timing chart, a signals/abbreviations list, communications signals

list, a General circuit diagram controller circuit diagrams.

For installation, see the Installation Procedure that comes with the mounting kit for the

Stapler Sorter-L1 and MS-C1. (Hereafter, the Stapler Sorter-L1 will be referred to as the

"stapler sorter" and the MS-C1, "non-staple sorter.")

INTRODUCTION

CANON STAPLER SOTRER-L1 MS-C1 REV.0 NOV. 1998 PRINTED IN JAPAN (IMPRIME AU JAPON)

The following rules apply throughout this Service Manual:

1. Each chapter contains sections explaining the purpose of specific functions and

the relationship between electrical and mechanical systems with reference to the

timing of operation.

In the diagrams,

represents the path of mechanical driveÑwhere a signal

name accompanies the symbol

, the arrow indicates the direction of the

electric signal.

The expression "turn on the power" means flipping on the power switch, closing

the front door, and closing the delivery unit door, which results in supplying the

machine with power.

2. In the digital circuits, '1' is used to indicate that the voltage level of a given signal is

"High," while '0' is used to indicate "Low." (The voltage value, however, differs from

circuit to circuit.)

In practically all cases, the internal mechanisms of a microprocessor cannot be

checked in the field. Therefore, the operations of the microprocessors used in the

machines are not discussed: they are explained in terms of from sensors to the

input of the DC controller PCB and from the output of the DC controller PCB to the

loads.

The descriptions in this Service Manual are subject to change without notice for

product improvement or other purposes, and major changes will be communicated in the

form of Service Information bulletins.

All service persons are expected to have a good understanding of the contents of this

Service Manual and all relevant Service Information bulletins and be able to identify and

isolate faults in the machine.

CONTENTS

CHAPTER 1 GENERAL DESCRIPTION

FEATURES..................................1-1

II.

SPECIFICATIONS .......................1-2

III.

NAMES OF PARTS .....................1-5

EXTERNAL VIEW .......................1-5

CROSS SECTION ......................1-6

IV.

OPERATION................................1-7

OPERATION PANEL ...................1-7

STAPLING ...................................1-8

RESUPPLY OF STAPLES TO

STAPLER ................................. 1-10

REMOVING A STAPLE JAM .... 1-12

REMOVING PAPER

CLOGGING .............................. 1-13

CHAPTER 2 OPERATIONS AND TIMING

CONSTRUCTION .......................2-1

FUNCTIONAL CONSTRUCTION . 2-1

ELECTRICAL CIRCUITRY .........2-2

SORTER CONTROLLER INPUT/

OUTPUT......................................2-3

COMMUNICATION BETWEEN

COPIER AND SORTER ..............2-6

II.

BASIC OPERATIONS .................2-7

OUTLINE .....................................2-7

BASIC OPERATIONS .................2-9

III.

FEED DRIVE SYSTEM ............ 2-19

OUTLINE .................................. 2-19

CONTROLLING THE FEED

SPEED ..................................... 2-21

OVERSTACK CONDITION ...... 2-22

JAM .......................................... 2-24

IV.

STAPLER UNIT DRIVE

SYSTEM................................... 2-26

OUTLINE .................................. 2-26

STAPLER UNIT ........................ 2-28

CONTROLLING THE SWINGING

MOVEMENT OF THE STAPLER

UNIT ......................................... 2-33

HOLDING THE PAPER ............ 2-37

STAPLING OPERATION TIMING

(3 DOCUMENTS, NO. OF

SHEETS OF PAPER: 3) ........... 2-38

BIN UNIT DRIVE SYSTEM ...... 2-39

OUTLINE .................................. 2-39

BIN UNIT .................................. 2-40

CONTROLLING THE GUIDE

BAR .......................................... 2-45

SENSORS INSIDE BIN UNIT .. 2-48

OTHER SENSORS .................. 2-49

VI. POWER SUPPLY ..................... 2-50

CANON STAPLER SOTRER-L1 MS-C1 REV.0 NOV. 1998 PRINTED IN JAPAN (IMPRIME AU JAPON)

iii