MP-C545
USER
MANUAL
Canon
User's Manual
MULTIPASSTM
C545
COLOR BUBBLE JETTM PRINTER
FAX · SCANNER · COPIER
ii
Preface
Copyright
This manual is copyrighted by Canon Computer Systems, Inc. (CCSI) with all
rights reserved. Under the copyright laws, this manual may not be reproduced in
any form, in whole or part, without prior written consent of CCSI.
Portions copyrighted by Infowave Software Inc. and Second Glance Software.
©1999 Canon Computer Systems, Inc.
Disclaimer
Canon Computer Systems, Inc. has reviewed this manual thoroughly in order to
make it an easy to use guide for your Canon MultiPASS system. All statements,
technical information, and recommendations in this guide and in any guides or
related documents are believed reliable, but the accuracy and completeness
thereof are not guaranteed or warranted, and they are not intended to be, nor
should they be understood to be, representations or warranties concerning the
products described.
Your MultiPASS and the software media included with your system have been sold
to you subject to the limited warranties set forth in the warranty and license
agreement enclosed with the respective products. All software is licensed AS IS, as
described in the license agreement enclosed with the software media. Further,
CCSI reserves the right to make changes in the specifications of the products
described in this guide at any time without notice and without obligation to notify
any person of such changes.
Trademarks
Canon, BCI, BJ, Bubble Jet, MultiPASS, ScanGear, and UHQ are trademarks and
SelectExchange is a service mark of Canon Inc.
PowerPrint, SpoolMaster, and the Infowave logo are trademarks of Infowave
Software Inc.
Apple, Finder, ColorSync and Macintosh are registered trademarks of Apple
Computer, Inc. ScanTastic is a trademark of Second Glance Software.
Portions copyrighted by Infowave Software, Inc. and Second Glance Software.
All other product and brand names are trademarks or service marks of their
respective owners.
ENERGY STAR
® COMPLIANT
As an ENERGY STAR® Partner, Canon U.S.A., Inc. has determined that this
product meets the ENERGY STAR® guidelines for energy efficiency.
Preface
iii
Users in the U.S.A.
PRE-INSTALLATION REQUIREMENTS FOR CANON FACSIMILE
EQUIPMENT
A.
Location
Supply a suitable table, cabinet, or desk. See Appendix A for the unit's
dimensions and weight.
B.
Order Information
1.
Only a single line, touch-tone or rotary telephone set is to be used.
2.
Order an RJ11-C modular jack (USOC code), which should be
installed by the phone company. If the RJ11-C jack is not present,
installation cannot occur.
3.
Order a normal business line from your telephone company's business
representative. The line should be a regular voice grade line or the
equivalent. Use one line per unit.
DDD (DIRECT DISTANCE DIAL) LINE
-or-
IDDD (INTERNATIONAL DIRECT DISTANCE DIAL) LINE IF YOU
COMMUNICATE OVERSEAS
C.
Power Requirements
This equipment should be connected to a standard 120 volt AC, three-wire
grounded outlet only. Do not connect this unit to an outlet or power line
shared with other appliances that cause "electrical noise". Air conditioners,
electric typewriters, copiers, and machines of this sort generate electrical
noise which often interferes with communications equipment and the
sending and receiving of documents.
n Canonrecommendsanindividuallinefollowingindustrystandards,e.g.the
2500 (Touch Tone) or 500 (Rotary/Pulse Dial) telephones. A dedicated
extension off a PBX unit without "Call Waiting" can be used with your
MultiPASS. Key telephone systems are not recommended because they send
non-standard signals to individual telephones for ringing and special codes,
which may cause a fax error.
iv
Preface
CONNECTION OF THE EQUIPMENT
This equipment complies with Part 68 of the FCC rules. On the rear panel of this
equipment is a label that contains, among other information, the FCC
Registration Number and Ringer Equivalence Number (REN) for this equipment.
If requested, this information must be given to the telephone company. This
equipment may not be used on coin service provided by the telephone company.
Connection to party lines is subject to state tariffs.
An FCC compliant telephone cord and modular jack is provided with this
equipment. This equipment is designed to be connected to the telephone network
or premises wiring using a compatible modular jack which is Part 68 compliant.
See Installation instructions for details.
The REN is used to determine the quantity of devices which may be connected to
the telephone line. Excessive RENs on the telephone line may result in the devices
not ringing in response to an incoming call. In most, but not all areas, the sum of
the RENs should not exceed five (5.0). To be certain of the number of devices that
may be connected to the line, as determined by the total RENs, contact the
telephone company to determine the maximum REN for the calling area.
IN CASE OF EQUIPMENT MALFUNCTION
Should any malfunction occur which cannot be corrected by the procedures
described in this User's Manual, disconnect the equipment from the telephone line
or unplug the power cord. The telephone line should not be reconnected
or the power cord plugged in until the problem is completely resolved. Users
should contact Canon Authorized Service Facilities for servicing of equipment.
Information regarding Authorized Service Facility locations can be obtained by
calling the Canon Computer Systems Customer Care Center. (See page 1-9 for
details.)