CANON E1 FINISHER - Service Manual Immediate Download

CANON FINISHER-E1 REV.0 JAN. 1999 PRINTED IN JAPAN (IMPRIME AU JAPON)

REVSION 0

FY8-13FU-000

FINISHER-E1

JAN. 1999

CANON FINISHER-E1 REV.0 JAN. 1999 PRINTED IN JAPAN (IMPRIME AU JAPON)

IMPORTANT

THIS DOCUMENTATION IS PUBLISHED BY CANON INC., JAPAN, TO SERVE AS A SOURCE

OF REFERENCE FOR WORK IN THE FIELD.

SPECIFICATIONS AND OTHER INFORMATION CONTAINED HEREIN MAY VARY SLIGHTLY

FROM ACTUAL MACHINE VALUES OR THOSE FOUND IN ADVERTISING AND OTHER

PRINTED MATTER.

ANY QUESTIONS REGARDING INFORMATION CONTAINED HEREIN SHOULD BE DIRECTED

TO THE COPIER SERVICE DEPARTMENT OF THE SALES COMPANY.

THIS DOCUMENTATION IS INTENDED FOR ALL SALES AREAS, AND MAY CONTAIN INFOR-

MATION NOT APPLICABLE TO CERTAIN AREAS.

Printed in Japan

Imprimé au Japon

Use of this manual should be strictly su-

pervised to avoid disclosure of confidential

information.

Prepared by

OFFICE IMAGING PRODUCTS TECHNICAL SUPPORT DIVISION

OFFICE IMAGING PRODUCTS QUALITY ASSURANCE CENTER

CANON INC.

5-1, Hakusan 7-chome, Toride-shi, Ibaraki, 302-8501 Japan

CANON FINISHER-E1 REV.0 JAN. 1999 PRINTED IN JAPAN (IMPRIME AU JAPON)

This Service Manual contains basic data and figures for the Finisher-E1 needed to

service the machine in the field.

Chapter 1 General Description introduces the finisher's features, specifications, and

names of parts, and shows how to operate the finisher.

Chapter 2 Basic Operation discusses the principles of operation used for the finisher's

mechanical and electrical systems. It also explains the timing at which these

systems are operated.

Chapter 3 Mechanical System discusses how the finisher is constructed mechanically,

and shows how it may be disassembled/assembled and adjusted.

Chapter 4 Maintenance and Inspection provides tables of periodically replaced parts and

consumables and durables, together with a scheduled servicing chart.

Chapter 5 Troubleshooting provides tables of maintenance/inspection, standards/

adjustments, and problem identification (image fault/malfunction).

Appendix contains diagrams showing electrical parts arrangement, tables of

signals, tables of special tools, tables of solvents/oils, and a general timing

chart.

For installation, see the Installation Procedure that comes with the finisher.

The descriptions in this Service Manual are subject to change without notice for

product improvement or other purposes, and major changes will be communicated in the

form of Service Information bulletins.

All service persons are expected to have a good understanding of the contents of this

Service Manual and all relevant Service Information bulletins and be able to identify and

isolate faults in the machine.

INTRODUCTION

CANON FINISHER-E1 REV.0 JAN. 1999 PRINTED IN JAPAN (IMPRIME AU JAPON)

iii

CONTENTS

FEATURES ..................................1-1

II.

SPECIFICATIONS ........................1-2

III. OPERATING THE MACHINE .......1-6

IV. MAINTENANCE BY THE USER .. 1-11

BASIC CONSTRUCTION ............2-1

II.

BASIC OPERATIONS ..................2-6

III. FEEDING DRIVE SYSTEM .........2-9

IV. INTERMEDIARY PROCESSING

TRAY ASSEMBLY ..................... 2-11

STAPLING ................................. 2-42

VI. OPERATIONS OF THE STACK

TRAY ......................................... 2-45

VII. DETECTING JAMS ................... 2-53

VIII. POWER SUPPLY ...................... 2-58

CHAPTER 3 MECHANICAL SYSTEM

CHAPTER 2 BASIC OPERATION

CHAPTER 1 GENERAL DESCRIPTION

EXTERNALS AND CONTROLS ..3-1

II.

FEEDING SYSTEM .....................3-6

III. PROCESSING TRAY ...................3-7

IV. RETURNING ROLLER ............. 3-16

STACK TRAY ............................. 3-24

VI. STACK TRAY LIFTER UNIT ...... 3-25

VII. STAPLER .................................. 3-35

VIII. PCBs ......................................... 3-36

CHAPTER 4 MAINTENANCE AND INSPECTION

PERIODICALLY REPLACED

PARTS .........................................4-1

II.

CONSUMABLES AND

DURABLES ..................................4-1

III. SCHEDULED MAINTENANCE ...4-1