COPYRIGHT © 1999 CANON INC.
CANON FINISHER - D1 REV.0 FEB. 1999 PRINTED IN JAPAN (IMPRIME AU JAPON)
FY8-13FF-000
REVISION 0
FEB. 1999
SERVICE
MANUAL
FINISHER - D1
COPYRIGHT © 1999 CANON INC.
CANON FINISHER - D1 REV.0 FEB. 1999 PRINTED IN JAPAN (IMPRIME AU JAPON)
COPYRIGHT
1999 CANON INC.
Printed in Japan
Use of this manual should be strictly
supervised to avoid disclosure of confi-
dential information.
Imprimé au Japon
THE
INFORMATION
CONTAINED
HEREIN
IS
PUBLISHED
BY
CANON,
INC.,
JAPAN.
SPECIFICATIONS AND OTHER INFORMATION CONTAINED HEREIN MAY DIFFER SLIGHTLY FROM
ACTUAL MACHINE VALUES OR THOSE FOUND IN ADVERTISING AND OTHER PRINTED MATTER.
ANY QUESTIONS REGARDING INFORMATION CONTAINED HEREIN SHOULD BE DIRECTED TO THE
COPIER SERVICE DEPARTMENT OF THE SALES COMPANY.
IMPORTANT
Prepared by
OFFICE IMAGING PRODUCTS TECHNICAL SUPPORT DIVISION
5-1, Hakusan 7-chome, Toride-City, Ibaraki, 302-8501 Japan
CANON INC.
COPYRIGHT © 1999 CANON INC.
CANON FINISHER - D1 REV.0 FEB. 1999 PRINTED IN JAPAN (IMPRIME AU JAPON)
INTRODUCTION
This Service Manual contains basic data and figures on the Finisher-D1 needed to
service the machine in the field.
CHAPTER 1 General Description introduces the finisher's features and specifications,
and shows how to operate the finisher.
CHAPTER 2 Basic Operation provides outlines of the finisher's various mechanical
workings, and explains the principles used for the finisher's various control mechanisms in
view of the functions of electrical and mechanical units and in relation to their timing of
operation.
CHAPTER 3 Mechanical System shows how the finisher's various mechanical
workings are constructed, and how the finisher may be disassembled/assembled and
adjusted.
CHAPTER 4 Maintenance and Servicing provides tables of periodically replaced
parts and consumables/durables and scheduled servicing charts.
CHAPTER 5 Troubleshooting provides tables of maintenance/inspection, standards/
adjustments, and problem identification (image fault/malfunction).
APPENDIX contains a general timing chart and general circuit diagrams.
The descriptions in this Service Manual are subject to change without notice for
product improvement or other purposes, and major changes will be communicated in the
form of Service Information bulletins.
All service persons are expected to have a good understanding of the contents of this
Service Manual and all relevant Service Information bulletins and be able to identify and
isolate faults in the machine.
COPYRIGHT © 1999 CANON INC.
CANON FINISHER - D1 REV.0 FEB. 1999 PRINTED IN JAPAN (IMPRIME AU JAPON)
CHAPTER 1 GENERAL DESCRIPTION
I.
FEATURES ................................ 1-1
II.
SPECIFICATIONS ...................... 1-2
A.
Specifications ........................ 1-2
B.
Cross Section ........................ 1-4
III. OPERATING THE FINISHER .... 1-5
A.
Removing Jams from The
Finisher .................................. 1-5
B.
Removing Jams in Sort, Group, or
Staple Sort Mode ................... 1-7
C. Replacing the Staple Cartridge
............................................. 1-10
D. Removing Staple Jams in the
Stapler Unit .......................... 1-13
IV. MAINTENANCE BY THE USER
.................................................. 1-15
CONTENTS
CHAPTER 2 OPERATIONS
I.
BASIC OPERATIONS ................ 2-1
A.
Specifications ........................ 2-1
B.
Outline of Electrial Circuitry ... 2-2
C. Inputs to and Outputs from the
Finisher Controller PCB......... 2-3
II.
FEEDING/DRIVE SYSTEM ...... 2-14
A.
Outline .................................. 2-14
B.
Feeding/Delivery ................. 2-19
C. Job Offset ............................. 2-22
D. Releasing the Knurled Belt
............................................ 2-29
E.
Buffer Path ........................... 2-34
III. CONTROLLING THE PADDLE
.................................................. 2-39
IV. CONTROLLING THE TRAY
AUXILIARY PLATE .................. 2-40
V.
STAPLING ................................ 2-42
VI. TRAY MOVEMENT .................. 2-50
VII. FANS ........................................ 2-54
VIII. POWER SUPPLY ..................... 2-56
IX. DETECTING JAMS .................. 2-59
CHAPTER 3 MECHANICAL SYSTEM
I.
EXTERNALS AND CONTROLS
.................................................... 3-1
II.
PROCESSING TRAY UNIT ..... 3-13
III. TRAY B UNIT ........................... 3-21
IV. KNURLED BELT RELEASING UNIT
.................................................. 3-28
V.
KNURLED BELT ...................... 3-30
VI. BUFFER ROLLER UNIT .......... 3-31
VII. STAPLER UNIT ........................ 3-35
VIII. PCBs ......................................... 3-42