ALPINE VPA-S001 - Owner's Manual Immediate Download

ß OWNER'S MANUAL

Please read this manual to maximize your enjoyment of the outstanding performance and feature

capabilities of the equipment, then retain the manual for future reference.

!"#

!"#$%&'()*+,-./%#0123456789:6;<=>?@A)BC

Accessories/

Guide for Installation and Connections/

!"#$

VPA-S001

CD/Video CD Changer

IMPORTANT

Please record the serial number of your unit in

the space provided here and keep it as a perma-

nent record. The serial number plate is located

on the top of the unit.

68P11199Y15-A

Printed in Korea (Y)

English

'Before Installation

Perform the installation at a location that is level. Make sure the parking

brake is on and the ignition is OFF.

Refer to the Connections and Operation sections before you proceed

with installation.

Install the Shuttle properly using the "L" type brackets supplied. Improp-

er installation can degrade performance (causing the player to skip,

mis-track, etc.).

Install the Shuttle in the trunk of the car or another suitable location. In

the passenger compartment of some cars, the glove box, under the dash

or center console may be able to accommodate the VPA-S001. Make sure

that the installation will not interfere with the safe operation of the vehi-

cle or with passenger leg room.

The VPA-S001 should be mounted to a stable surface. If no stable surface

is available, you must build a mounting board for the Shuttle. Choose a

location which allows easy access to insert and remove the CD magazi-

ne. Determine the mounting location and position. Then have the

necessary parts ready before you begin installation.

NOTE:

For the vertical installation be sure to install the Shuttle with the CD

magazine slot facing upward.

Installation of Shuttle

With the VPA-S001, CDs are automatically removed from and reinserted

into the CD magazine, DO NOT mount the unit upside down, as this could

cause the mechanism to become misaligned.

Floor Base Plates

"L" Type Brackets

(For Horizontal Mounting)

!"#$%

"L" Type Brackets

(For Vertical Mounting)

!"#$%

Hexagon Flange-head

Screws (M5x15)

!"#$ jR

Warning

DO NOT DISASSEMBLE OR ALTER. Doing so may lead to accident, fire or electric shock.

KEEP SMALL ARTICLES OUT OF THE REACH OF CHILDREN. If swallowed, consult a physician imme-

diately.

BEFORE WIRING, DISCONNECT THE CABLE FROM THE NEGATIVE () BATTERY TERMINAL. Failure

to do so may result in electric shock or injury due to electrical shorts.

MAKE THE CORRECT CONNECTIONS. Failure to do so may cause fire or accident to occur.

DO NOT CUT AWAY THE WIRE SHEATH AND USE POWER FOR OTHER EQUIPMENT. Doing so may

exceed the current carrying capacity of the wire and result in fire or electric shock.

DO NOT INSTALL IN LOCATIONS WHICH MIGHT HINDER VEHICLE OPERATION OR CREATE

HAZARDS FOR VEHICLE OCCUPANTS. Doing so may obstruct forward vision or hamper movement.

DO NOT CONTACT, DAMAGE OR OBSTRUCT PIPES, FLUID LINES OR WIRING WHEN DRILLING

HOLES. Failure to take such precautions may result in fire or cause an accident or injuries.

DO NOT USE NUTS OR BOLTS IN THE BRAKE SYSTEM WHEN MAKING INSTALLATION OR GROUND

CONNECTIONS. Never use safety-related parts such as bolts or nuts in the steering or brake

systems or tanks to make wiring installations or ground connections. Using such parts could disable

control of the vehicle and cause brake failure, other accident or injury.

ARRANGE THE WIRING SO IT IS NOT CRIMPED OR PINCHED. Route the cables and wiring so as

not to be crimped by moving parts or make contact with sharp or pointed spots which might damage

the wiring. Failure to do so may cause failure of unit or vehicle.

HAVE THE WIRING AND INSTALLATION DONE BY EXPERTS. The wiring and installation of this unit

requires special technical skill and experience. To ensure safety, always contact the dealer where

you purchased this unit to have the work done.

HALT USE IMMEDIATELY IF A PROBLEM APPEARS. When problems occur such as a lack of sound

or video, foreign objects inside the unit, smoke coming out, or noxious odors, stop use immediately

and contact the dealer where you bought the equipment. Failure to do so may result in an accident

or injury.

DO NOT OPERATE THE EQUIPMENT OR LOOK AT THE SCREEN WHILE DRIVING THE VEHICLE.

Operating the equipment may distract the driver from looking ahead of the vehicle and cause

accident. Always stop the vehicle in a safe location before operating this equipment.

DO NOT USE THIS EQUIPMENT FOR PURPOSES OTHER THAN STATED FOR THE VEHICLE. Failure to

do so may result in electric shock or injury.

DO NOT PLACE FOREIGN OBJECTS IN INSERTION SLOTS OR GAPS. Do not insert hands, fingers

or foreign objects in the disc or cassette insertion slots, or in gaps during monitor startup/storage.

Doing so may result in personal injury or damage to the equipment.

Caution

USE SPECIFIED ACCESSORY PARTS AND INSTALL THEM SECURELY. Use of other than designated

parts may damage this unit internally or may not securely install the unit in place as parts that come

loose may create hazards.

DO NOT INSTALL IN LOCATIONS WITH HIGH MOISTURE OR DUST. A high incidence of moisture or

dust that penetrates into this unit may cause smoke or fire.

Points to Observe for Safe Usage

SERIAL NUMBER/

INSTALLATION DATE/

INSTALLATION TECHNICIAN/

!"#

PLACE OF PURCHASE/

Hexagon Flange-head

Nuts (M6)

!"#$ jS

Input/Output Label (L/R)

CD Magazine

`a=

Dust Cover Label (L/R)

Ai-NET Cable

^áJkbq=

Index Label Sheet

Hexagon Flange-head

Bolts (M6 x 50)

!"#$ jS

Hexagon Washer-head

Bolts (M4 x 8)

!"#$ jQ

Binder

Hexagon Bolts (M6 x 25)

! jS

Plastic Bag for Shipping

Screws

!"#$%&'

VOCAL Switch

sl`^i=

CAUTION:

Do not install the Shuttle near the vehicle's fuel tank. This will prevent the

mounting screws from damaging the tank.

Never install the Shuttle on the rear deck or front dashboard of the car.

The temperatures caused by direct sunlight at these locations can reach

extremes that could cause permanent damage to the Shuttle. The Alpine

Warranty will be voided in cases where this caution has been ignored

and results in damage to the Shuttle.

Shipping Screws

Three screws have been attached to the bottom of the Shuttle for protec-

tion during shipment. Remove these screws before using. Keep the

removed screws in the plastic bag attached to the connector of Shuttle.

Mounting in the Trunk

Make sure the mounting angle of the Shuttle installation will fall within the

five preset positions (22.5° to 45° from the horizontal or vertical position). The

Shuttle is preset at the factory for horizontal mounting. If you wish to install

it at any other angle, change the spring configuration as shown.

1. Remove the covers provided at both left and right sides of the unit by

pressing claws of the covers in the direction shown by the arrow.

2. Change the position of the spring with your finger.

Use the figure to determine which spring position would be best suited for

your chosen mounting location. If the spring configuration is incorrect or

the spring positions on the left and right sides are not the same, the shock

absorbing mechanism will not function properly. This will prevent the CD

Shuttle from operating at its best.

3. Mount the covers at the left and right sides as they were attached originally.

(H)

(V)

67.5

22.5

°(H)

(V)

' Parts identifications

1 Bus Selector Switch (Fig. 1)

This switch is used to select Ai-NET or Standard-Bus operation. Change

the switch position using a small screwdriver or other pointed object.

Ai-NET system

Standard-Bus System

Ai Std.

CAUTION:

When switching the Bus Selector Switch, make sure there are no cables

attached to the VPA-S001.

2 Ai-NET Cable (Included in the VPA-S001) (Fig. 2)

The Ai-NET Cable provided, allows connection to any Alpine Ai-NET com-

patible, CD Shuttle Controller. Make sure that the "L" type connector of

the Ai-NET cable is attached to the Controller and the straight connector

is attached to the VPA-S001.

3 Input/Output Identification Label (Fig. 2)

The Ai-NET system has an input and an output. The input connectors are

Gray and outputs are Black. Use the corresponding Input/Output ID la-

bels to maintain proper connections when extension cables are used.

' Connections

Ai-NET Connection (Fig. 3)

· Bus Selector Switch: Set to "Ai" position.

4 Ai-NET Connector

5 Head unit, etc. with Ai-NET System

6 Ai-NET Input Connector

Mini-Bus Connection (Fig. 4)

· Bus Selector Switch: Set to "Std." position.

4 Ai-NET Connector

7 Head unit, etc. with Standard-Bus System

8 8 pin DIN Input Connector

9 Standard-Bus Adaptor (Sold Separately)

Switch Connections (Fig. 5)

0 Switch Connector

@ VOCAL Switch (Included)

When attaching the switch, be sure to clean off dust, water drop and

oil on the spot where the switch is attached. The connection cables

should be securely fixed using the provided Mount Base.

Connecting to TV Monitor (Fig. 5)

! VIDEO Output Connector

# RCA Extension Cable (Included)

$ To VIDEO Input Terminal

% TV Monitor

^ VISUAL Switch

Place the Visual switch in the desired TV system position, NTSC or PAL.

Change the switch position using a small screwdriver or other point-

ed object.

NTSC

PAL

NTSC

PAL

' Cautions for Connections

· Head unit with Ai-NET capability and Ai-NET Cable (Fig. 6)

Connect the Ai-NET cable as illustrated.

· Connect the cables by referring to the illustration. Incorrect connec-

tion may cause damage.

· Check the cables and read the attached labels carefully.

Fig. 1

Fig. 2

Fig. 3

Fig. 4

Fig. 6

Fig. 5

CD/VIDEO CD CHANGER

HIGH

SPEED

DISC

CHANGE

CD/VIDEO

COMPATIBLE

OPEN

OUT

VPA-S001

NTSC

PAL

(RCS PONTOISE B 338 101 280)

Jook Jin Won Saek Print Co.

109, Cho-dong, Jung-gu,

Seoul, Korea

Ai Std.

VPA-S001

Ai Std.

!"#$%&'()*+,-./0123

!"#$%&

Mount Base

Velcro tape

RCA extension cable

o`^=

!"#$%&'(

!"#$%&'()*+,-.

!"#$%&

!"#$%&'()%&*+,)-./012

!"#$%&'()

*+,-#$./0123456789:04#3;<.1=>?

!"#$

!"#$%&'()

!"#$%&'(

This label is intended to alert the user to the presence of important operating

instructions.

Failure to heed the instructions will result in severe injury or death.

This label is intended to alert the user to the presence of important operating

instructions.

Failure to heed the instructions can result in injury or material damage.

Caution

Warning

!"#$!%&'()*+,-./0

!"#$%&'()*+

!"#$!%&'()*+,-./0

!"#$%&'()*+,-.

!"#$%&

!"#$%&'

!"#$ %&'()*+,

!"#$%&

!"#$

!"#$%

!"#$%&'

!"#

!"#$%&'()*+,

!"#$

!"#$%&'()

!"#$%&'()*+,-./0"

!"#$%&'$()*+,-./012$3

!"#$%&'()*+,-./0123456

!"#$%&'()

!"#$%&

!"#$%

!"#$%&'

!"#$%&$'(

!"#$%&'()'*

!"#$%&'(&)*

!"#$%

!"#$%&'("')

!"#$%&'()*+,)-&./0123

!"#$%&'()

!"#$%&'()*+,-./012345(678$"9:;<

!"#$%&'(

!"#$%&'()

!"#$%&'()!*+$,-

!"#$

!"#$%&

!"#$%&"'

!"#$

!"#$%&'(

!"#$%

!"#$%&'()

!"#$%&'()*

!"#$%&'()

!"#$%&'()*+,

!"#$%&'($)*

!"#$%

!"#$%&'(

!"#$%&'()*+,

!"#$%&'()

!"#$%&'%(

!" L

!"#$%& '()#*+

!"#$%&'()*+

Read this manual carefully before starting operation and use this system safely. We cannot be

responsible for problems resulting from failure to observe the instructions in this manual.

This manual uses various pictorial displays to show how to use this product safely and to avoid harm

to yourself and others and damage to your property. Here is what these pictorial displays mean.

Understanding them is important for reading this manual.

Meaning of displays

!"#$%&'()*+%,-./$0

!"#$%&'()*+,

!"=i=

!"#$%

!"#$%&'$()*+, -./0

!"#$%&'()*+,-./01

!"#$%&'()*+,-

!"#$%&'()=sm^JpMMN=

!"#$%&'()*+,-./0123'45

sm^JpMMN=

!"#$%&'()*+,#$-.'/0123456789

=`a=

!"#$%&'(

!"#$%& !'()*+,-./

!"#$%&'=`a=

!"#$

sm^JpMMN=

!"=`a=

!"#$=`a=

!"#$%&'()*

!"#$%&'

!"#$%&'()*+,-./012345678*+

!"#$%&'()*+,-./0123

!"#$%&'()*+

!"#$%&'()*+,-./0123

!"#$%&'()*=P=

!"#$%

!"#$%&'()*

!"#$%&'(

!"#$

!"#$%=R=

!" #$%&'()*+,-./0123 =OOKR=

=QR=

!"#$%&'()*+

!"#$%&'()*+,

!"#$%

!"#$%&'()*+,-./0&'

!"#$%&

!"#$%&'()*+,-"./012

!"#$%&'()* !"#$+,-./0#1$2345678-

!"#$%&'()*+,

!"#$%&'()*+,-.

!"#$%=N

!"#$=^áJkbq=

!"#$

!"#$%&'()*+,-./012

^áJkbq=

!"#

!"#$%&'()*+,-./0=sm^JpMMN=

2 ^áJkbq=

!"#=sm^JpMMN=

!"=O

=^áJkbq=

!"#$%=^äéáåÉ=^áJkbq=

=`a=

!"# ^áJ

kbq=

=i=

!"#$%&'()*+

#$%=sm^JpMMN=

!"#$%&'=O

^áJkbq=

!"#$%!"#&'#$()*+,'#&()*-,

!"#$%&'()*(+,-./01'23

^áJkbq=

!=P

!"#$%&'^á

4 ^áJkbq=

=^áJkbq=

!"#$%

6 ^áJkbq=

!"#$%=Q

!"#$%&'píÇ

4 ^áJkbq=

!"#$%&'()*

8 U= =afk=

!"#$%&'()*

!"#=R

@ sl`^i=

!"#$%&'

!"#$%&'()*+,-./0#12345678)9:

!"#"$%&=R

=EsfablF=

# o`^=

!"#$%&'()

!=EsfablF=

!"#$%&'()*!+,-./kqp`= =m^i

!"#$%&'()*+,-./012

!"#

=^áJkbq=

!"#$%=^áJkbq=

!=S

!"#=^áJkbq=

!"#$%

!"#$%&'(

!"#$%&'()*+

Ai Std.

NTSC

PAL

NTSC

PAL

!"#$%&'&(

!"#$%&'()*+,%-./0)123456- %&789:

!"#$#%&'(

!"#$%&'()* +,-./01234)56

INSTALLATION/

L-Bracket Hole Application Chart/i=

!"#

Fig. 7

Fig. 8

Fig. 1

English

Preparation for playback

Before operating the unit, follow the procedure below for load-

ing the CD magazine.

1. To remove the CD tray

3 from the CD magazine, pull the

lever

2 with your finger (Fig. 1).

2. Insert one disc into each CD tray

3 of the magazine (up to 6

discs ). Make sure the label side of the disc is facing up (Fig. 2)

NOTE:

Hold the disc so you will not leave fingerprints on the disc

surface (refer to "PROPER CARE OF YOUR DISC" section).

When removing the CD tray from the CD magazine, hold the

tray securely so as not to drop the disc.

3. Insert each CD tray, with the disc loaded, all the way into the

CD magazine (Fig. 3).

Be sure to insert 6 CD trays whether the disc is loaded or not.

Make sure the CD trays are inserted straight to prevent jam-

ming (Fig. 4).

4. Open the CD magazine compartment door by sliding it to the

right until it locks. (Fig. 5)

5. Insert the CD magazine

1 all the way into the Shuttle until it

locks with the narrow side facing the unit as shown in Fig. 6.

6. After inserting the CD magazine

1, close the CD magazine

compartment door by sliding it to the left. (Fig. 7)

Caution: Door must be completely closed and remained closed

at all times to prevent dust, water and smoke contam-

inants from diminishing the overall performance of

the CD Shuttle.

7. To remove the CD magazine, open the CD magazine com-

partment door, then press the eject button

4. (Fig. 8)

Note: Do not forcibly remove the CD magazine by hand be-

cause this would cause damage to the changer

mechanism.

English

Installation of "L" type brackets

1. Determine the mounting location and angle.

2. Change the spring position to the mounting angle.

3. Mount the "L" type bracket according to the mounting angle.

Use the hexagon washer-head bolts (M4 x 8) to fasten the two

"L" type mounting brackets (supplied) to the sides of the CD

Shuttle.

NOTE: For the diagonal mounting, depending upon the mount-

ing angle choose the vertical bracket or horizontal brack-

et.

To mount the unit using Velcro tape:

When mounting the unit using Velcro tape, be sure to mount on

the flat location. Do not mount the unit upside down.

Handling CD magazine/

=`a=

Fig. 2

Installation of Shuttle to Vehicle Floor

Use the hexagon flange-head screws (M5 x15) to fasten the "L"

type mounting brackets (supplied) to the vehicle floor.

1Hexagon Flange-head Screws (M5 x 15)

2"L" Type Brackets (For Horizontal Mounting)

3"L" Type Brackets (For Vertical Mounting)

Using Floor Base Plates

1. Determine a mounting location by placing the Shuttle under

the carpet.

2. First, insert the Hexagon bolts (M6 x 25) up through the holes

in the bottom of the floor base plates. The bolt heads should

be recessed into the hole under the base plate so the base lays

flat on the floor. Then, mount the floor base plates to the floor

of the vehicle with the Hexagon flange-head screws (M5 x 15).

3. Cut mat in "+" shape with a knife to allow the threaded shaft

of the floor base plates to come through.

4. Mount the Shuttle on the carpet with hexagon flange-head

nuts (M6).

1Hexagon Flange-head Screws (M5 x 15)

2"L" Type Brackets (For Horizontal Mounting)

3"L" Type Brackets (For Vertical Mounting)

4Floor Base Plates

5Hexagon Flange-head Nuts (M6)

6Hexagon Bolts (M6 x 25)

Video CD Operation/s=`a=

ALPINE ELECTRONICS OF AMERICA, INC.

19145 Gramercy Place, Torrance,

California 90501, U.S.A.

Tel.: 1-800-ALPINE-1 (1-800-257-4631)

ALPINE ELECTRONICS FRANCE S.A.R.L.

(RCS PONTOISE B 338 101 280)

98, Rue De La Belle Etoile, Z.I. Paris Nord Il

B.P. 50016 F-95945, Roissy,

Charles De Gaulle Cedex, France

Tel.: 01-48 63 89 89

ALPINE ELECTRONICS, INC.

Tokyo office: 1-1-8 Nishi Gotanda,

Shinagawa-ku, Tokyo 141-8501, Japan

Tel.: (03) 3494-1101

ALPINE ITALIA S.p.A.

Via C. Colombo 8, 20090 Trezzano Sul

Naviglio MI, Italy

Tel.: 02-48 40 16 24

ALPINE ELECTRONICS OF CANADA, INC.

Suite 203, 7300 Warden Ave. Markham,

Ontario L3R 9Z6, Canada

Tel.: 1-800-ALPINE-1 (1-800-257-4631)

ALPINE ELECTRONICS OF U.K., LTD.

13 Tanners Drive, Blakelands,

Milton Keynes MK14 5BU, U.K.

Tel.: 01908-61 15 56

ALPINE ELECTRONICS OF AUSTRALIA PTY. LTD.

6-8 Fiveways Boulevarde Keysborough,

Victoria 3173, Australia

Tel.: (03) 9769-0000

ALPINE ELECTRONICS DE ESPAÑA, S.A.

Portal De Gamarra 36, Pabellón 32

01013 Vitoria (Alava)-Apdo. 133, Spain

Tel.: 34-45-283588

ALPINE ELECTRONICS GmbH

Kreuzerkamp 7-11

40878 Ratingen, Germany

Tel.: 02102-45 50

Under Rear Deck Installation

1. Attach the "L" type brackets to both sides of the Shuttle with

hexagon washer-head bolts (M4x8) .

2. Drill with approx. 6mm diameter tip and firmly mount brackets

with hexagon flange-head bolts (M6x 50) and hexagon flange-

head nuts (M6).

2"L" Type Brackets (For Horizontal Mounting)

5Hexagon Flange-head Nuts (M6)

7Hexagon Flange-head Bolts (M6 x 50)

8Hexagon Washer-head Bolts (M4 x 8)

Fig. 6

Fig. 5

Fig. 4

Fig. 3

English

Sampling Rate ................................................................................................................................................................ 44.1 kHz

System. ..................................................................................................................................... Optical (Compact disc System)

Number of Quantization Bits ................................................................................................................................. 16-bit Linear

Oversampling .................................................................................................................................................................. 8 Times

Number of Channels .................................................................................................................................................... 2 (stereo)

Frequency Response. ........................................................................................................................ 20-20,000 Hz (+0, -0.5 dB)

Wow & Flutter ..................................................................................................................................... Below measurable limits

Total Harmonic Distortion. ................................................................................................................................. 0.1% (at 1 kHz)

Signal-to-Noise Ratio. ...................................................................................................................................................... 80 dBA

Channel Separation ......................................................................................................................... More than 75 dB (at 1 kHz)

Power Requirement .................................................................................................................. 14.4 V DC (11 -16V allowable)

Output Voltage ........................................................................................................................................ 850 mV into 10 kohms

Weight. .......................................................................................................................................................... 1.8 kg (3 lbs. 15 oz)

Dimensions (H x W x D) ..................................................................................................................... 2-3/8" x 9-13/16" x 7-5/8"

...................................................................................................................................................................... (60 x 250 x 193 mm)

NOTE:

Due to product improvement, specifications and design are subject to change without notice.

Specisications/

Proper care of your disc/

!"#$%

English

Refer Fig. 1-4

1 Transparent Sheet

2 Disc Stabilizer

3 Center Hole

4 Bumps

Proper Handling (Fig. 1)

Handle your disc as shown. Do not drop the disc while handling. Hold the disc

so you will not leave fingerprints on the surface. If the surface is scratched, it

may cause the pickup to skip. Do not affix tape, paper, or gummed labels on

the disc. Do not write on the disc.

Keep Your Discs Clean (Fig. 2)

Fingerprints, dust, or soil on the surface could cause the pickup to skip. For

routine cleaning, wipe the playing surface with a clean, soft cloth from the

center of the disc to the outer edge. If the surface is heavily soiled, dampen a

clean, soft cloth in a solution of mild neutral detergent before cleaning the disc.

Disc Accessories (Fig. 3)

Various disc accessories for protecting the surface of the disc and improving

sound quality are available on the market.

However, many of them will increase the thickness and/or diameter of the disc.

Using such accessories may place the disc beyond the specified size limita-

tions and cause the changer to malfunction. Because of the high precision

electronics of the VPA-S001 and the highly stable mechanism, these accesso-

ries are not necessary and therefore not recommended for use with discs

placed in the VPA-S001.

Caution for new discs (Fig.4)

When a newly purchased disc is inserted into the changer magazine, the disc

may fail to play after initial loading. This is caused by small bumps around the

center hole and outside of the disc, which prevent stable loading into the

correct position. To remove the bumps, rub the inside edge of the hole and

outside edge of the disc with a ball-point pen or other such instrument, then

insert the disc again.

NOTE:

The mechanism automatically prevents this type of disc from playing as a

protective measure. This is not an indication of faulty operation.

Damaged Disc

Do not attempt to play cracked, warped, or otherwise damaged discs.

Playing a bad disc could severely damage the playback mechanism.

Storage

When not in use, place your discs in their individual cases and store them

in a cool place away from the sun, heat, and dust.

Irregular Shaped Discs (Fig. 5)

Make sure the discs you use in this unit do not have any irregularities. The

outer and inner edges should be round and smooth. Use of irregularly

shaped discs may cause damage to the mechanism.

Fig. 1

Fig. 4

Fig. 5

Fig. 3

Fig. 2

English

Discs that may be played on this unit should have the following marks on them.

Video CD

Audio CD

What is the Video CD?

The Video CD contains digital video data that is compressed using one of the international standards "MPEG 1" of digital

compression technology. Employing this compression technology, a 12cm disc can hold digital data of pictures for up

to 74 minutes (Max.) since the data is compressed down to 1/140. At the same time, digital audio data is compressed

down to 1/6 of conventional audio CD.

There are 2 versions for video CDs, Version 1.1 and version 2.0. The VPA-S001 can play both versions. It, however, does

not support the PBC (Playback Control) feature of Version 2.0.

Basic Operation

1. Settings on the Monitor

Set the Monitor to the external video input.

2. Operation of this unit

Operation of this unit (disc selection, playback, etc.) should be performed from the head unit. For details, refer to the

Owner's Manual for the head unit to be used.

3. Selecting vocal modes

Lightly press the VOCAL switch on the unit to select a desired vocal mode. Each press changes the modes as follows:

MOD1*

Notes: q *MOD1 Mode

When this mode is activated, the center position sound recorded in stereo on a video CD will be decreased.

If it was recorded in monaural, the whole sound will be decreased. When playing a music source or movie that

is recorded in monaural, the sound level may become low and it sounds like a noise. This is not a malfunction.

q Track Numbers of the Head Unit Displayed

When a video CD is played back, the unit first read the program data as a one track. The head unit, therefore,

displays one additional track number.

To User of CVA-1000E

When you play a video CD, follow the procedure described here.

1. Place the unit in the CHG (Changer) mode, then select the desired video CD.

2. Press the V.SEL (Video Select) button to activate the external input mode.

3. The picture of the video CD will be displayed on the screen.

Notes:

· Before starting operation of the disc selection, playback, fast forwarding, etc., be sure to place the unit in the

CHG mode.

· From the remote control supplied with the CVA-1000E, only the volume level can be controlled.

Digest Play Operation

1. Press and hole the VOCAL button attached to the unit for at least 2 seconds to start the Digest play.

2. The still pictures will be displayed one by one on the nine frame display screen.

3. To end the Digest play, press and hold the VOCAL switch again for at least 2 seconds.

Notes:

· During the Digest play, the sound will be momentarily interrupted.

· During the Digest play, the VOCAL mode cannot be selected.

Vertical/

Diagonal/

Horizontal/

Yes/

No/

Yes/

No/

Yes/

No/

Yes/

(For Vertical Mounting)

(For Horizontal

Mounting)

!"#$%

=i=

!"#$%&

!"#$%&'()

!"#$%=i=

!"#$%&'()*+jQ U

!=i

!"#$%&'()*=`a=

!"#

!"#$%&'"#()*+,-./012./

!"#$%&'()

!"#$%&'()*+,-.(/01234

!"#$%&

!"#$%&'(

!"#$%&'jR NR

=i=

!"#$%&'()*+,-

!"#$%jR NR

2i=

!"#$%&'(

3i=

!"#$%&'(

!"#$%&

!"#$%&jQ U

=i=

!"#$%&'(

=S=ãã=

!"#$%&'()*+,-.jS RM

!"#

!jS

!""#$

2i=

!"#$%&'(

!"#$%jS

!"#$%jS RM

!"#$%jQ U

!"#$%&'()*$+

!"#$%&jS OR

!"#$%&'(

!"#$%

!"#$%&'()*+(,-./(0

!"#$%&

!"#$%&' "(

!"#$%&'()*!+,-./0

!"#$%&jS

!"#$%&'(

!"#$%jR NR

2i=

!"#$%&'(

3i=

!"#$%&'(

!"#$%jS

!"jS OR

!"#

!"#$%=`a=

=`a=

!" O

!"=`a=

!"#$%&

!"=S=

!"#

!"#$%&'(

!"#$%&'

`a=

=`a=

!"#$%&'()

!"#$%&=`a=

!"#=`a=

!"#$

!=S= =`a=

`a=

!"#$%&'()*

QK `a=

!"#$%&'()*+,

=`a=

!"#$%&'()

=`a=

!"#$%

!"#$%&

!"#$%&'

!"#$%=`a=

!"#

!=`a=

=`a=

!"#$%& Q

!"#$%=`a=

!"#$%$&'(

KKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKK QQKN=heò

KKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKK

! KKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKK

=NS=

! KKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKK OM OMMMM=eò

MKR=Ç_

KKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKK

!"#

!" KKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKK MKN

N=âeò=

! KKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKK

=TR=Ç_

N=âeò=

! KKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKK

=NQKQ=s

NS=s=

!"#"$% KKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKK SM ORM NVP=ãã

!"#$%&'()*+,-./01

=NJQ

!"#

!"#=N

!"#$%

!"#$

!"#$%&'

()*

!"#$%&'()*+,-.

!"#$%&'%!()*+,

!"#$

!"#$%=O

!"#$%&'()*+,-./012

!"#$%&'()*+

!"#$%&

!"#$%&'()*+,-./01234562

!"#=P

!"#$%&'()*+,-./01&'23

!"#$%&'()*+,-./012345$%672)*89:;+

!"#$%&'()*+, sm^JpMMN=

!"#$%&'()!#*

!"#$%&'()*+,$-./=sm^JMMN=

!"#$%&'(

!"#$%&=Q

!"#$%!&"'()*+,$-!"./0123)4567!"89

!"#$%&&'()*+,-./0123'45

!"#$%&

!"#$%&'()*+,-./012.34567801

!"#$%&'()*+,-./(0123

!"#$%&

!"#$%&'()*+,$-./0123

!"#$%&'()

!"#$%&'()*+,-./'012345678*9:;<

!"#$%&'=R

!"#$%&'()*+,-./

!"#$%&

!"#

!"#$%&'(

!"#$%&'"()*+,'-./

sáÇÉç=`a

^ìÇáç=`a

=s=`a

s=`a=

!"# $%&'() !*+,-./012334=jmbdN

!"#$%&'()*"#+,=NL

NQM

=NO=Åã=

!"#$%&'(=TQ=

!"#$#%

!"#$!%&'()*#$=`a= =NLS

!=`a=

NKN=

=OKM=

sm^JpMMN=

!"#$%&'()*+,-=OKM=

=m_`

!"#$%

!"#$%&'()*+

!"#$%&'()*+,-.!/012

!"#$%&'!()!*+,-

!"#

!"=sl`^i=

!"#$%&'(

MOD1*

jla=N

!"#$%s=`a=

!"#$%&'()*+",-./0

!"#$%&'(")*+,-

!"#$%&'()*+,-#./01234567+8#

!"#$%&

=s=`a=

!"#$%&'()*+,-

!"#$%&'()*+,-.

=`s^JNMMMb=

!=s=`a=

!"#$%&

!"!#=`ed

!"#$%&

=sKpbi

!"#

!"#$%&

!"#$=s=`a=

!"#$%&

!"#$%

!"#"$=`ed=

!=`s^JNMMMb=

!"#$%"&'(

!"#$%

!"#$%=sl`^i= =O=

!"#$%&

!"#$%&'=V=

!"#$%&'()*=sl`^i= =O=

!"#$%&'()*+,-.

!"#$%&'()*=sl`^i=