ALPINE TMEM750 - Owner's Manual Immediate Download

TME-M750

6.5-inch Mobile Color Monitor

68P21523Y50-O

Printed in Japan (S)

Read this manual carefully before starting operation and use this system safely. We cannot be responsible for

problems resulting from failure to observe the instructions in this manual.

This manual uses various pictorial displays to show how to use this product safely and to avoid harm to yourself and

others and damage to your property. Here is what these pictorial displays mean. Understanding them is important

for reading this manual.

Meaning of displays

Points to Observe for Safe Usage

This label is intended to alert the user to the presence of important operating instructions.

Failure to heed the instructions will result in severe injury or death.

This label is intended to alert the user to the presence of important operating instructions.

Failure to heed the instructions can result in injury or material damage.

Caution

Warning

DO NOT DISASSEMBLE OR ALTER. Doing so may lead to accident, fire or electric shock.

KEEP SMALL ARTICLES OUT OF THE REACH OF CHILDREN. If swallowed, consult a physician immediately.

USE THE CORRECT AMPERE RATING WHEN REPLACING FUSES. Failure to do so may result in fire or electric

shock.

USE ONLY IN VEHICLES WITH A 12 VOLT NEGATIVE () GROUND. Check with your dealer if you are not sure.

Failure to do so may result in fire or electric shock.

BEFORE WIRING, DISCONNECT THE CABLE FROM THE NEGATIVE () BATTERY TERMINAL. Failure to do so

may result in electric shock or injury due to electrical shorts.

DO NOT CUT AWAY THE WIRE SHEATH AND USE POWER FOR OTHER EQUIPMENT. Doing so may exceed the

current carrying capacity of the wire and result in fire or electric shock.

DO NOT INSTALL IN LOCATIONS WHICH MIGHT HINDER VEHICLE OPERATION OR CREATE HAZARDS FOR

VEHICLE OCCUPANTS. Doing so may obstruct forward vision or hamper movement.

DO NOT CONTACT, DAMAGE OR OBSTRUCT PIPES, FLUID LINES OR WIRING WHEN DRILLING HOLES. Failure

to take such precautions may result in fire or cause an accident or injuries.

DO NOT USE NUTS OR BOLTS IN THE BRAKE SYSTEM WHEN MAKING INSTALLATION OR GROUND

CONNECTIONS. Never use safety-related parts such as bolts or nuts in the steering or brake systems or tanks to make

wiring installations or ground connections. Using such parts could disable control of the vehicle and cause brake failure,

other accident or injury.

HALT USE IMMEDIATELY IF A PROBLEM APPEARS. When problems occur such as a lack of sound or video, foreign

objects inside the unit, smoke coming out, or noxious odors, stop use immediately and contact the dealer where you

bought the equipment. Failure to do so may result in an accident or injury.

DO NOT OPERATE THE EQUIPMENT OR LOOK AT THE SCREEN WHILE DRIVING THE VEHICLE. Operating the

equipment may distract the driver from looking ahead of the vehicle and cause accident. Always stop the vehicle in a

safe location before operating this equipment.

DO NOT INSTALL THE MONITOR NEAR THE PASSENGER SEAT AIR BAG. Ensure that the location chosen for the

monitor does not interfere with the operation of the passenger seat air bag. This will prevent the triggered air bag from

launching the display towards passengers, possible causing injury.

MAKE THE CORRECT CONNECTIONS. Failure to do so may cause fire or accident to occur.

ARRANGE THE WIRING SO IT IS NOT CRIMPED OR PINCHED. Route the cables and wiring so as not to be crimped

by moving parts or make contact with sharp or pointed spots which might damage the wiring. Failure to do so may cause

failure of unit or vehicle.

DO NOT RAISE THE VOLUME EXCESSIVELY. Keep the volume at a level where you can still hear outside noises

while driving. Driving while unable to hear outside noises could be the cause of accident.

DO NOT USE THIS EQUIPMENT FOR PURPOSES OTHER THAN STATED FOR THE VEHICLE. Failure to do so may

result in electric shock or injury.

HAVE THE WIRING AND INSTALLATION DONE BY EXPERTS. The wiring and installation of this unit requires special

technical skill and experience. To ensure safety, always contact the dealer where you purchased this unit to have the

work done.

WIDE COLOR LCD MONITOR

POWER

VOLUME

SELECT

TME-M750

s OWNER'S MANUAL

· Please read before using this equipment.

TV TUNER INPUT

PHONE OUTPUT

VIDEO

AUDIO

AUX INPUT 2

MOBILE COLOR MONITOR

TME-M750

NAVIGATION INPUT

DISPLAY OUTPUT

POWER SUPPLY

VIDEO

AUDIO

AUX INPUT 1

12 3

WIDE COLOR LCD MONITOR

POWER

VOLUME

SELECT

TME-M750

English

USE SPECIFIED ACCESSORY PARTS AND INSTALL THEM SECURELY. Be sure to use only the specified

accessory parts. Use of other than designated parts may damage this unit internally or may not securely install the unit in

place as parts that come loose can create hazards.

DO NOT INSTALL IN LOCATIONS WITH HIGH MOISTURE OR DUST. Avoid installing the unit in locations with high

incidence of moisture or dust. Moisture or dust that penetrates into this unit may cause smoke or fire.

Caution

Monitor

1 POWER button

2 DOWN (

) button

3 UP (

) button

4 SELECT button

Notes:

This unit will automatically detect the NTSC and PAL video standards.

In the PAL mode, characters may freeze or banding may occur in some images. Make sure you have selected the

correct video mode for your system.

Screen Display ON/OFF

Press the POWER button.

To turn off the POWER, press the POWER button again.

Notes:

· If properly connected, the monitors main POWER will turn off when the vehicle's ignition switch is off. If the main

power lamp illuminates in the STAND BY mode, the vehicle's battery may be discharged.

· On Screen Display

Operating the monitor functions will be displayed On Screen for 3 seconds.

Adjusting the Volume

Adjust the volume level by pressing the DOWN (

) or UP (

) button.

Mode switching

Press the SELECT button. Each press of the button will cycle through the modes as follows:

Adjustment

Press and hold the SELECT button for at least 1 second.

Each press of the button will cycle through the modes as follows:

Adjust by pressing the DOWN (

) or UP (

) button.

· BRIGHT: Adjust the brightness of the picture.

· COLOR: Change the color balance of the picture.

Note: The color adjustment is disabled when using the RGB connection or if TV mode selected.

· TINT: Adjust the tint of the picture.

Note: The color adjustment is disabled when using the RGB connection or if TV mode selected.

· DIMMER:

AUTO: Backlighting of the monitor adjusts automatically to the ambient light available inside the vehicle.

LOW: Backlighting is set to its lowest level.

MAX: Backlighting is set to its maximum level.

· DIMMER LEVEL: Adjust the backlighting output level.

· DISPLAY MODE:

WIDE: Expands a normal broadcast picture to fit the entire screen.

CINEMA: Displays a widescreen formatted picture (16:9) to fit the entire screen.

ZOOM: Displays a normal broadcast picture to fit the entire screen by cropping the left and right video information.

NORMAL: Displays a normal broadcast picture without modification. Black stripes will appear at left and right of the

screen.

· SOUND OUT

MONITOR: Outputs sound through the built-in speakers.

HEADPHONES: Outputs sound to headphones if connected.

After completing adjustments, press and hold the SELECT button for at least 1 sec.

Notes:

After turning the system off, a slight ghost of the image will remain temporarily. This is an effect peculiar to LCD

technology and is normal.

Under cold temperature conditions, the screen may lose contrast temporarily. After a short warm-up period, it will

return to normal.

It is normal for a very small number of the screen's pixels to be off. Even under the very high precision manufacturing

conditions, this fact is unavoidable.

NAVIGATION

AUX1

AUX2

NAVIGATION

BRIGHT

COLOR

TINT

DIMMER

DIMMER LEVEL

DISPLAY MODE

SOUND OUT

BRIGHT

In Case of Difficulty

ALPINE ELECTRONICS, INC.

Tokyo office: 1-1-8 Nishi Gotanda,

Shinagawa-ku, Tokyo 141-8501, Japan

Tel.: (03) 3494-1101

ALPINE ELECTRONICS OF AMERICA, INC.

19145 Gramercy Place, Torrance,

California 90501, U.S.A.

Tel.: 1-800-ALPINE-1 (1-800-257-4631)

ALPINE ELECTRONICS OF CANADA, INC.

Suite 203, 7300 Warden Ave. Markham,

Ontario L3R 9Z6, Canada

Tel.: 1-800-ALPINE-1 (1-800-257-4631)

ALPINE ELECTRONICS OF AUSTRALIA PTY. LTD.

6-8 Fiveways Boulevarde Keysborough,

Victoria 3173, Australia

Tel.: (03) 9769-0000

ALPINE ELECTRONICS GmbH

Kreuzerkamp 7-11 40878 Ratingen,

Germany

Tel.: 02102-45 50

ALPINE ITALIA S.p.A.

Via C. Colombo 8, 20090 Trezzano Sul

Naviglio MI, Italy

Tel.: 02-48 40 16 24

ALPINE ELECTRONICS FRANCE S.A.R.L.

(RCS PONTOISE B 338 101 280)

98, Rue De La Belle Etoile, Z.I. Paris Nord II

B.P. 50016 F-95945, Roissy,

Charles de Gaulle Cedex, France

Tel.: 01-48 63 89 89

ALPINE ELECTRONICS OF U. K., LTD.

13 Tanners Drive, Blakelands,

Milton Keynes MK14 5BU, U.K.

Tel.: 01908-61 15 56

ALPINE ELECTRONICS DE ESPAÑA, S.A.

Portal De Gamarra 36, Pabellón 32

01013 Vitoria (Alava) - Apdo. 133, Spain

Tel.: 34-45-283588

Adjusting the Volume

POWER

Mode switching

SELECT

Adjustment

Screen Display ON/OFF

Cause

Car's ignition is off.

No fuse or blown fuse.

Incorrect connections.

Vehicle's battery is weak.

Fluorescent tube is exhausted.

Brightness control is set for

minimum brightness control.

Incorrect setting of the VCR mode.

Protective circuit is on because of

high temperature.

Incorrect or open connection with

the Monitor, AV Interface unit.

Brightness/Colour/Tint control are

not set to the proper positions.

Caused by neon signs, high-voltage

power lines, CB transmitter, other

vehicle's ignition plugs, etc.

Symptom

No function or

display.

Unclear picture

display.

No picture

display.

Picture colour is

poor.

Spots or dotted

lines/stripes

appear.

Solution

Turn the ignition on.

Check the cause and replace the fuse.

Check connection and remedy.

Check the voltage of vehicle's battery.

Replace the fluorescent tube*.

Adjust the brightness.

Switch to the correct mode.

Wait until the temperature inside the vehicle comes down to

the operating temperature range (45

°C).

Check the connection and remedy.

Check each control.

Change the location of your vehicle.

The fluorescent tube replacement is not free of charge even within the warranty period, for the tube is an article of

consumption.

NAVIGATION

AUX1

AUX2

NAVIGATION

BRIGHT

COLOR

TINT

DIMMER

DIMMER LEVEL

DISPLAY MODE

SOUND OUT

BRIGHT

Operation

Parts Identification

(RCS PONTOISE B 338 101 280)

Sankei Kikaku Co., Ltd.

1-13-38, Hinodai,

Hino, Tokyo, Japan

If you encounter a problem, please review the item in the following check list. This guide will help you isolate the problem

if the unit is at fault. Otherwise, make sure the rest of your system is properly connected or consult your authorized

Alpine dealer.

English

RIN

UTPU

VID

DIO

AUX

INPUT

MOBILE

COLOR

MONITOR

TME-M750

VIG

ATIO

NIN

DISPLAY

OUTPUT

POW

SUPPLY

VID

DIO

AUX

INPUT

TV TUNER INPUT

PHONE OUTPUT

VIDEO

AUDIO

AUX INPUT 2

MOBILE COLOR MONITOR

TME-M750

NAVIGATION INPUT

DISPLAY OUTPUT

POWER SUPPLY

VIDEO

AUDIO

AUX INPUT 1

WIDE COLOR LCD MONITOR

POWER

VOLUME

SELECT

TME-M750

Installing the Monitor

Caution:

Do not install the monitor near the air bag system in front passenger's seat.

Assemble the supplied bracket and mount the monitor temporarily.

Note:

Always use the supplied bracket or equivalent.

Verify the installation location.

Select a flat surface and temporarily mount the unit. Use adhesive tape, etc.

Notes:

· Mounting hints

· Top of the monitor does not exceed the top of the dash when viewed from the driver's seat.

· Mounting surface is stable.

· Monitor can be angled for easy viewing.

· In a vehicle with a front passenger air bag, do not install the unit where it will interfere with the

operation of the system.

· If the surface of the dash board is finished with other than plastic (true leather, wooden panel, cloth

covered panel, etc.), there will be some damage if the bracket is removed.

Remove the monitor from the bracket.

Peel the protective paper from the double-stick tape on bracket's base.

Clean the mounting location with the cleaner supplied.

Notes:

· Warm the mounting location with a dryer, etc. and then place the bracket into position.

· Do not apply force or moisture for 24 hours after installation.

· If the bracket is not attached securely with just the tape, use the supplied screws to complete the

installation.

· 5: If the mounting surface is curved slightly, reform the base to fit to its shape.

Connect the monitor and the AV Interface unit.

Insert the connector of the AV Interface Unit into the AV Interface connector of the monitor until a click

is heard.

Mount the monitor on the bracket.

Slide the mounting foot into the bracket on the monitor. Secure the monitor by tightening the locking

collar.

Dress the monitor's cable using the cord clamp provided.

Adjust the height and angle of the monitor for easy visibility.

Determine the height and angle. Tighten the height and angle adjusting screws to secure the monitor.

Numbers Identification

1 Mounting Bracket

2 Monitor

3 Dashboard

4 Double-stick Tape

5 Mounting Screws (Included)

6 AV Interface Unit

7 AV Interface Unit Connector Terminal

8 AV Interface Unit Connector

9 Cord Clamp

p Height Adjustment Screw

q Angle Adjustment Screw

Installing AV Interface Unit

This Unit can be placed inside the trunk, on the kick panel of the front passenger's seat or underdash.

However, to avoid unnecessary signal wiring, it is better to mount the Unit as close as possible to the

Display.

DO NOT MOUNT THE UNIT IN LOCATIONS THAT WILL BE IN THE VICINITY OF MOISTURE OR

EXTREME HEAT (such as the engine compartment).

VelcroTM Tape Mounting:

This installation method is suggested when the mounting location does not permit drilling.

USE THIS METHOD ONLY WHEN THE UNIT IS MOUNTED ON A HORIZONTAL SURFACE. NEVER

MOUNT A UNIT UPSIDE-DOWN USING THE VELCROTM TAPE.

1. Remove the adhesive protective paper from one side of the VelcroTM tape.

2. Attach the exposed adhesive side to the underside of the Unit, in a central location. Do not cover the

serial number.

3. Make sure the mounting location is clean, dry and free from contaminants.

4. Remove the protective strip from the other side of the VelcroTM pad.

5. Press the unit onto its mounting location.

Numbers Identification

1 Floor/Trunk

2 VelcroTM Tape (Included)

3 Press onto the carpet.

Installation

Please read the Owner's Manual of the products connected also.

1 TV tuner

Alpine TV tuner

2 Navigation

Alpine Navigation system

3 To RGB Output connector

Connect to the RGB output connector of the Alpine navigation system.

4 DVD player

Alpine DVD player

5 To Video Output Connector

Connect to the Video Output Connector of the Alpine DVD player.

6 Video

7 To Audio Output Terminal (R)

8 To Audio Output Terminal (L)

9 To Video Output Terminal

p Headphones

Cautions

Make connections correctly.

Improper connections may cause a fire or operation failure.

Parking brake lead (Yellow/Blue)

Connect this lead to the parking brake lead powered when parking brake is pulled.

Remote control output lead (White/Brown)

To remote control input lead of ALPINE product used in combination.

ACC power lead (Red)

To ACC power lead powered when engine key position is ACC.

Fuse (5A)

Ground lead (Black)

Connect the lead to a good chassis ground on the vehicle. Make sure the connection is made to bare

metal and is securely fastened using the sheet metal screw provided.

Brake Lead

Brake Connector (Included)

Brake Lamp

Brake Signal Lead

Brake Switch

Connections

Monitor

AV-Interface Unit

Power Lead Connection

System Connection

MONITOR

Screen Size ...................................................................................................................................... 6.5-type

Display System ................................................... Low reflection rear projection type TN liquid crystal panel

Drive System ............................................................................... Active matrix drive, normally white display

Number of Picture Elements ................................................................ 336, 960 pcs. (H:1440 x V:234 dots)

Light Source ................................................. Internal optical system (U-type cold cathode fluorescent tube)

Dimensions (W x H x D) ............................................................................................. 178 x 124.8 x 32.1mm

Weight ................................................................................................................................................... 470g

AV Interface Unit

Dimensions (W x H x D) .......................................................................................... 196.2 x 119.9 x 28.5mm

Weight ................................................................................................................................................... 670g

Specifications