WARNING
To prevent fire or shock hazard, do not
expose this appliance to rain or moisture.
Operator's Manual
s5000/s6000
STEREO DIGITAL SAMPLER
Software version V1.21
09/22/2000 Rev.4
The lightning flash with arrowhead symbol , within an equilateral triangle, is
intended to alert the user to the presence of uninsulated "dangerous voltage"
within the product's enclosure; that may be of sufficient magnitude to
constitute a risk of electric shock to persons.
The exclamation point within an equilateral triangle is intented to alert the user
to the presence of important operating and maintenance (servicing) instruc-
tions in the literature accompanying the appliance.
THE SYMBOLS ARE RULED BY UL STANDARDS (U.S.A.)
5B-En
WARNING!!
To prevent fire or shock hazard, do not expose this appliance to rain or moisture.
1-En
CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK
DO NOT REMOVE COVER (OR BACK).
NO USER-SERVICEABLE PARTS INSIDE.
REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.
CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN
Lithium battery
This product uses a lithium battery for memory backup.
The lithium battery should only be replaced by qualified service personnel.
Improper handling may cause risk of explosion.
24A-En
Important Notice
The material in this document is copyright to AKAI professional M.I. Corp., and may not be
quoted or reproduced in any form without written permission from the company.
LIMITED SOFTWARE WARRANTY POLICY
All the software provided with, or purchased especially for, AKAI professional products has
been tested for functionality. AKAI professional M.I. Corp. will make its best efforts to correct
reported software defects for future releases subject to technical practicabilities.
AKAI professional M.I. Corp. makes no warranty or representation either expressed or
implied with respect to the system's performance or fitness for a particular purpose.
In no event will AKAI professional M.I. Corp. be liable for direct or indirect damages arising
from any defect in the software or its documentation. Further, AKAI professional M.I. Corp.
will not accept any liability for any programs, sounds, audio recording or sequences stored in
or used with AKAI professional products, including the cost of recovery of such data.
The warranties, remedies and disclaimers above are exclusive and take precedence over all
others, oral or written, express or implied, to the extent permitted by law in the geographical
area of the product's use. No employee of AKAI professional M.I. Corp., agent, distributor or
employee of an agent or distributor is authorised to offer any variation from this policy.
Version 1.21
i
s5000/ s6000
WARNING
WARNING: WHEN USING ELECTRIC PRODUCTS, BASIC PRECAUTIONS SHOULD ALWAYS
BE FOLLOWED, INCLUDING THE FOLLOWING:
WARNING
The S5000/S6000 is designed to be used in a standard household environment.
Power requirements for electrical equipment vary from area to area. Please ensure that your S5000/
S6000 meets the power requirements in your area. If in doubt, consult a qualified electrician or AKAI
professional dealer.
120 VAC
@ 60 Hz for USA and Canada
220~240 VAC
@ 50 Hz for Europe
240 VAC
@ 50 Hz for Australia
PROTECTING YOURSELF AND THE S5000/S6000
·
Never touch the AC plug with wet hands.
·
Always disconnect the S5000/S6000 from the power supply by pulling on the plug, not the
cord.
·
Allow only an AKAI professional dealer or qualified professional engineer to repair or reassemble
the S5000/S6000. Apart from voiding the warranty, unauthorized engineers might touch live
internal parts and receive a serious electrical shock. There are no serviceable parts inside.
·
Do not put, or allow anyone to put any object, especially metal objects, into the S5000/S6000.
·
Use only a household AC power supply. Never use a DC power supply.
·
If water or any other liquid is spilled into or onto the S5000/S6000, disconnect the power, and
call your dealer.
·
Make sure that the unit is well-ventilated, and away from direct sunlight.
·
To avoid damage to internal circuitry, as well as the external finish, keep the S5000/S6000
away from sources of direct heat (stoves, radiators, etc.).
·
Avoid using aerosol insecticides, etc. near the S5000/S6000. They may damage the surface,
and may ignite.
·
Do not use denatured alcohol, thinner or similar chemicals to clean the S5000/S6000. They will
damage the finish.
·
Modification of this equipment is dangerous, and can result in the functions of the S5000/
S6000 being impaired. Never attempt to modify the equipment in any way.
·
Make sure that the S5000/S6000 is always well-supported when in use (either in a specially-
designed equipment rack, or on a firm level surface).
·
When installing the S5000/S6000 in a 19" rack system, always allow 1U of ventilated free
space above it to allow for cooling. Make sure that the back of the rack is unobstructed to allow
a clear airflow.
·
In order to assure optimum performance of your S5000/S6000, select the setup location carefully,
and make sure the equipment is used properly. Avoid setting up the S5000/S6000 in the following
locations:
1. In a humid or dusty environment
2. In a room with poor ventilation
3. On a surface which is not horizontal
4. Inside a vehicle such as a car, where it will be subject to vibration
5. In an extremely hot or cold environment
ii
Version 1.21
WARNING
s5000/ s6000
WARNING
THIS APPARATUS MUST BE EARTHED
IMPORTANT
This equipment is fitted with an approved non-rewireable UK mains plug.
To change the fuse in this type of plug proceed as follows:
1) Remove the fuse cover and old fuse.
2) Fit a new fuse which should be a BS1362 5 Amp A.S.T.A or BSI approved type.
3) Refit the fuse cover.
If the AC mains plug fitted to the lead supplied with this equipment is not suitable for your type of
AC outlet sockets, it should be changed to an AC mains lead, complete with moulded plug, to the
appropriate type. If this is not possible, the plug should be cut off and a correct one fitted to suit the
AC outlet. This should be fused at 5 Amps.
If a plug without a fuse is used, the fuse at the distribution board should NOT BE GREATER than
5 Amp.
PLEASE NOTE:
THE SEVERED PLUG MUST BE DESTROYED TO AVOID A POSSIBLE
SHOCK HAZARD SHOULD IT BE INSERTED INTO A 13 AMP SOCKET
ELSEWHERE.
The wires in this mains lead are coloured in accordance with the following code:
GREEN and YELLOW
-- Earth
BLUE
-- Neutral
BROWN
-- Live
As the colours of the wires in the mains lead of this apparatus may not correspond with the coloured
markings identifying the terminals in your plug, please proceed as follows:
The wire which is coloured GREEN and YELLOW must be connected to the terminal which is
marked with the letter E or with the safety earth symbol
or coloured GREEN or coloured
GREEN and YELLOW.
The wire which is coloured BLUE must be connected to the terminal which is marked with the
letter N or coloured BLACK.
The wire which is coloured BROWN must be connected to the terminal which is marked
with the etter L or coloured RED.
THIS APPARATUS MUST BE EARTHED
Ensure that all the terminals are securely tightened and no loose strands of wire exist.
Before replacing the plug cover, make certain the cord grip is clamped over the outer sheath of the
lead and not simply over the wires.
6D-En
Version 1.21
iii
s5000/ s6000
WARNING
FCC WARNING
This equipment has been tested and found to comply with the limits for a Class B digital device
pursuant to Part 15 of the FCC rules. These limits are designed to provide reasonable protection
against harmful interference in a residential installation. This equipment generates, uses, and
can radiate radio frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications. However, there is no
guarantee that interference will not occur in a particular installation. If this equipment does
cause harmful interference to radio or television reception, which can be determined by turning
the equipment off and on, the user is encouraged to try to correct the interference by one or
more of the following measures:
·
Reorient or relocate the receiving antenna.
·
Increase the separation between the equipment and receiver.
·
Connect the equipment into an outlet on a circuit different from that to which the receiver is
connected.
·
Consult the dealer or an experienced radio/TV technician for help.
21B-En
AVIS POUR LES ACHETEURS CANADIENS DU S5000/S6000
Le présent appareil numérique n'ément pas de bruits radioélectriques dépassant les limites
applicables aux appareils numériques de la Class B prescrites dans le Règlement sur le
brouillage radioélectrique édicté par le ministère des Communications du Canada.
27-F
This digital apparatus does not exceed the Class B limits for radio noise emissions from digital
apparatus set out in the Radio Interference Regulations of the Canadian Department of
Communications.
27-En
VENTILATION
Do not prevent the unit's ventilation, especially by placing the unit on the soft carpet, in a
narrow space, or by placing objects on the unit's chassis--top, side, or rear panels. Always
keep the unit's chassis at least 10 centimeters from any other objects.
31C-En
CHANGES OR MODIFICATIONS NOT EXPRESSLY APPROVED BY THE MANUFACTURER
FOR COMPLIANCE COULD VOID THE USER'S AUTHORITY TO OPERATE THE
EQUIPMENT.
32-En
COPYRIGHT NOTICE
The AKAI S5000/S6000 is a computer-based device, and as such contains and uses software in
ROMs. This software, and all related documentation, including this Operator's Manual, contain
proprietary information which is protected by copyright laws. All rights are reserved. No part of
the software or its documentation may be copied, transferred or modified. You may not modify,
adapt, translate, lease, distribute, resell for profit or create derivative works based on the software
and its related documentation or any part there of without prior written consent from AKAI
professional M.I. Corp., Yokohama, Japan.