AIWA XP-SR320 - Owner's Manual Immediate Download

Highlighted letters in the text of this manual correspond to the illustrations.

PRECAUTIONS

To maintain good performance

· Do not use the unit in places which are extremely hot, cold, dusty or humid. In

particular, do not use or keep the unit in following places.

· in a high humidity area such as a bathroom

· near a heater

· in an area exposed to direct sunlight (e.g., inside a parked car, where it can

become extremely hot)

· near sources of strong magnetism, such as televisions, speakers, or magnets

· where there is a lot of movement or vibration, such as on a car dashboard or

an unstable shelf

· Do not open the battery compartment with wet hands.

· Wipe the unit thoroughly before inserting batteries and after use.

· Do not soak the unit in water.

For safety

· Do not attempt to disassemble the unit. Laser rays from the optical pickup are

dangerous to the eyes.

· Make sure that pins or other foreign object do not get inside the player.

· Take care not to drop the unit or subject it to strong shocks.

· To keep dust from the pickup lens, keep the disc compartment lid closed after

use. Never touch the lens.

· If you hear no sound when playing a disc, DO NOT turn the volume up high

because music could suddenly start at high volume. Turn the volume control to

the lowest level before starting playback and slowly turn it up to the desired level.

Note on listening with the headphones

· Listen at moderate volumes to avoid hearing damage.

· Do not wear the headphones while driving or cycling. It may create a traffic

hazard.

· You should use extreme caution or temporarily discontinue use in potentially

hazardous situations, such as walking, jogging, etc.

· Wear them properly; L is left, R is right.

Note on condensation

If the unit is suddenly moved from a cold place to a warm one, it may result in

condensation on the pickup lens and malfunction or playback difficulties.

Should this occur, leave the unit for a few hours, then try to playback again.

MAINTENANCE

To clean the lens

If the lens becomes dirty, the player will skip or not play. If this occurs, clean the

lens in the following manner.

To remove dust or dry particles, first use a camera lens blower/brush a to blow

a few times to loosen particles, then gently brush the lens b clean. Finish by

blowing the lens again.

To remove fingerprints, use a cotton swab dipped in lens cleaning solution. Wipe

gently from the center to the edge. Lens cleaning solution is commercially available.

Note

Take care not to get too much solution on the swab, which could flow into the unit

and cause damage.

Pressing too strongly with the swab could scratch or break the lens.

To clean the discs

Before playing, wipe the disc from the center outward with a cleaning cloth. After

playing, store the disc in its case.

SPECIFICATIONS

Tracking system

3-beam laser

Laser pickup

Semiconductor laser

D/A conversion

4-times oversampling digital filter + 1-bit DAC

Frequency response

20 20,000 Hz

Output

PHONES/LINE OUT jack (stereo mini-jack)

Frequency range

AM: 530/531 kHz 1,710/1,602 kHz

(10 kHz/9 kHz steps)

FM: 87.5 108 MHz

Maximum output

12 mW + 12 mW (16 ohms at 1 kHz)

500 mV (47 k ohms at 1 kHz)

Power supply

DC 3 V using two size AA (LR6) alkaline

batteries

DC 2.4 V using two commercially available

(Ni-Cd 1.2 V 700 mAh) rechargeable batteries

AC house current using the supplied AC adaptor

Maximum outside dimensions

134 (W)

× 32.5 (H) × 141 (D) mm

(excluding projecting parts and controls)

(5 3/8

× 1 5/16 × 5 5/8 in.)

Weight

Approx. 294 g (10.3 oz.) excluding batteries

Accessories

AC adaptor AC-D603 (1)

Stereo headphones (1)

Carrying case (XP-SR321 only) (1)

AC adaptor AC-D603U

Rated input: AC 120 V, 60 Hz

The specifications and external appearance of this unit are subject to change

without notice.

XP-SR321/XP-SR320

COMPACT DISC PLAYER

OPERATING INSTRUCTIONS

8B-HCD-901-01

010205AYG-O9

Printed in Indonesia

OWNER'S RECORD

For your convenience, record the model number and the serial number

(you will find it on the bottom of your set) in the space provided below.

Please refer to them when you contact your Aiwa dealer in case of difficulty.

Model No.

Serial No.

NOTE

FOR USE IN THE U.S.A.

This equipment has been tested and found to comply with the limits for a

Class B digital device, pursuant to Part 15 of the FCC Rules. These limits

are designed to provide reasonable protection against harmful interference

in a residential installation.

This equipment generates, uses, and can radiate radio frequency energy

and, if not installed and used in accordance with the instructions, may

cause harmful interference to radio communications. However, there is no

guarantee that interference will not occur in a particular installation. If this

equipment does cause harmful interference to radio or television reception,

which can be determined by turning the equipment off and on, the user is

encouraged to try to correct the interference by one or more of the following

measures:

Reorient or relocate the receiving antenna.

Increase the separation between the equipment and receiver.

Connect the equipment into an outlet on circuit different from that to

which the receiver is connected.

Consult the dealer or an experienced radio/TV technician for help.

CAUTION

Modifications or adjustments to this product, which are not expressly

approved by the manufacturer, may void the user's right or authority to

operate this product.

Stereo headphones (1)

Carrying case (XP-SR321 only) (1)

AC adaptor AC-D603U

Rated input: AC 120 V, 60 Hz

The specifications and external appearance of this unit are subject to change

without notice.

USING ON DRY CELL BATTERIES

1 Set the dial to the OPEN position to open the disc compartment, then

open the battery compartment.

2 Insert two size AA (LR6) alkaline batteries with the

0 and 9 marks

correctly aligned. After batteries insertion, close the battery compartment

firmly.

3 Close the disc compartment tightly and set the dial to the LOCK position.

Battery replacement

The battery indicator in the display changes from

according

to the remaining power of the batteries. Replace the batteries when

lights.

If the unit remains in use after

lights, "Lo-bAtt" appears and operation stops.

To maintain preset data

When replacing the batteries, the unit will retain the preset station frequencies

for about 1 minute. To prevent the erasure of the memories, replace the batteries

within 1 minute.

· Before replacing the batteries, turn off the power by pressing

sSTOP/OFF/CHARGE.

· DO NOT press any keys while replacing the batteries, otherwise it will not

retain preset data for 1 minute.

Battery life (using alkaline batteries LR6)

Battery life may vary depending on conditions of use.

If the cover of the battery compartment comes off

Note

Close the battery compartment firmly, or the compact disc may be

damaged.

Note on dry cell batteries

· Make sure that the

0 and 9 marks are correctly aligned.

· Do not mix the different types of batteries, or an old battery with a new one.

· To prevent the risk of electrolyte leakage or explosions, never recharge the

batteries, apply heat to them, or take them apart.

· When not using the batteries, remove them to prevent needless battery wear.

· If liquid leaks from the batteries, wipe thoroughly to remove.

The setting of the E·A·S·S switch

Battery life

Approx. 27 hours

12 or OFF

Approx. 19 hours

XP-SR321/SR320(AU)E

USING ON RECHARGEABLE BATTERIES

· Be sure to use size AA Ni-Cd 1.2 V 700 mAh rechargeable batteries, which are

commercially available.

· Be sure to read the instructions of the purchased rechargeable batteries before

use.

· When using on rechargeable batteries for the first time, charge them until the

battery indicator goes out.

· Before charging the batteries, close the disc compartment. You cannot charge

the batteries while it is opened.

1 Insert the rechargeable batteries with the

0 and 9 marks correctly

aligned.

2 Connect the AC adaptor.

Pull out the rubber cap before connecting the adaptor.

1 to DC 5 ~ 6 V jack

2 to a wall outlet

3 Keep

sSTOP/OFF/CHARGE pressed for about 1 second to start charging.

"C-On" appears, and the battery indicator blinks.

When charging is completed, "C-OFF" flashes a few times, and the battery

indicator goes out.

After charging, disconnect the AC adaptor.

Time to recharge the batteries

Recharge the batteries when

lights. If the unit remains in use after

lights, "Lo-bAtt" appears and the current operation stops.

To stop charging

Press

sSTOP/OFF/CHARGE during charging.

Force charging

When the recharging stops after only few minutes or the batteries cannot be fully

recharged, press

sSTOP/OFF/CHARGE while pressing PLAY MODE to start

force charging.

ATTENTION:

The product you have purchased can be powered by

nickel cadmium batteries which are recyclable. At the

end of their useful life, under various state and local

laws, it is illegal to dispose of these batteries into your

municipal waste stream.

Please call 1-800-289-2492 for information on how to

recycle these batteries.

USING ON AC HOUSE CURRENT

Connect the supplied AC adaptor in the same way as when recharging the

batteries.

During operation on AC house current, all of the battery indicator disappears.

BEFORE PLAYBACK

HOLD switch

Release the HOLD switch before playback.

When not using the unit, set the HOLD switch to the HOLD position.

Accidentally pressed button will not function.

If buttons are pressed when the HOLD switch is set to the HOLD position, "HOLd"

flashes in the display.

Turning on and off

Turning the power on

Press

ePLAY/PAUSE. Power is turned on and playback starts.

Note

"Err" appears on the display in the following cases:

When you try to play the unit without a disc in the disc compartment.

When you play a disc placed upside-down or a defective disc.

Turning the power off

If no new operations are done within 30 seconds from the end of last operation,

the power is turned off automatically. (Auto power off function)

· You can turn off the power by pressing

sSTOP/OFF/CHARGE before it is

automatically turned off.

Standby mode

When an operation finishes, the unit goes into standby mode until the auto power

off function automatically turns off the power.

To enter standby mode, press

ePLAY/PAUSE to start playback, then press

sSTOP/OFF/CHARGE.

Adjusting the sound

Volume

Press

+ to increase the volume.

Press

- to decrease the volume.

DSL

Press DSL repeatedly for more powerful sound and deeper bass.

: Deep bass is emphasized.

: Deep bass is strongly emphasized.

E 12

H 1

DC 5~6V

STOP/OFF

CHARGE

STOP/OFF

CHARGE

PLAY/PAUSE

PLAY MODE

DSL

VOLUME

XP-SR321/SR320(AU) E Page 1

Press

to decrease the volume.

DSL

Press DSL repeatedly for more powerful sound and deeper bass.

: Deep bass is emphasized.

: Deep bass is strongly emphasized.

: Normal sound

Signal sound function

You can check the operation by beep sound when you press an operation button.

The signal sound function is activated when you purchase this unit.

To cancel the signal sound function, press

ePLAY/PAUSE while pressing

PLAY MODE to display "

" while the power is off.

To resume the beep sound, repeat this procedure.

Inserting a disc

1 Set the dial to the OPEN position to open the disc compartment.

2 Place a disc in the center with the label side facing up.

3 Close the disc compartment tightly and set the dial to the LOCK position.

To remove the disc

Pick up the disc, holding its edge, while pressing the pivot gently.

Note

· The unit may not play a CD-R/RW disc that is recorded on personal computers

or some kinds of CD-R/RW recorders because of differences in recording

platforms.

· Do not attach any seal or label to either side (the recordable side or the labeled

side) of a CD-R/RW disc. It may cause malfunction.

01.3.29, 5:07 PM

PLAYBACK

Pull out the rubber cap and connect the supplied headphones to the PHONES/

LINE OUT jack.

The amplified speaker system can be connected instead to enjoy the CD sound.

1 Release HOLD.

2 Place a disc.

3 Press

ePLAY/PAUSE.

Playback starts from the first track.

a track number

b elapsed playing time

c volume indicator

Basic operation

Display during playback

Press ENTER/DISP during playback to change the display as follows.

1 Track display and elapsed playing time (normal display)

2 Track display and remaining playing time of the track in play

3 Remaining number of tracks and remaining playing time

The time is not displayed in following cases.

· When trying to program tracks beyond No.32.

· When the total remaining time of the programmed tracks is over 100 minutes.

E·A·S·S 3

× (Electronic Anti-Shock System) L

The E·A·S·S 3

× function reduces skipping or muting of the sound when the unit

is subjected to shocks.

The player keeps about 48 seconds or 12 seconds of playback sound in its

memory.

When you start playback, the unit keeps 48 seconds in memory.

To keep 12 seconds in the memory, press E·A·S·S repeatedly until

and

appear.

To cancel the E·A·S·S 3

× function, press E·A·S·S repeatedly until E·A·S·S

appears.

Note

· Before jogging with this unit, allow sufficient time for the memory buffer to fill up

completely (ideally about 20 seconds).

Continuous shock or vibration may cause the sound to be interrupted even if

the E·A·S·S 3

× function is activated. This is normal and not a malfunction.

Should you experience an interruption in sound, stabilize the unit for a few

seconds, then resume your activity.

· When the E·A·S·S 3

× function is activated, motor noise is heard as the motor

periodically rotates at high speed during playback. This is not a malfunction.

· When E·A·S·S is pressed, the unit will pause for about 2 seconds.

· When the unit is set to E·A·S·S-off or -12 second mode, the quality of the

sound will be better than E·A·S·S-48 second mode.

Resume function

Set the HOLD switch to RESUME.

appears, and you can start playback from the point where you stopped

playback by pressing

sSTOP/OFF/CHARGE.

When the resume function is on, all-track repeat is selected automatically.

To cancel resume play, set the HOLD switch to OFF.

Note

· Resume play may start at a point about 30 seconds behind or ahead the stopped

point. Resume play may not operate if you stopped at the last 30 seconds of

the final track.

· Resume play will be canceled if you open the disc compartment. If the unit is

turned off, resume play will not be canceled. In this case, be sure to set the

HOLD switch to OFF before changing discs.

Random play

Press PLAY MODE while in standby mode to display

Tracks on the disc are played in random order.

To cancel random play, press PLAY MODE while in standby mode.

display changes to

Note

· You cannot back to previous track by pressing

r during random play.

· You cannot select one-track repeat during random play.

Repeat play

Press PLAY MODE during playback to select repeat play as follows.

: one-track repeat

: all-track repeat

E.A.S.S

STOP/OFF

CHARGE

PHONES/

LINE OUT

PLAY MODE

PLAY/PAUSE

To stop

To pause

To search for the beginning of a track

To locate a desired passage

Press

sSTOP/OFF/CHARGE.

Press

ePLAY/PAUSE.

To resume, press it again.

Press

r or t.

Keep

r or t pressed.

Release the button at the start of desired

passage.

ENTER/DISP