AIWA CDC-Z127 - Owner's Manual Immediate Download

CDC-Z127 YU

STEREO CAR CD RECEIVER

RADIO-TOCADISCOS DE CD ESTEREOFONICO PARA

AUTOMOVIL

OWNER'S RECORD

For your convenience, record the model number and

serial number (you will find them on the bottom side of

your set) in the space provided below. Please refer to

them when you contact your AIWA dealer in case of

difficulty.

Model No. CDC-Z127

Serial No.

ENGLISH

ESPAÑOL

FRANÇAIS

OPERATING INSTRUCTIONS

MANUAL DE INSTRUCCIONES

MODE D'EMPLOI

8C-KCH-901-01

011120ATM-OX

1 ENGLISH

PRECAUTIONS

· Use only in a 12-volt DC negative-ground electrical

system.

· Disconnect the vehicle's negative battery terminal

while mounting and connecting the unit.

· When replacing the fuse, be sure to use one with an

identical amperage rating. Using a fuse with a higher

amperage rating may cause serious damage to the

unit.

· Do NOT attempt to disassemble the unit. Laser beams

from the optical pickup are dangerous to the eyes.

· Make sure that pins or other foreign objects do not get

inside the unit; they may cause malfunctions, or create

safety hazards such as electrical shock or laser beam

exposure.

· When your vehicle has been parked in direct sunlight

resulting in a considerable rise in the temperature

inside, allow the unit to cool off before operating it.

· Keep the volume at a level at which you can hear

outside warning sounds (horns, sirens, etc.).

NOTE

This equipment has been tested and found to comply

with the limits for a Class B digital device, pursuant to

Part 15 of the FCC Rules. These limits are designed to

provide reasonable protection against harmful

interference in a residential installation.

This equipment generates, uses, and can radiate radio

frequency energy and, if not installed and used in

accordance with the instructions, may cause harmful

interference to radio communications. However, there

is no guarantee that interference will not occur in a

particular installation. If this equipment does cause

harmful interference to radio or television reception,

which can be determined by turning the equipment off

and on, the user is encouraged to try to correct the

interference by one or more of the following measures:

-- Reorient or relocate the receiving antenna.

-- Increase the separation between the equipment

and receiver.

-- Connect the equipment into an outlet on circuit

different from that to which the receiver is connected.

-- Consult the dealer or an experienced radio/TV

technician for help.

CAUTION

Modifications or adjustments to this product, which are

not expressly approved by the manufacturer, may void

the user's right or authority to operate this product.

In addition to ordinary CDs, CD-Rs or CD-RWs can

be read by this unit. However, NEVER use a CD-R or

CD-RW that contains no data or data in the wrong

format, such as MP3 or other computer files.

1 ENGLISH

TABLE OF CONTENTS

BASIC OPERATION, AUDIO AND CLOCK

ADJUSTMENT ..................................................... 2

RADIO OPERATION ................................................. 3

CD PLAYER OPERATION ........................................ 4

AUXILIARY EQUIPMENT ......................................... 5

OTHER FUNCTION .................................................. 5

TROUBLESHOOTING .............................................. 5

MAINTENANCE ........................................................ 5

SPECIFICATIONS .................................................... 6

Note

Some buttons are assigned two or more functions.

For detailed descriptions, refer to the related pages.

CD Notes

· Playing a defective or dusty CD can

cause dropouts in sound.

· Hold CDs as illustrated.

· Do NOT touch the unlabeled side.

· Do NOT attach any seal, label or data protection sheet

to either side of CD.

· Do NOT expose a CD to direct sunlight or excessive

heat.

· Wipe a dirty CD from the center outward with a

cleaning cloth.

Never use solvents such as benzine or alcohol.

· This unit cannot play 3-inch (8 cm) CDs.

· NEVER insert a 3-inch CD contained in the adapter or

any irregularly shaped CD.

The unit may not be able to eject it, resulting in a

malfunction.

ENGLISH

BASIC OPERATION,

AUDIO AND CLOCK

ADJUSTMENT

PWR/MUTE

SEL

DISP

BAND

SRC

AUDIO CONTROL

i/k

Turning the unit on/off

· Press PWR/MUTE to turn on the unit. The unit also

turns on when you insert a CD.

· Press and hold PWR/MUTE until the unit turns off.

Note

Most operations described in this manual require the

unit to be turned on before starting the operation,

unless explicitly stated otherwise.

Changing the source mode

1 Press SRC.

Pressing SRC cycles through source modes in the

following order:

FM1 (FM2/FM3/AM1/AM2)

CD* AUX

* "CD" does not appear in the display when there is no

CD in the unit.

Adjusting the volume

1 Turn AUDIO CONTROL.

VOL (volume) indicator flashes.

Muting the sound

1 Press PWR/MUTE briefly.

MUTE indicator flashes.

To restore volume, briefly press PWR/MUTE again.

Adjusting sound

You can select the following modes for adjusting sound

depending on the music you listen to: BASS (low

frequencies), TRE (high frequencies), BAL (left/right),

FAD (front/ rear) and H-BASS (high bass).

ENGLISH

1 Press SEL repeatedly to select the mode to be

adjusted.

Pressing SEL cycles through the modes. The

selected mode's indicator flashes.

2 Turn AUDIO CONTROL to increase/decrease the

level or to select on/off for the selected mode.

Note

Adjust the level or select on/off within 5 seconds, or the

selected mode will return to previous state.

Aligning the source levels

(Source Level Adjuster)

Volume may vary each time you change the source

mode. In this case, you can align each source mode's

volume to almost the same level.

1 Press SRC or BAND repeatedly to select the desired

mode.

2 Press DISP while pressing SEL.

"LA 0" appears in the display.

3 Turn AUDIO CONTROL to adjust the level.

Note

Adjust the level within 5 seconds, or the selected mode

will be canceled.

Restoring the factory settings

1 Turn off the unit.

2 Press and hold DISP until "LA --" appears in the

display.

Note

You can restore the factory settings only for VOL,

BASS, TRE, BAL, FAD, and H-BASS, and aligned

source volume levels.

Muting button beep sounds

1 Turn off the unit.

2 Press and hold SEL until "bEEP" appears in the

display.

3 Turn AUDIO CONTROL to select on (level indicators

appear) or off (level indicators disappear).

4 Press SEL.

3 ENGLISH

Setting the clock

1 Press and hold DISP until the clock indicator

flashes in the display.

2 Press i (to set hour) or k (to set minute), and

then turn AUDIO CONTROL.

3 Press DISP.

Displaying the clock

1 Press DISP.

To return to the former display, press DISP again.

RADIO OPERATION

Tuning in to a station

(Seek/Manual Tuning)

i/k BAND

Stereo indicator

Local indicator

Band indicator

Frequency indication

1 Press BAND repeatedly to select the desired band

(FM1, FM2, FM3, AM1, or AM2).

2* Press i (to move to higher frequencies) or k (to

move to lower frequencies) to tune in to a station.

"ST" appears in the display when an FM station is

broadcasting in stereo, and receiving conditions are

good.

*Seek Tuning and Manual Tuning

· Press and hold

i or k until seek Tuning starts.

The unit locates a station automatically (Seek Tuning).

· Press

i or k repeatedly to search for a desired

station while increasing or decreasing the frequency

step by step (Manual Tuning).

To stop Seek Tuning, press

i or k again.

Preset station buttons 1 to 6

Monaural mode

When signals become weak, or reception becomes

poor, the unit automatically switches to Monaural mode

to reduce noise.

Local mode

Local mode allows you to tune in only to strong stations

during Seek Tuning.

1 Press LO before you start seek tuning.

"LO" appears in the display.

To return to Distant mode, press LO again.

"LO" disappears and the unit tunes in to all receivable

stations.

Using preset stations

You must preset stations before you can tune in a station

using preset station number buttons.

i/k

PS/A.ME

BAND

Preset station number

Presetting stations automatically

(Auto Memory)

1 Press BAND repeatedly to select the desired band

(FM1, FM2, FM3, AM1, or AM2).

2 Press and hold PS/A.ME until automatic presetting

starts.

The unit automatically stores up to 6 stations for

each band.

After completion of automatic presetting, the unit

tunes in to the station stored on preset station

button 1.

To cancel automatic presetting, press PS/A.ME again.

Checking the preset stations (Preset Scan)

1 Press PS/A.ME briefly.

Each preset station will be tuned in for 5 seconds in

order.

To cancel Preset Scan, press PS/A.ME again or any

preset station button.

ENGLISH

Presetting stations manually

(Manual Memory)

1 Press BAND repeatedly to select the desired band

(FM1, FM2, FM3, AM1, or AM2).

2 Press i or k to tune in to a desired station (see

"Tuning in to a station" as well for another tuning

method).

3 Press and hold the desired preset station button until

the unit beeps.

Note

A newly preset station replaces the station on the same

band that was previously stored on that preset station

button.

Tuning in to a preset station

1 Press BAND repeatedly to select the desired band

(FM1, FM2, FM3, AM1 or AM2).

2 Press the preset station button on which the desired

station is stored.

Active tuning reception control (ATRC)

The unit automatically suppresses FM noise caused by

vehicle movement, and maintains sound quality.

CD PLAYER OPERATION

Playing a CD

You can play CDs, CD-Rs and CD-RWs using the

procedure described below.

r/t

INT RNDM

REP 1

SRC

1 Insert a CD.

"CD" appears in the display.

CD play starts.

If a CD is already inserted, press SRC repeatedly to

select CD play mode.

In normal play, when the last track finishes, the unit

returns to the first track and continues to play.

Labeled-side up

Track number

CD indicator Elapsed playing time

Note

· When you play a CD that is already inserted, CD play

starts at the point where it stopped the previous time.

A newly inserted CD starts from the first track.

· A CD-R or CD-RW may take some time to start playing

back, but this is not a malfunction.

· If a CD-R or CD-RW with no data or incompatible data

is inserted, "E03" will appear in the display. The unit

cannot play such discs.

Intro Play

You can locate a desired track by monitoring the first 10

seconds of all the tracks on a CD.

1 Press INT during CD play.

"SCAN" appears in the display.

2 Press INT again when the desired track is played.

The unit returns to normal CD play.

One track Repeat Play

You can play a track repeatedly.

1 Press REP1 during CD play.

"REPEAT1" appears in the display.

To cancel One track Repeat Play, press REP1 again.

Eject a CD

Skip to the next track

Go back to the beginning

of the current track

Each extra press skips

backward one extra track

Locate a specific point in

a track

Press

Press and hold

r or

t until you find the

point.