AIWA CDCX417 - Owner's Manual Immediate Download

CDC-X517M YU

CDC-X417 YU

CDC-X317 YU

STEREO CAR CD RECEIVER

RADIO-TOCADISCOS DE CD ESTEREOFONICO PARA

AUTOMOVIL

OWNER'S RECORD

For your convenience, record the model number and

serial number (you will find them on the bottom side of

your set) in the space provided below. Please refer to

them when you contact your AIWA dealer in case of

difficulty.

Model No. CDC-X517M, CDC-X417, CDC-X317

Serial No.

ENGLISH

ESPAÑOL

FRANÇAIS

OPERATING INSTRUCTIONS

MANUAL DE INSTRUCCIONES

MODE D'EMPLOI

000/CDC-X517M/X417/X317(YU)Cov.

00.12.25, 2:43 PM

CDCX517MX417/X317(YU)-total-En-2

1 ENGLISH

PRECAUTIONS

· Use only in a 12-volt DC negative-ground electrical

system.

· Disconnect the vehicle's negative battery terminal

while mounting and connecting the unit.

· When replacing the fuse, be sure to use one with an

identical amperage rating. Using a fuse with a higher

amperage rating may cause serious damage to the

unit.

· Do NOT attempt to disassemble the unit. Laser beams

from the optical pickup are dangerous to the eyes.

· Make sure that pins or other foreign objects do not get

inside the unit; they may cause malfunctions, or create

safety hazards such as electrical shock or laser beam

exposure.

· When your vehicle has been parked in direct sunlight

resulting in a considerable rise in the temperature

inside, allow the unit to cool off before operating it.

· Keep the volume at a level at which you can hear

outside warning sounds (horns, sirens, etc.).

NOTE

This equipment has been tested and found to comply

with the limits for a Class B digital device, pursuant to

Part 15 of the FCC Rules. These limits are designed to

provide reasonable protection against harmful

interference in a residential installation.

This equipment generates, uses, and can radiate radio

frequency energy and, if not installed and used in

accordance with the instructions, may cause harmful

interference to radio communications. However, there

is no guarantee that interference will not occur in a

particular installation. If this equipment does cause

harmful interference to radio or television reception,

which can be determined by turning the equipment off

and on, the user is encouraged to try to correct the

interference by one or more of the following measures:

-- Reorient or relocate the receiving antenna.

-- Increase the separation between the equipment

and receiver.

-- Connect the equipment into an outlet on circuit

different from that to which the receiver is connected.

-- Consult the dealer or an experienced radio/TV

technician for help.

CAUTION

Modifications or adjustments to this product, which are

not expressly approved by the manufacturer, may void

the user's right or authority to operate this product.

In addition to ordinary CDs, CD-Rs or CD-RWs can

be read by this unit. However, NEVER use a CD-R or

CD-RW that contains no data or data in the wrong

format, such as MP3 or other computer files.

1 ENGLISH

TABLE OF CONTENTS

THEFT PROTECTION .............................................. 2

BASIC OPERATION, AUDIO AND CLOCK

ADJUSTMENT ..................................................... 2

RADIO OPERATION ................................................ 3

CD PLAYER OPERATION ....................................... 5

AUXILIARY EQUIPMENT ......................................... 6

OTHER FUNCTIONS ............................................... 6

STEERING WHEEL REMOTE CONTROL

(CDC-X517M and CDC-X417) ............................. 6

CD CHANGER OPERATION (CDC-X517M only) .... 6

TROUBLESHOOTING .............................................. 7

MAINTENANCE ........................................................ 7

SPECIFICATIONS .................................................... 8

Notes

· These operating instructions cover the CDC-X517M,

CDC-X417, and CDC-X317.

· The figures in these operating instructions show the

CDC-X517M.

· Some buttons are assigned two or more functions.

For detailed descriptions, refer to the related pages.

CD changer

(optional) control

function

CDC-X517M

yes

CDC-X417,

CDC-X317

CD Notes

· Playing a defective or dusty CD can

cause dropouts in sound.

· Hold CDs as illustrated.

· Do NOT touch the unlabeled side.

· Do NOT attach any seal, label or data protection sheet

to either side of a disc.

· Do NOT expose a CD to direct sunlight or excessive

heat.

· Wipe a dirty CD from the center outward with a cleaning

cloth.

Never use solvents such as benzine or alcohol.

· This unit cannot play 3-inch (8 cm) CDs.

· NEVER insert a 3-inch CD contained in the adapter or

any irregularly shaped CD.

The unit may not be able to eject it, resulting in a

malfunction.

001/CDC-X517M/X417/X317(YU)E

00.12.25, 2:45 PM

CDCX517MX417/X317(YU)-total-En-3

ENGLISH

THEFT PROTECTION

Take the front panel with you when leaving the car, and

keep it in the supplied carrying case.

Detaching the front panel

Before detaching the front panel, remove the CD to

prevent possible damage to the unit.

1 Press z to remove the CD.

2 Press and hold PWR/MUTE until the unit turns off.

3 Press %. (Hold the panel with one hand to prevent

accidentally dropping it.)

4 Remove the panel.

Attaching the front panel

1 Engage the left side of the front panel to the left catch

on the unit.

2 Push the panel forward until it locks. Be sure not to

press any buttons while you are attaching the panel.

Note

Do not touch the front panel connector. This could cause

a poor or faulty connection.

Security lamp

The security lamp will continue to flash while the front

panel is detached from the unit.

BASIC OPERATION,

AUDIO AND CLOCK

ADJUSTMENT

Turning the unit on/off

· Press PWR/MUTE to turn on the unit. The unit also

turns on when you insert a CD.

· Press and hold PWR/MUTE until the unit turns off.

Note

Most operations described in this manual require the

unit to be turned on before starting the operation, unless

explicitly stated otherwise.

Changing the source mode

1 Press FNC.

Pressing FNC cycles through source modes in the

following order:

* "CD" does not appear in the display when there is no

CD in the unit.

**CD Changer Play mode (CDC-X517M only, available

when an optional CD Changer is connected)

Adjusting the volume

1 Turn the Smart Jog.

VOL (volume) indicator flashes.

Muting the sound

1 Press PWR/MUTE briefly.

To restore volume, briefly press PWR/MUTE again.

Smart Jog

001/CDC-X517M/X417/X317(YU)E

00.12.25, 2:45 PM

CDCX517MX417/X317(YU)-total-En-4

3 ENGLISH

Adjusting sound

You can select the following modes for adjusting sound

depending on the music you listen to: BASS (low

frequencies), TRE (high frequencies), BAL (left/right),

FAD (front/ rear) and H-BASS (high bass)

1 Press SEL repeatedly to select the mode to be

adjusted.

Pressing SEL cycles through the modes. The

selected mode's indicator flashes.

2 Turn the Smart Jog to increase or decrease the level

for the selected mode (except for H-BASS).

In H-BASS mode, turn the Smart Jog to select on or

off.

Note

Adjust the level or select on/off within 5 seconds, or the

selected mode will return to previous state.

Aligning the source levels

(Source Level Adjuster)

Volume may vary each time you change the source

mode. In this case, you can align each source mode's

volume to almost the same level.

1 Press FNC repeatedly to select the desired mode.

2 Press DISP while pressing SEL.

"LA 0" appears in the display.

3 Turn the Smart Jog to adjust the level.

Note

Adjust the level within 5 seconds, or the selected mode

will be canceled.

Restoring the factory settings

1 Turn off the unit.

2 Press and hold DISP until "LA --" appears in the

display.

Note

You can restore the factory settings only for VOL, BASS,

TRE, BAL, FAD, and H-BASS, and aligned source

volume levels.

Muting button beep sounds

1 Turn off the unit.

2 Press and hold SEL until "bEEP" appears in the

display.

3 Turn the Smart Jog to select on (level indicators

appear) or off (level indicators disappear).

4 Press and hold SEL until the unit turns off.

Stereo indicator Local indicator

Setting the clock

1 Press and hold DISP until the clock indicator flashes

in the display.

2 Press TUNEi (to set hour) or TUNEk (to set

minute) and turn the Smart Jog.

3 Press DISP.

Displaying the clock

1 Press DISP.

To return to the former display, press DISP again.

RADIO OPERATION

Tuning in to a station

(Seek/Manual Tuning)

Band indicator

Frequency indication

1 Press FNC repeatedly to select the desired band

(FM1, FM2, FM3, AM1 or AM2).

2* Press TUNEi (to move to higher frequencies) or

TUNE

k (to move to lower frequencies) to tune in to

a station.

"ST" appears in the display when a station is

broadcasting in stereo, and receiving conditions are

good.

*Seek Tuning and Manual Tuning

· Press and hold TUNE

i or TUNEk until seek Tuning

starts.

The unit locates a station automatically (Seek Tuning).

· Press TUNE

i or TUNEk repeatedly to search for a

desired station while increasing or decreasing the

frequency step by step (Manual Tuning).

To stop Seek Tuning, press TUNE

i or TUNEk

again.

Monaural mode

When signals become weak, or reception becomes

poor, the unit automatically switches to Monaural mode

to reduce noise.

001/CDC-X517M/X417/X317(YU)E

00.12.25, 2:45 PM

CDCX517MX417/X317(YU)-total-En-5

ENGLISH

Local mode

Local mode allows you to tune in only to strong stations

during Seek Tuning.

1 Press LO before you start seek tuning.

"LO" appears in the display.

To return to Distant mode, press LO again.

"LO" disappears and the unit tunes in to all receivable

stations.

Using preset stations

You must preset stations before you can tune in a station

using preset station number buttons.

Preset station

number

Presetting stations automatically

(Auto Memory)

1 Press FNC repeatedly to select the desired band

(FM1, FM2, FM3, AM1 or AM2).

2 Press and hold PS/A.ME until automatic presetting

starts.

The unit automatically stores up to 6 stations for

each band.

After completion of automatic presetting, the unit

tunes in to the station stored on preset station

button 1.

To cancel automatic presetting, press PS/A.ME again.

Checking the preset stations (Preset Scan)

1 Press PS/A.ME briefly.

Each preset station will be tuned in for 5 seconds in

order.

To cancel Preset Scan, press PS/A.ME again or any

preset station button.

Presetting stations manually

(Manual Memory)

1 Press FNC repeatedly to select the desired band

(FM1, FM2, FM3, AM1 or AM2).

2 Press TUNEi or TUNEk to tune in to a desired

station (see "Tuning in to a station," page 3).

3 Press the desired preset station button until the unit

beeps.

Note

A newly preset station replaces the station on the same

band that was previously stored on that preset station

button.

Tuning in to a preset station

1 Press FNC repeatedly to select the desired band

(FM1, FM2, FM3, AM1 or AM2).

2 Press the preset station button on which the desired

station is stored.

Active tuning reception control (ATRC)

The unit automatically suppresses FM noise caused by

vehicle movement, and maintains sound quality.

Using the timer

(My Information)

You can schedule the radio to activate for daily radio

programs. The unit automatically turns on and off in

Radio mode at the scheduled times.

Setting the timer

1 Turn off the unit.

2 Press and hold INFO until "PO" flashes in the

display.

3 Press SEL.

4 Set the time you wish the unit to turn on.

· Press TUNE

i and turn the Smart Jog to set the hour.

· Press TUNE

k and turn the Smart Jog to set the

minute.

5 Press SEL.

6 Press FNC to select the band.

7 Press TUNEi,TUNEkor the desired preset station

button to select the station.

8 Press SEL.

9 Set the time you wish the unit to turn off following the

same procedure used in step 4.

Preset station buttons 1 ~ 6

MY INFO indicator

Smart Jog

001/CDC-X517M/X417/X317(YU)E

00.12.25, 2:45 PM