AIWA ADCM105 - Owner's Manual Immediate Download

OPERATING INSTRUCTIONS

MANUAL DE INSTRUCCIONES

MODE D'EMPLOI

ADC-M105YU

COMPACT DISC CHANGER

CAMBIADOR DE DISCOS COMPACTOS

ENGLISH

FRANÇAIS

ESPAÑOL

OWNER'S RECORD

For your convenience, record the model number

and serial number (you will find them on the rear of

your set) in the space provided below. Please refer

to them when you contact your AIWA dealer in

case of difficulty.

Model No. ADC-M105

Serial No.

8Z-KM3-922-01

001110ATM-OX

00ADCM105.YU.Cov

01.1.31, 3:52 PM

Welcome

Thank you for your purchasing this AIWA product. To optimize the performance of this unit, please read

through this manual carefully.

TABLE OF CONTENTS

FEATURES .......................................................................................................................................... 1

PRECAUTIONS ................................................................................................................................... 2

UNPACKING ........................................................................................................................................ 3

INSTALLATIONS ................................................................................................................................. 4

CONNECTIONS .................................................................................................................................. 8

HOW TO USE ...................................................................................................................................... 9

SPECIFICATIONS ............................................................................................................................. 10

FEATURES

1 ENGLISH

· Tracks from 10 CDs stored in the disc magazine

can be selected and played.

· Horizontal, vertical, slanted or suspended

installation can be made.

· Through the window at the top of the unit, you

can see a disc spinning as it plays.

· Since it is smaller in size, you will find it easier

to install the unit.

NOTE

This equipment has been tested and found to

comply with the limits for a Class B digital device,

pursuant to Part 15 of the FCC Rules. These

limits are designed to provide reasonable

protection against harmful interference in a

residential installation.

This equipment generates, uses, and can radiate

radio frequency energy and, if not installed and

used in accordance with the instructions, may

cause

harmful

interference

radio

communications. However, there is no guarantee

that interference will not occur in a particular

installation. If this equipment does cause harmful

interference to radio or television reception, which

can be determined by turning the equipment off

and on, the user is encouraged to try to correct

the interference by one or more of the following

measures:

-- Reorient or relocate the receiving antenna.

-- Increase the separation between the

equipment and receiver.

-- Connect the equipment into an outlet on

circuit different from that to which the receiver

is connected.

-- Consult the dealer or an experienced radio/

TV technician for help.

CAUTION

Modifications or adjustments to this product, which

are not expressly approved by the manufacturer,

may void the user's right or authority to operate

this product.

In addition to ordinary CDs, CD-Rs or CD-RWs

can be read by this unit. However, NEVER use

a CD-R or CD-RW that contains no data or data

in the wrong format, such as MP3 or other

computer files.

When you insert a CD-R/CD-RW, it may take

longer to start playing.

01ADCM105.YU.E

01.1.31, 3:53 PM

PRECAUTIONS

· Do NOT install the unit in a location where it

may be subjected to:

-- Direct sunlight or other sources of excessive

heat

-- Fluid, rain or moisture

-- Excessive dirt or dust

-- Excessive vibration

· This unit is designed to be operated on a 12-volt

DC negative-ground electrical system only.

· Choose the mounting location carefully so that

the unit will not interfere with normal driving

functions.

· Before making connections, disconnect the

(

terminal of the car battery to avoid short

circuiting.

Notes on CDs

· A defective or soiled disc stored in the disc

magazine can cause the sound to drop out

during play.

· Always handle a disc by holding its inner and

outer edges.

· Do NOT touch the surface of the unlabeled side

of the disc.

· Do NOT attach paper or tape etc. to a disc.

· Do NOT expose the discs to direct sunlight or

excessive heat.

· Clean the discs before inserting them into the

disc magazine. Always clean a disc from the

center outward with a cleaning cloth.

· There may be burrs left on the inner and outer

edges of a brand-new disc.

The burr may

cause the malfunction of the unit or sound drop-

out. To prevent these problems, if the burr is

left on the disc, be sure to remove them with a

ball-point pen, etc. as illustrated.

· NEVER use solvents such as benzine or alcohol

to clean a disc.

· You cannot play an 8-cm (3-inch) CD -- even

with the specially designed adaptor.

· Do NOT use irregular shape CDs (example:

heart-shaped, octagonal ones).

It may result in malfunction.

Notes on the disc magazine

· Do NOT leave the disc magazine in a place

subject to excessive temperature or humidity.

· Do NOT insert more than one disc per slot.

· Do NOT drop the disc magazine.

ENGLISH

Ball-point pen

Burr

Ball-point pen

Burr

01ADCM105.YU.E

01.1.31, 3:53 PM

UNPACKING

a Brackets (1 pair)

Supplied mounting kit

for the compact disc changer

The letters are keyed to those in the instructions.

Use only the supplied mounting hardware for safe and secure installation.

Compact disc changer

e Adhesive label

(1 sheet)

d Nuts (4 ea.)

c Plate brackets

(2 ea.)

b Washer screws

(4 ea.)

Compact disc magazine

Connecting cable

3 ENGLISH

01ADCM105.YU.E

01.1.31, 3:53 PM

INSTALLATIONS

Precautions

Select the mounting location very carefully,

referring to the following points.

· Make sure that there is no fuel tank, wiring or

piping on the other side of the mounting surface.

· Make sure that the installation of the unit will not

hinder the movement of the deck lid or interfere

with the spare tire, etc.

· Use only the supplied mounting kit for safe and

proper installation.

Removing the transport screws

Find the three transport screws at the bottom of

the unit, which lock the unit's mechanism during

transport. Remove these screws before

installation.

Retain these screws and replace them in the

original positions if the unit is transported for

service or maintenance.

Mounting angle setting levers

Be sure to change the position of both mounting

angle setting levers according to the angle at

which the unit is to be installed.

Notes

· Be sure to eject the disc magazine when you set the

levers.

· Be sure to set both levers to the same position.

· Be sure to set the levers exactly at the position (notch).

If the lever is deviate from the position, the sound may

drop out.

· Care must be taken when you mount the unit at the

angle of lower than level. The disc magazine may drop

if you eject the magazine.

· Do NOT turn over the unit or slide the lever when the

unit is activated. Doing so may damage the mechanism

or the discs in the unit.

· The mounting angle setting levers on each side of the

unit are factory-set to the HORIZONTAL position.

· When you complete the setting, attach the supplied

adhesive labels e over the slots.

ENGLISH

Insert a pointed object such as a screw driver or

ball-point pen, etc. into the low spot of the lever

and slide the lever to the position from among

HORIZONTAL, 45°, and VERTICAL positions.

Mounting angle setting levers

01ADCM105.YU.E

01.1.31, 3:53 PM